Oki, i can admit im stupid.. I can reprogram prob. most of this software as needed. But when it comes to wiring i don't understand jack shit. Im the guy that would blank out the powergrid for my whole neighbourhood switching a light bulb.. Can you dumb it down for me??
Sure its quite common and input must be programmed.. Where.. where does it needs to be programmed? And the use of limit switches is .. circumvented with this input enable thingymajig? Or are the connected in series with the mesa card? Its not clear for someone that has installed a stepper motor at most before. // A Peter C. Wallace skrev den 2015-02-11 20:14: > On Wed, 11 Feb 2015, Andreas Pettersson wrote: > >> Date: Wed, 11 Feb 2015 19:57:39 +0100 >> From: Andreas Pettersson <andr...@roughedge.se> >> Reply-To: "Enhanced Machine Controller (EMC)" >> <emc-users@lists.sourceforge.net> >> To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.net> >> Subject: Re: [Emc-users] Need wiring advice, Argon + 7i48 >> >> Well if you look at this page, and you tell me.. is there a Enable drive >> pin?? >> http://granitedevices.com/wiki/Argon_user_guide/J5_connector_electrical_interfacing >> >> If there its called something else. :/ >> >> // Andreas > This is quite common, the general purpose input must be programmed > to determine their function > >> >> Peter C. Wallace skrev den 2015-02-11 18:28: >>> On Wed, 11 Feb 2015, Andreas Pettersson wrote: >>> >>>> Date: Wed, 11 Feb 2015 17:40:33 +0100 >>>> From: Andreas Pettersson <andr...@roughedge.se> >>>> Reply-To: "Enhanced Machine Controller (EMC)" >>>> <emc-users@lists.sourceforge.net> >>>> To: emc-users@lists.sourceforge.net >>>> Subject: Re: [Emc-users] Need wiring advice, Argon + 7i48 >>>> >>>> Can't actually find an enable input port on the Argon either. >>>> Guessing i either need to configure the device in the Granite software for >>>> what input signal it should expect and wire the anain- to ground and the >>>> anain+ to the AOUT0 for channel zero from the 7i48 then. >>> The 7I48 AOUTN connects to AIN+ and the adjacent AGND on the 7I48 >>> connnects to the drives AIO-. This connection should be done with a twsited >>> pair. >>> >>> There must be a separate drive enable. >>> >>> For active low enable you wire the drive enable pin to the 7I48 ENAN+ and >>> ground (or tie to drives input common) ENAN- >>> >>> For active high enables you connect the 7I48 ENAN+ to the input control >>> voltage and ENAN- to the drive enable input. >>>> I need to get hold of a wiring software im figuring excel is fine and >>>> dandy but not that really easy for everyone to understand. >>>> >>>> eusurplus dont have them in stock, he is backordered 6-8 weeks as well. >>>> >>>> // A >>>> >>>> On 2015-02-11 15:31, Ralph Stirling wrote: >>>>> Andreas, >>>>> >>>>> I believe (without looking at the Argon specs), that the >>>>> ANAIN+ signal on the Argon is the Analog Input (-10 to +10v >>>>> probably), which would connect to the AOUT0 on the 7I48. >>>>> ENA0+ on the 7I48 is an Enable Output. There should be an >>>>> enable input on the Argon, but I don't seen anything labeled >>>>> that way on your spreadsheet, so you need to examine the >>>>> manual more closely. >>>>> >>>>> -- Ralph >>>>> ________________________________________ >>>>> From: Andreas Pettersson [andr...@roughedge.se] >>>>> Sent: Tuesday, February 10, 2015 11:03 PM >>>>> To: emc-users@lists.sourceforge.net >>>>> Subject: [Emc-users] Need wiring advice, Argon + 7i48 >>>>> >>>>> So i got this Mesa 7i48 analog servo card, a 15pin differential encoder, >>>>> and the argon driver. >>>>> >>>>> Make notice i have no clue what im doing, so i made this chart and just >>>>> connect the pins together basicly >>>>> with a color chart. >>>>> >>>>> The Argon uses a 24V@0.4A DC input, and the mesa card uses 5V - but i >>>>> need to split the encoder cables from the Driver and connect em to the >>>>> mesa card as well.. Not sure if this is the right way of doing it. >>>>> >>>>> https://docs.google.com/spreadsheets/d/1u0vVnGZnDBdwTkmWv6m_r7q4JR2niON6E5N9PaSPE_4/edit#gid=0 >>>>> >>>>> Some advice on this subject would be appreciated. >>>>> >>>>> Regards, >>>>> Andreas >>>>> >>>>> ------------------------------------------------------------------------------ >>>>> Dive into the World of Parallel Programming. The Go Parallel