Hi Rich and the group,
Doug Smith
Sent from my iPhone
IPhone: 408-858-4528
Office: 702-570-6108
Email: [email protected]
Website: http://dsmith.org
________________________________
From: Richard Nute <[email protected]>
Sent: Wednesday, February 26, 2025 16:16
To: doug emcesd.com <[email protected]>
Cc: 'Pete Perkins' <[email protected]>; [email protected]
<[email protected]>
Subject: re: major safety issue possibly affecting 20% of the electronic
devices in use
Be Careful With This Message
>From ("Richard Nute"
><[email protected]>)<https://godaddy.cloud-protect.net/email-details/?k=k1&payload=53616c7465645f5f33a5694d055ba3fcb7596fc748826b6878a4e38d65b07fb9bd4fe739748329fd7d69c215acb140f0d93f3a70827b9a7374498277c640ae6219d5d2eeb52373f59f140fc21f6f5372fa75398558b61982aaa804e860f3de3d4a8844418a31aa5051d91ea108013a84c6758820a2550e9bbe743c4769318eb8fb15692d2a0d6f40905c6b52e4f6948a78b236a8bb8e5db3c66eff3710bdcda9d98a776bfd1078afcc7971d38bf81d91fb3adb6320d038e4e4f4a34c8505c1daed62506ce876ed91afd3de0fed20d8ce1ab0dd0d304abfa0c7126bbb412f8155>
Learn
More<https://godaddy.cloud-protect.net/email-details/?k=k1&payload=53616c7465645f5f33a5694d055ba3fcb7596fc748826b6878a4e38d65b07fb9bd4fe739748329fd7d69c215acb140f0d93f3a70827b9a7374498277c640ae6219d5d2eeb52373f59f140fc21f6f5372fa75398558b61982aaa804e860f3de3d4a8844418a31aa5051d91ea108013a84c6758820a2550e9bbe743c4769318eb8fb15692d2a0d6f40905c6b52e4f6948a78b236a8bb8e5db3c66eff3710bdcda9d98a776bfd1078afcc7971d38bf81d91fb3adb6320d038e4e4f4a34c8505c1daed62506ce876ed91afd3de0fed20d8ce1ab0dd0d304abfa0c7126bbb412f8155>
Potential Impersonation
The sender's identity could not be verified and someone may be impersonating
the sender. Take caution when interacting with this message.
Hi Doug:
I am alarmed that you experienced breakdowns by an 800-volt pulse when the
dielectric strength of the primary circuits is at least 1500 volts rms. I have
a few questions:
1. What was the 800-volt waveform? You applied the pulse common mode, which
I assume is to both line and neutral conductors connected together and to the
ground wire. (This is the hi-pot test configuration.) Please confirm.
2. How did you detect breakdowns, especially in the next microseconds after
applying the pulse?
3. Small wall-warts are typically two-wire with no ground. (The hi-pot test
is to foil wrapped around the enclosure and to the secondary.) What was your
test configuration?
4. Primary-to-ground and primary-to-secondary in a typical product consists
of Y capacitors, solid insulation, and air insulation. Since the air insulation
is 2 mm or more, this is unlikely the site of the breakdown. Solid insulation
should easily withstand 800 volts (more likely 8,000 volts). So, this leaves
the Y capacitors as likely suspects. What is your guess as to the EUT
component that exhibits this phenomenon?
5. Were any of the units you tested malfunctional or permanently damaged
due to your tests?
6. How can we get a copy of your paper?
Thanks,
Rich
-
----------------------------------------------------------------
This message is from the IEEE Product Safety Engineering Society emc-pstc
discussion list. To post a message to the list, send your e-mail to
[email protected]
All emc-pstc postings are archived and searchable on the web at:
https://www.mail-archive.com/[email protected]/
Website: https://ewh.ieee.org/soc/pses/
Instructions: https://ewh.ieee.org/soc/pses/list.html (including how to
unsubscribe)
List rules:
https://pses.ieee.org/wp-content/uploads/2024/12/EM-PSTC-List-Rules.pdf
For help, send mail to the list administrators:
Mike Sherman at: [email protected]
Rick Linford at: [email protected]
For policy questions, send mail to:
Jim Bacher: <[email protected]>
_________________________________________________
To unsubscribe from the EMC-PSTC list, click the following link:
https://listserv.ieee.org/cgi-bin/wa?SUBED1=EMC-PSTC&A=1
