Yep just busy😂 About to retrofit another machine soon so will be posting more then.
On Sun, Sep 27, 2020, 12:41 PM John Dammeyer <jo...@autoartisans.com> wrote: > I signed on with a second ID so now for the most part I seem to be getting > two of each message which makes sense. If I were only getting one the it > would lie with my ISP. > > I guess everyone is just busy doing stuff. > John > > > > -----Original Message----- > > From: Chris Albertson [mailto:albertson.ch...@gmail.com] > > Sent: September-26-20 4:15 PM > > To: Enhanced Machine Controller (EMC) > > Subject: Re: [Emc-users] Small project and test email. > > > > The EMC list is still hosted on sourceforge. Is sourceforge still alive > > or is it now a zombie? Do they have any employees left? That could > > explain a technical issue like this > > > > On Sat, Sep 26, 2020 at 2:07 PM Scott Harwell via Emc-users < > > emc-users@lists.sourceforge.net> wrote: > > > > > I see 29 on 9/22 7 on 9/23 1 on 9/25 3 on 9/26 > > > I saw the same thing on 7/27 > > > Scott > > > > > > On Saturday, September 26, 2020, 11:45:02 AM CDT, John Dammeyer < > > > jo...@autoartisans.com> wrote: > > > > > > The forum archives show no messages for the 24th, my message on the > 25th > > > and yours on the 26th. > > > > > > So perhaps everyone is COIVD-19 locked down inside their house and > can't > > > make it out to the shop or their PC? > > > > > > John > > > > > > > -----Original Message----- > > > > From: dave engvall [mailto:dengv...@charter.net] > > > > Sent: September-26-20 9:29 AM > > > > To: emc-users@lists.sourceforge.net > > > > Subject: Re: [Emc-users] Small project and test email. > > > > > > > > I just checked the forum and it is alive and well. Something is > screwed > > > > up with the list. > > > > Dave > > > > > > > > > > > > On 9/24/20 11:05 PM, John Dammeyer wrote: > > > > > For me the list has been quiet but checking the forum web page > there > > > have been messages up to 23SEP2020. Not sure why I'm > > > > suddenly not receiving messages so I thought I'd try and post what > I've > > > been up to. > > > > > > > > > > John > > > > > > > > > > > > > > > > > > > > I needed a matrix to guide a razor blade to cut Silpad into 0.375" > x > > > 0.55" pieces. But how to repeatedly measure 0.55"? > > > > > > > > > > Machine something of course. Here's the end product in plywood. > Did > > > use metal engraving bit and metal mill. > > > > > http://www.autoartisans.com/mill/SilPad/SilPadMatrix.jpg > > > > > > > > > > Start with an AlibreDrawing with lines for engraving. > > > > > http://www.autoartisans.com/mill/SilPad/SilPadMatrixDrawing.jpg > > > > > > > > > > Then create the G-Code and get LinuxCNC, this time running on a > > > Raspberry Pi4, to control the mill. > > > > > http://www.autoartisans.com/mill/SilPad/SilPadMatrixLinuxCNC.jpg > > > > > > > > > > And away we go. > > > > > http://www.autoartisans.com/mill/SilPad/SilPadMatrixEngraving.jpg > > > > > > > > > > The end result with a coat of shellac looks good but the lines are > > > hard to see. > > > > > http://www.autoartisans.com/mill/SilPad/SilPadMatrixShellaced.jpg > > > > > > > > > > So after a few more coats of shellac and some sanding I sprayed a > blue > > > coat. Then after it had a short while to dry a bit I used a > > > > paper towel with laquer thinner to wipe off the blue coating but > leave > > > the paint in the lines. > > > > > > > > > > Next step. Cut the silpad into the rectangles and that worked > really > > > well. > > > > > cid:image003.jpg@01D69135.80AB1C00 > > > > > > > > > > > > > > > John > > > > > > > > > > > > > > > > > > > > _______________________________________________ > > > > > Emc-users mailing list > > > > > Emc-users@lists.sourceforge.net > > > > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > > > > > > > _______________________________________________ > > > > Emc-users mailing list > > > > Emc-users@lists.sourceforge.net > > > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > > > > > > > _______________________________________________ > > > Emc-users mailing list > > > Emc-users@lists.sourceforge.net > > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > _______________________________________________ > > > Emc-users mailing list > > > Emc-users@lists.sourceforge.net > > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > > > > -- > > > > Chris Albertson > > Redondo Beach, California > > > > _______________________________________________ > > Emc-users mailing list > > Emc-users@lists.sourceforge.net > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
