On 10/25/23 11:17, Todd Zuercher wrote:
Peter,
Thanks, But is it even going to be worth the effort? Since I'm sure the
regular minimum pulse length signal is still going to at least work albeit with
some possible theoretical performance limitations. I may not even require step
rates beyond where this is a non-issue?
I've asked the drive manufacturer. See if they get back to me.
Please post when you do get a reply Todd.
Todd Zuercher
P. Graham Dunn Inc.
630 Henry Street
Dalton, Ohio 44618
Phone: (330)828-2105ext. 2031
-----Original Message-----
From: Peter Wallace <p...@mesanet.com>
Sent: Wednesday, October 25, 2023 10:36 AM
To: Enhanced Machine Controller (EMC) <emc-users@lists.sourceforge.net>
Subject: Re: [Emc-users] Mesa Step Pulses?
[EXTERNAL EMAIL] Be sure links are safe.
On Wed, 25 Oct 2023, Todd Zuercher wrote:
Date: Wed, 25 Oct 2023 12:22:40 +0000
From: Todd Zuercher <to...@pgrahamdunn.com>
Reply-To: "Enhanced Machine Controller (EMC)"
<emc-users@lists.sourceforge.net>
To: "Enhanced Machine Controller (EMC)"
<emc-users@lists.sourceforge.net>
Subject: [Emc-users] Mesa Step Pulses?
Hello,
It is my understanding that the step pulses generated by Mesa cards
are always the minimum pulse length set by for example
hm2_5i25.0.stepgen.00.steplen, only the space between the pulses is
varied by the step rate, is that correct?
I was reading the manual for the new drive I was planning to use in my
next build and see that the drive calls a preference of a 50% duty
cycle for step pulse inputs. I am guessing that it may have something
to do with how the drive's pulse filtering system works, such that for
maximum noise filtering and step reliability having the pulse length
be approximately equal to the step spacing gives the best results.
So my questions are; Would it be possible to make a Mesa card output
a 50% duty cycle step pattern instead of the current default pattern?
And would doing this even be worth the effort?
Its possible with a minor firmware change and LinuxCNC driver change to enable
the mode.
Todd Zuercher
P. Graham Dunn
Inc.<https://nam04.safelinks.protection.outlook.com/?url=http%3A%2F%2F
http://www.pgrahamdunn.com/%2Findex.php&data=05%7C01%7Ctoddz%40pgrahamdunn.com
%7Ce5da628e16d4477d2d4008dbd567e82f%7C5758544c573f47cebee96c3e0806fb43
%7C0%7C0%7C638338414483169698%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAw
MDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000%7C%7C%7C&sda
ta=Zwbdv69ESSXKwXR%2FvXYbyijq1wOtyar%2FYeCMJAr6fgg%3D&reserved=0>
630 Henry Street
Dalton, Ohio 44618
Phone: (330)828-2105ext. 2031
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://list/
s.sourceforge.net%2Flists%2Flistinfo%2Femc-users&data=05%7C01%7Ctoddz%
40pgrahamdunn.com%7Ce5da628e16d4477d2d4008dbd567e82f%7C5758544c573f47c
ebee96c3e0806fb43%7C0%7C0%7C638338414483169698%7CUnknown%7CTWFpbGZsb3d
8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C
3000%7C%7C%7C&sdata=f1ssQLGo0gn0%2B2tjHAUXLZOjfsSHNrJWTjJDkkDRuAA%3D&r
eserved=0
Peter Wallace
Mesa Electronics
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
.
Cheers, Gene Heskett.
--
"There are four boxes to be used in defense of liberty:
soap, ballot, jury, and ammo. Please use in that order."
-Ed Howdershelt (Author, 1940)
If we desire respect for the law, we must first make the law respectable.
- Louis D. Brandeis
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