Website, >>>>> sponsored by Intel and developed in partnership with Slashdot Media, is >>>>> your >>>>> hub for all things parallel software development, from weekly thought >>>>> leadership blogs to news, videos, case studies, tutorials and more. Take a >>>>> look and join the conversation now. http://goparallel.sourceforge.net/ >>>>> _______________________________________________ >>>>> Emc-users mailing list >>>>> Emc-users@lists.sourceforge.net >>>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>>>> >>>>> ------------------------------------------------------------------------------ >>>>> Dive into the World of Parallel Programming. The Go Parallel Website, >>>>> sponsored by Intel and developed in partnership with Slashdot Media, is >>>>> your >>>>> hub for all things parallel software development, from weekly thought >>>>> leadership blogs to news, videos, case studies, tutorials and more. Take a >>>>> look and join the conversation now. http://goparallel.sourceforge.net/ >>>>> _______________________________________________ >>>>> Emc-users mailing list >>>>> Emc-users@lists.sourceforge.net >>>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>>> ------------------------------------------------------------------------------ >>>> Dive into the World of Parallel Programming. The Go Parallel Website, >>>> sponsored by Intel and developed in partnership with Slashdot Media, is >>>> your >>>> hub for all things parallel software development, from weekly thought >>>> leadership blogs to news, videos, case studies, tutorials and more. Take a >>>> look and join the conversation now. http://goparallel.sourceforge.net/ >>>> _______________________________________________ >>>> Emc-users mailing list >>>> Emc-users@lists.sourceforge.net >>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>>> >>> Peter Wallace >>> Mesa Electronics >>> >>> (\__/) >>> (='.'=) This is Bunny. Copy and paste bunny into your >>> (")_(") signature to help him gain world domination. >>> >>> >>> ------------------------------------------------------------------------------ >>> Dive into the World of Parallel Programming. The Go Parallel Website, >>> sponsored by Intel and developed in partnership with Slashdot Media, is your >>> hub for all things parallel software development, from weekly thought >>> leadership blogs to news, videos, case studies, tutorials and more. Take a >>> look and join the conversation now. http://goparallel.sourceforge.net/ >>> _______________________________________________ >>> Emc-users mailing list >>> Emc-users@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/emc-users >> >> ------------------------------------------------------------------------------ >> Dive into the World of Parallel Programming. The Go Parallel Website, >> sponsored by Intel and developed in partnership with Slashdot Media, is your >> hub for all things parallel software development, from weekly thought >> leadership blogs to news, videos, case studies, tutorials and more. Take a >> look and join the conversation now. http://goparallel.sourceforge.net/ >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users >> > Peter Wallace > Mesa Electronics > > (\__/) > (='.'=) This is Bunny. Copy and paste bunny into your > (")_(") signature to help him gain world domination. > > > ------------------------------------------------------------------------------ > Dive into the World of Parallel Programming. The Go Parallel Website, > sponsored by Intel and developed in partnership with Slashdot Media, is your > hub for all things parallel software development, from weekly thought > leadership blogs to news, videos, case studies, tutorials and more. Take a > look and join the conversation now. http://goparallel.sourceforge.net/ > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users ------------------------------------------------------------------------------ Dive into the World of Parallel Programming. The Go Parallel Website, sponsored by Intel and developed in partnership with Slashdot Media, is your hub for all things parallel software development, from weekly thought leadership blogs to news, videos, case studies, tutorials and more. Take a look and join the conversation now. http://goparallel.sourceforge.net/ _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
