On Tuesday, May 29, 2012 03:10:01 PM John Thornton did opine: > Where should the 208v be? The mains are 244vac. > That means your wall socket voltage is about 122. Using the same math in kcalc, I get 211.310198523, but the meter will be great if it actually displays the .3. :)
The math is simple enough, sin(120)*voltage, where the 120 is the phase angle under ideal conditions. FWIW sin(120) and sin(60) return exactly the same value because the sin is mirrored around modulo 90 degrees where it is 1.00000, and is zero at 0 and 180 degrees. That is just about 1 step on the taps of your service pole can. The substation regulators can usually do finer work. That pole can, from the looks of this, should be able to feed your place with at least 25kw in order to be adequately 'stiff' enough for this level of load variations. I was bumping the 4 or 5 houses on my can just enough that my eyes could see it, so both the bigger bandsaw, and my 6" delta jointer (the one I trimmed my fingernails with) are now reconfigured for a 250 volt single phase feed. I don't even see the lights in the shop dim now. Its 6 gage buried range-like cable back to the 200 amp house service, nice and stiff. :) My AC has a 2.5 horse 127v motor on it and I need to do it the same way. Got a summer thunderboomer moving thru, noisy outside, but I am tempted to go setup the mill and see if I can make another encoder disk for the lathe. I have some thinner material now, salvaged from the color panel in the front door of a dishwasher that failed, black but I'll have to magnet test it to see if its ferrous, that if plastic I maybe can carve with a pcb drill for a mill. And I need to modify that code a bit so there is no width discontinuity for the long slot that is the index pulse. I may have to hit up Andy up for some math help because I don't think that code compensates for the mill radius when it tapers smaller at the inside radii of the slots. I get the impression that the taper it uses needs a /2 in order to aim the side of the carved slot directly at the center of the circle. > John > > On 5/29/2012 12:11 PM, Jon Elson wrote: > > gene heskett wrote: > >> I have another wild idea, your Vab, Vac, Vbc voltages would appear to > >> be moderately well balanced, as they should be. The generated C, > >> measured to ground, is quite hot as is also expected. > > > > Perfect should be 208 V, so 212 is quite close. > > > > Jon > > > > ---------------------------------------------------------------------- > > -------- Live Security Virtual Conference > > Exclusive live event will cover all the ways today's security and > > threat landscape has changed and how IT managers can respond. > > Discussions will include endpoint security, mobile security and the > > latest in malware threats. > > http://www.accelacomm.com/jaw/sfrnl04242012/114/50122263/ > > _______________________________________________ > > Emc-users mailing list > > [email protected] > > https://lists.sourceforge.net/lists/listinfo/emc-users > > ------------------------------------------------------------------------ > ------ Live Security Virtual Conference > Exclusive live event will cover all the ways today's security and > threat landscape has changed and how IT managers can respond. > Discussions will include endpoint security, mobile security and the > latest in malware threats. > http://www.accelacomm.com/jaw/sfrnl04242012/114/50122263/ > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users Cheers, Gene -- "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order." -Ed Howdershelt (Author) My web page: <http://coyoteden.dyndns-free.com:85/gene> It's as BAD as you think, and they ARE out to get you. ------------------------------------------------------------------------------ Live Security Virtual Conference Exclusive live event will cover all the ways today's security and threat landscape has changed and how IT managers can respond. Discussions will include endpoint security, mobile security and the latest in malware threats. http://www.accelacomm.com/jaw/sfrnl04242012/114/50122263/ _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
