Peter, Now the jumpers are as follows: 5i25 W1-Down, W2-Up, W3-Up, W4-Up, and W5-Up 7i76 W1-Left, W2-Left, W3-Left, W4-Left, W5-Left and W6-Left and the separate 5V supply is disconnected.
However, now the 5V LED is off. Alan > On Aug 23, 2018, at 4:38 PM, Peter C. Wallace <p...@mesanet.com> wrote: > > On Thu, 23 Aug 2018, Condit Alan wrote: > >> Date: Thu, 23 Aug 2018 13:50:05 -0700 >> From: Condit Alan <condita...@yahoo.com> >> To: Wallace Peter C. <p...@mesanet.com> >> Cc: "Emc-users@lists.sourceforge.net" <emc-users@lists.sourceforge.net>, >> andy pugh <bodge...@gmail.com> >> Subject: Re: [Emc-users] pncconf error under 2.7.14 >> I have attached the output from mesaflash. I have 4 or 5 25pin m-m cables. I >> have tried 3 different ones (new out of the bag (however made in china)). >> >> W1 is right, W3 is left. I just noticed that the 5V LED is pulsing bright >> then dim about every three seconds. > > > Normally W1 must be in the left hand position (this is likely why its not > working) > > Also sounds like you have a problem with your 5V power supply > > I would jumper the 5I25 /7I76 for cable power and eliminate the external 5V > supply as a potential issue: 7I76 W2 left, 5I25 W2 UP > >> >> >> >>> On Aug 23, 2018, at 10:57 AM, Peter C. Wallace <p...@mesanet.com> wrote: >>> >>> On Thu, 23 Aug 2018, Condit Alan wrote: >>> >>>> Date: Thu, 23 Aug 2018 10:31:08 -0700 >>>> From: Condit Alan <condita...@yahoo.com <mailto:condita...@yahoo.com>> >>>> To: Wallace Peter C. <p...@mesanet.com <mailto:p...@mesanet.com>> >>>> Cc: "Emc-users@lists.sourceforge.net >>>> <mailto:Emc-users@lists.sourceforge.net>" <emc-users@lists.sourceforge.net >>>> <mailto:emc-users@lists.sourceforge.net>>, >>>> andy pugh <bodge...@gmail.com <mailto:bodge...@gmail.com>> >>>> Subject: Re: [Emc-users] pncconf error under 2.7.14 >>>> Peter, >>>> >>>> I have a separate 24V 2.5amp DIN rail power supply that powers fieldIO and >>>> a small pcb power supply (7805 plus a couple caps) that comes off of it to >>>> supply 5v power. I had the jumper in the wrong position for separate >>>> powers for field IO and separate 5v power. I changed that jumper. I was >>>> getting both oranges LEDs lit before and after the change, but could that >>>> have caused a problem? >>> >>> Its not likely but if you supply external 5V and you have the jumpers wrong >>> you can possibly damage the 5I25 card or the cable (thats why theres a >>> warning in the manual) That said, a 7805 is not likely to have enough >>> current to do any real damage >>> >>>> >>>> I checked all the other jumpers on both boards and everything is now >>>> correct. I have a short DB25M to DB25F ribbon cable to bring the 7i76 out >>>> to the back of the cabinet. I disconnected it and connected the 6ft 25pin >>>> DB25m to DB25m cable direct from the 5i25 to the 7i76 but no change in >>>> behavior. >>>> >>>> I noticed that in pncconf there are no tabs for TB2 or TB3. Also on TB4 >>>> there are no lines for SPINDLE-ENA or SPINDLE-DIR. Is that normal? >>> >>> I would not worry about pncconf at this point, if you have no 7I76 pins its >>> likely a hardware or firmware setup issue >>> >>> >>>> >>>> I bought the 5i25/7i76 pair directly from you so I assume that it has the >>>> correct firmware??? >>> >>> >>> I would check just to make sure >>> >>> sudo mesaflash --device 5i25 --readhmid >>> >>> Did you get the DB25 M-M cable from us also? >>> >>> >>> Are 7I76 W1 and W3 in the left hand positions? >>>> >>>> What else can I do? >>>> >>>> Alan >>>> >>> >>> Peter Wallace >>> Mesa Electronics >>> >>> (\__/) >>> (='.'=) This is Bunny. Copy and paste bunny into your >>> (")_(") signature to help him gain world domination. >> >> > > Peter Wallace > Mesa Electronics > > (\__/) > (='.'=) This is Bunny. Copy and paste bunny into your > (")_(") signature to help him gain world domination. > ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users