Good day Gene, Our best wishes to you both.
john ________________________________ From: Gene Heskett <[email protected]> Sent: Tuesday, 7 February 2017 2:19 PM To: [email protected] Subject: Re: [Emc-users] Raspberry Pi & 7i90HD again On Monday 06 February 2017 21:22:26 Gene Heskett wrote: > On Monday 06 February 2017 14:47:04 Andrew wrote: > > Hello, > > > > I want to try 7i90HD on my Raspberry Pi 2. I think Gene did that > > recently with Pi 3, so I digged through the list... but the > > information is a bit sparse. Also a lot of outdated info on the net. > > Please help me figure it out. > > > > First, I need to get LinuxCNC running: > > > > 1. Install a raspbian image. One of these? > > https://www.raspberrypi.org/downloads/raspbian/ Download Raspbian for Raspberry Pi<https://www.raspberrypi.org/downloads/raspbian/> www.raspberrypi.org Raspbian is the Foundation’s official supported operating system. You can install it with NOOBS or download the image below and follow our installation guide. > > Or this? > > https://sourceforge.net/projects/minibian/ MINIBIAN image for Raspberry Pi download | SourceForge.net<https://sourceforge.net/projects/minibian/> sourceforge.net MINIBIAN image for Raspberry Pi download. MINIBIAN image for Raspberry Pi 2016-10-30 19:55:06.129000 free download. MINIBIAN image for Raspberry Pi ... > > > > 2. Install preempt-rt kernel and headers > > http://deb.machinekit.io/debian/pool/main/l/linux-rt/linux-image-rpi > >2- rt_4.4.4-rt9-v7+-7_armhf.deb > > http://deb.machinekit.io/debian/pool/main/l/linux-rt/linux-headers-r > >pi 2-rt_4.4.4-rt9-v7+-7_armhf.deb > > > > 3. Install jessie master-sim from the buildbot. > > > > Anything else? > > Ask Matsche if his rpspi.so driver will run on a pi 2. Differences in > the gpio architecture may preclude that as the data rate on that bus > when its working is at 32 megabites a second while its flowing in 4, 8 > byte packets. per transaction. > This is not quite right, that should have been 4, 8 bit packets or bytes. I am somewhat distracted, and may not be as active here for a bit as my bride of 27+ years fell and broke a hip in a friends kitchen earlier this afternoon. A clean break, knocking the ball off the end of the bone, so its an easy fix according to the propaganda they are telling us, but she's in considerable pain none-the-less. So when she does come home, I expect to be a bit busier caring for her than I have been. I've been dreading this because she has absolutely no padding to absorb a fall. Anyplace. I'd have to hide several boxes of 30-06 ammo in her jeans to get the scales above 85 lbs. I'll speak up when I have the time & giddy-up. I'd gladly give her some of my excess padding, but thats not how it works. Thanks for all the help. But like a hungry puppy, I'll still be here. > > Thanks, > > Andrew > > -------------------------------------------------------------------- > >-- -------- Check out the vibrant tech community on one of the > > world's most engaging tech sites, SlashDot.org! > > http://sdm.link/slashdot > > _______________________________________________ > > Emc-users mailing list > > [email protected] > > https://lists.sourceforge.net/lists/listinfo/emc-users > > Cheers, Gene Heskett Cheers, Gene Heskett -- "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order." -Ed Howdershelt (Author) Genes Web page <http://geneslinuxbox.net:6309/gene> ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, SlashDot.org! http://sdm.link/slashdot _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, SlashDot.org! http://sdm.link/slashdot _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
