On Sat, 2003-06-21 at 06:42, Larry Sword wrote:Well if you only have the one cd-writer attached to the system:
richard bown wrote:
Hi Larry, read your mail , unticked the "on the fly box" and action
and then it did this
Wrote 17 of 24 MB.
?: Input/output error. : scsi sendcmd: no error
CDB: 2A 00 FF FF F1 E3 00 00 1A 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 71 00 04 00 00 00 00 0C 00 00 00 00 91 41 00 00
Sense Key: 0x4 Hardware Error, deferred error, Segment 0
Sense Code: 0x91 Qual 0x41 (vendor unique sense code 0x91) [No matching
qualifier] Fru 0x0
Sense flags: Blk 0 (not valid) cmd finished after 4.114s timeout 20s
ERROR: Write data failed.
ERROR: Writing failed.
so its a string of monosyllabic four letter words. I wonder if I've got a duff cdrw, as there's a hardware error.
any thoughts ??
Richard
Well to check the cdrw I returned it to the shop, with the printout
showing a hardware error, so got a new one ,,,and its the same :)
For ARTEC it seem to be generic-mmc-rawHow do you have the Settings -> Configure K3b Devices set? Under the Writer for "Cdrdao driver: ?? . I have mine set as "generic-mmc".
## Plus, I don't think this will make any difference, have the Dvd settings as a hdd=ide-scsi.
yup did that
During setup the program added the following stanza in my /etc/fstab file:
# /dev/scsi/host0/bus0/target0/lun0/cd /mnt/cdrecorder auto ro,noauto,user,exec 0 0
Umm just looked at my fstab
K3b setup has made a right mess of it !
ev/hda1 / ext3 defaults 1 1
none /dev/pts devpts mode=0620 0 0
/dev/hda6 /home ext3 defaults 1 2
none /mnt/cdrom supermount
dev=/dev/hdd,fs=auto,ro,--,iocharset=iso8859-15,codepage=850 0 0
none /mnt/cdrom2 supermount
dev=/dev/scd0,fs=auto,ro,--,iocharset=iso8859-15,codepage=850 0 0
none /mnt/floppy supermount
dev=/dev/fd0,fs=auto,--,iocharset=iso8859-15,sync,codepage=850 0 0
/dev/hda7 /music ext3 defaults 1 2
none /proc proc defaults 0 0
/dev/hda8 /video ext3 defaults 1 2
/dev/hda5 swap swap defaults 0 0
/dev/scsi/host0/bus0/target3/lun0/cd /mnt/cdrecorder auto ro,noauto,user,exec 0 0
/dev/scsi/host1/bus0/target0/lun0/cd /mnt/cdrecorder auto ro,noauto,user,exec 0 0
Well I only have 1 cd drive on the machine at the moment which is the
cdrw, As I have scsi emulation do I need the dev/hdd line in ?, the last line
can go as its a duplicate
Hmmm point us in the right direction on this
TIA
Richard
1. Make and save a copy of the fstab.
2. Remove the all lines added by k3b.
3. Remove the supermount lines for /dev/hdd.
4. Modify the /etc/lilo.conf and ensure that only the correct append statement for the one cd-writer in indicated: hdc=ide-scsi???
5. Run lilo to install (as Root).
6. Reboot machine. If a clean reboot run "cdrecord -scanbus" to virify the correct info fot the cd-writer.
7. Ensure that the stanza the /etc/fstab is correct and pointing to the right link.
Correct as necessary.
8. Try running a data cd in the writer to ensure it reads okay.
9. Re-run the K3b Setup program. 10. Check the /etc/fstab to verify thre correct stanza added. 11. Run K3b and change the correct cdrdao in installed... 12. Burn Burn
Larry
Want to buy your Pack or Services from MandrakeSoft? Go to http://www.mandrakestore.com
