the daughter board is made by us, this is not of the firmware recommended by mesa
El mar., 24 de jul. de 2018 a la(s) 16:09, Peter C. Wallace (p...@mesanet.com) escribió: > On Tue, 24 Jul 2018, yomin estiven jaramillo munera wrote: > > > Date: Tue, 24 Jul 2018 16:02:05 -0500 > > From: yomin estiven jaramillo munera <yejm...@gmail.com> > > Reply-To: "Enhanced Machine Controller (EMC)" > > <emc-users@lists.sourceforge.net> > > To: emc-users@lists.sourceforge.net > > Subject: Re: [Emc-users] parallel ports configuration > > > > Hi, we have observed that we must configurate de firmware from xilinx is > this correct?, is there way of doing the configuration of the firmware of > another way?, is possible do it from pncconf? > > > Firmware is loaded with the utility "mesaflash" that loads bitfiles into > the > 5I25s memory > > > The breakout board/daughterboard pinout is needed to determine the proper > firmware to load. This is why I asked about the breakout board you are > using. > > > El mar., 24 de jul. de 2018 a la(s) 15:37, yomin estiven jaramillo munera ( > yejm...@gmail.com) escribiяя: > > > Debug file information: > > ./prueba.hal:51: parameter or pin 'hm2_5i25.0.stepgen.00.dirsetup' not > > found > > 6464 > > PID TTY STAT TIME COMMAND > > Stopping realtime threads > > Unloading hal components > > > > El mar., 24 de jul. de 2018 a la(s) 15:10, Peter C. Wallace ( > > p...@mesanet.com) escribiяя: > > > >> On Tue, 24 Jul 2018, yomin estiven jaramillo munera wrote: > >> > >> > Date: Tue, 24 Jul 2018 15:02:31 -0500 > >> > From: yomin estiven jaramillo munera <yejm...@gmail.com> > >> > Reply-To: "Enhanced Machine Controller (EMC)" > >> > <emc-users@lists.sourceforge.net> > >> > To: emc-users@lists.sourceforge.net > >> > Subject: Re: [Emc-users] parallel ports configuration > >> > > >> > Hi, i have problems for the pc recognize the card 5i25, i am trying to > >> >start from pncconf but when i execute linuxcnc, this sends me a error > >> which > >> >It seems to be card recognition, I am installing the card and > immediately > >> >making the configuration with pncconf, what am i not doing? > >> > >> > >> Can you copy the error message into a email? > >> > >> > >> > >> Peter Wallace > >> Mesa Electronics > >> > >> > >> > >> > >> > ------------------------------------------------------------------------------ > >> Check out the vibrant tech community on one of the world's most > >> engaging tech sites, Slashdot.org! http://sdm.link/slashdot > >> _______________________________________________ > >> Emc-users mailing list > >> Emc-users@lists.sourceforge.net > >> https://lists.sourceforge.net/lists/listinfo/emc-users > >> > > > > ------------------------------------------------------------------------------ > Check out the vibrant tech community on one of the world's most > engaging tech sites, Slashdot.org! http://sdm.link/slashdot > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > > Peter Wallace > Mesa Electronics > > (\__/) > (='.'=) This is Bunny. Copy and paste bunny into your > (")_(") signature to help him gain world domination. > > ------------------------------------------------------------------------------ > Check out the vibrant tech community on one of the world's most > engaging tech sites, Slashdot.org! http://sdm.link/slashdot > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
