On the Pi4 I did the following sudo apt-get update sudo apt-get upgrade uname -a shows I'm still on 4.19.71-rt24-v71+ #4 SMP PREEMPT RT from Apr 30 2020 But the 2.8.1-shuttle pre release I was running has now updated to Axis 2.8.2
John > -----Original Message----- > From: R C [mailto:[email protected]] > Sent: June-27-21 4:40 PM > To: [email protected] > Subject: Re: [Emc-users] 2.8.2 Release > > Hi Andy, > > > is that an ISO?� I have been looking around at the linuxcnc.org website, > but don't see it. > > > Do you have a download url? > > > thanks, > > > Ron > > > > On 6/27/21 5:08 PM, andy pugh wrote: > > LinuxCNC 2.8.2 has been released. > > > > This is mainly a bugfix release, though it also adds a new HAL > > component ("sendkeys") for creating input device events from HAL pins. > > > > All users are encouraged to update. > > > > In addition there is a new RTAI kernel based on 4.19.195. This comes > > with a new version of RTAI 5.3. Both should be automatically installed > > with the 2.8.2-rt version of LinuxCNC. If you are using the ISO > > install or know that you are running the preempt-rt kernel this need > > not concern you. > > > > Thanks to the following contributors: alkabal Chris Morley damiodj > > Dewey Garrett elovalvo Greg Carl Hans Unzner H�vard Flaget Aasen john > > Kiall Mac Innes McCodie NhanPham Norbert Schechner Phillip Carter Rene > > Hopf Sascha Ittner > > > > The abridged changelog: > > > > gladevcp: Numerous Updates > > qtvcp -cam_align panel: allow selection of camera number > > gmoccapy_3_1_3_8 - many updates > > Typo correction Axis.py "Geometry reading" XYZBCUVW > XYZABCUVW > > Docs add info on loading halscope > > update 2.8 from master for xhc-whb04b-6 > > Merge pull request #1024 from kiall/2.8-axis-error-pin > > translations - fixed moccapy / gmoccapy errors > > Update hostmot2.9 > > Fix: update manual SSI > > Update abs_encoder.c > > add info on installing mesaflash > > rx_mode typo in hm2_uart_setup > > Docs: Many updates > > flipflop: Add an inverted output pin, like the classic D-type latch > > pncconf -fix inverting of steppers, in the tune axis test > > qtvcp -qtaxis: change controls for lathe configs > > pyui -fix commands for joints/axis changes > > Docs: Correct pin direction 14 in the parallel port docs > > gmoccapy_translations - new translation files > > interp_o_word.cc: mdi-opened files leak #1088 > > command.c: use consistent external offset epsilon > > sendkeys: A HAL component to send keystrokes and UI events > > plasmac: fix material verter for sheetcam update > > fix halcompile singleton option on userspace components > > pncconf -fix internal description of 7i73 mode 1 > > pncconf -fix sserial number when parcing XML > > pncconf -fix sserial channel number for the 7i96 > > Docs: Update URL to updated Pi SD card image. Also document limitations. > > Merge pull request #1052 from Hans470/2.8-restructure-hal-doc > > pncconf -many uodates > > Added new version of Raspberry Pi4 and Raspberry Pi 400 > > AXIS: Add an axisui.error pin > > qtvcp -qtDragon docs: add a bit of information about probing. > > Update near.comp add {} for syntax coherence > > PlasmaC: Many Updates > > hal_glib -fix check_for_modes always failing > > emccanon.cc GET_EXTERNAL_TOOL_SLOT hdl bogus request > > Revert bad change inside driver XHC-WHB04B-6 lcnc 2.8 > > > > > > > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
