ehre is the dmesg.. there is nothing in /var/log/messages at all which is
signifigant. (no errors) the box just dies with no errors:
I'll find isapnpdump and run that as well next msg
Linux version 2.2.10-33mdk ([EMAIL PROTECTED]) version pgcc-2.91.66
19990314 (egcs-1.1.2 release)) #1 Sat Jul 17 14:46:18 CDT 1999
Detected 300689413 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 299.83 BogoMIPS
Memory: 257720k/262080k available (1044k kernel code, 412k reserved, 2832k
data, 72k init)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Pentium II (Klamath) stepping 03
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35 (19990512) Richard Gooch ([EMAIL PROTECTED])
PCI: PCI BIOS revision 2.10 entry at 0xf0550
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
Initializing RT netlink socket
Starting kswapd v 1.5
Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
Uniform Multi-Platform E-IDE driver Revision: 6.20
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
PDC20246: IDE controller on PCI bus 00 dev 60
PDC20246: not 100% native mode: will probe irqs later
PDC20246: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
ide2: BM-DMA at 0xa000-0xa007, BIOS settings: hde:DMA, hdf:DMA
ide3: BM-DMA at 0xa008-0xa00f, BIOS settings: hdg:DMA, hdh:DMA
hda: QUANTUM FIREBALL EX12.7A, ATA DISK drive
hdb: QUANTUM FIREBALL EX12.7A, ATA DISK drive
hdc: Maxtor 91728D8, ATA DISK drive
hdd: Maxtor 91728D8, ATA DISK drive
hde: QUANTUM FIREBALL EL10.2A, ATA DISK drive
hdf: Maxtor 91728D8, ATA DISK drive
hdg: IBM-DTTA-351680, ATA DISK drive
hdh: QUANTUM FIREBALL EX12.7A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xb400-0xb407,0xb006 on irq 11
ide3 at 0xa800-0xa807,0xa406 on irq 11
hda: QUANTUM FIREBALL EX12.7A, 12159MB w/418kB Cache, CHS=1550/255/63
hdb: QUANTUM FIREBALL EX12.7A, 12159MB w/418kB Cache, CHS=1550/255/63
hdc: Maxtor 91728D8, 16479MB w/512kB Cache, CHS=33483/16/63
hdd: Maxtor 91728D8, 16479MB w/512kB Cache, CHS=33483/16/63
hde: QUANTUM FIREBALL EL10.2A, 9787MB w/418kB Cache, CHS=19885/16/63
hdf: Maxtor 91728D8, 16479MB w/512kB Cache, CHS=33483/16/63
hdg: IBM-DTTA-351680, 16124MB w/462kB Cache, CHS=32760/16/63
hdh: QUANTUM FIREBALL EX12.7A, 12159MB w/418kB Cache, CHS=24704/16/63
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
linear personality registered
raid0 personality registered
scsi: ***** BusLogic SCSI Driver Version 2.1.15 of 17 August 1998 *****
scsi: Copyright 1995-1998 by Leonard N. Zubkoff <[EMAIL PROTECTED]>
scsi0: Configuring BusLogic Model BT-958 PCI Wide Ultra SCSI Host Adapter
scsi0: Firmware Version: 5.06I, I/O Address: 0xB800, IRQ Channel: 10/Level
scsi0: PCI Bus: 0, Device: 11, Address: 0xE1800000, Host Adapter SCSI ID:
7
scsi0: Parity Checking: Enabled, Extended Translation: Enabled
scsi0: Synchronous Negotiation: FUUUUUU#UUUUUUUU, Wide Negotiation:
Enabled
scsi0: Disconnect/Reconnect: Enabled, Tagged Queuing: Enabled
scsi0: Scatter/Gather Limit: 128 of 8192 segments, Mailboxes: 211
scsi0: Driver Queue Depth: 211, Host Adapter Queue Depth: 192
scsi0: Tagged Queue Depth: Automatic, Untagged Queue Depth: 3
scsi0: Error Recovery Strategy: Default, SCSI Bus Reset: Enabled
scsi0: SCSI Bus Termination: Both Enabled, SCAM: Enabled, Level 1
scsi0: *** BusLogic BT-958 Initialized Successfully ***
scsi0 : BusLogic BT-958
scsi : 1 host.
Vendor: SEAGATE Model: ST39175LW Rev: 0001
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 15, lun 0
scsi0: Target 15: Queue Depth 28, Wide Synchronous at 40.0 MB/sec, offset 15
scsi : detected 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17783240 [8683 MB] [8.7
GB]
Partition check:
sda: sda1
hda: hda1 hda2 hda3
hdb: hdb1 hdb2
hdc: hdc1
hdd: hdd1
hde: hde1
hdf: hdf1
hdg: hdg1
hdh: hdh1
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 72k freed
Adding Swap: 136548k swap-space (priority -1)
scsi0: Tagged Queuing now active for Target 15
> We might get a better understanding if we saw your syslog from the crash
as
> well as your dmesg. And if it is a hardware problem, the other thing I
> would do is run a isapnpdump and configure your hardware. The Lothar team
> has a good program for setting your hardware and such but it is still in
> the testing phase.
