<Grin>
Depending on the height of your firewall, assuming the standard 7 foot rack,
Wouldn't it be easier to simply throw your Cat 5 cable over the top of the
firewall and simply plugin to the ISP router? In this way bypassing those
silly university people all tyogether(sp?) <grin/>
Funny Stuff!
Ken
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]]On Behalf Of "J"
Sent: Wednesday, July 11, 2001 3:39 AM
To: [EMAIL PROTECTED]
Subject: RE: Hacking FW-1 programs
Well, for the determined of spirit, I offer the following advice:
A firewall is a difficult thing to "get through." First off, most good ones
are made of heat-molded concrete with a ludicrously high grain-count, so
just the outer layer is going to be hard to get through. See, the challenge
is to generate enough heat in one concentrated region so the fine-grain of
the concrete shell begin to melt together into an oily sludge. This is a
sign things are going well. Additionally, the sludge will help keep the
drill-bits cool.
Now, at this point, many seasoned professionals will recommend
diamond-tipped drill bits. I however, being a beliver in modern technology,
prefer the tungsten-carbide bits. While you do replace more of them during
an operation, I find they wear predictably and provide a better conduit-area
for your needs.
Next, you'll have to contend with a re-enforced aluminium-carbon sink-plate.
The reason for this layer is to distribute the heat from the outer walls of
the firewall to something else; in most cases, foundation beams in the
building, sending the heat into the surrounding foundation. The
compressed-aluminium will get your tungsten bits very, very hot. I'd also
recommend wearing ear protection at this point. Be aware that dogs will
start barking for miles around when you hit this layer.
Once through the heat-sink, you're faced with one of two typical
possibilities: ceramic interior or polycarbonate-platter walls. If you find
ceramic, you're in luck, because the ceramic will withstand the pressure of
the explosives you'll be using later. The platters, however, are another
ball game. All I'll say is: bring a DustBuster!
Providing you've come up 7's on the ceramic, you should go ahead and stuff
as much plastic-explosive as you can in the hole you've drilled (which was
3" diameter, right?). Most experts, and I concur with them this time, prefer
to use Primacord as the detonation device. I've heard of a few nice tricks
with wrapping the Prima around the firewall to help "cut" the outer concrete
shell and shatter the wall itself.
Step 10: Blow up firewall.
If you followed the above steps, you should now have, after the dust
settles, a pathway through the firewall into the inner-room that you should
be able to walk or crouch through. Grab your spool of CAT5 cable, and tow a
lead behind you as you walk through your new hole in the firewall. Once
inside, crimp the end of the cable you're holding with a standard RJ45
connector. Take note of the order the colored-wires are in: you'll need to
make the other end the same way. Plug into edge router or switch.
Walk back to spool. Count out about twenty feet of cable, and cut. Crimp
another RJ45 connector on this end, taking care to align the little
colored-wires in the same order as the first end, and plug into your
computer.
I guarantee the firewall will not interrupt any traffic on your line.
Hope this helps,
J
Cheers!
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]]On Behalf Of MNR. E DE BEER
Sent: Tuesday, July 10, 2001 8:00 PM
To: [EMAIL PROTECTED]
Subject: Hacking FW-1 programs
Are there any Hack software that I can use to get access to a
Firewall-1 without using Inetkey (username and password)?
Where can I find this softwhere?
_______________________________________________
Firewalls mailing list
[EMAIL PROTECTED]
http://lists.gnac.net/mailman/listinfo/firewalls
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]]On Behalf Of MNR. E DE BEER
Sent: Tuesday, July 10, 2001 8:00 PM
To: [EMAIL PROTECTED]
Subject: Hacking FW-1 programs
Are there any Hack software that I can use to get access to a
Firewall-1 without using Inetkey (username and password)?
Where can I find this softwhere?
_______________________________________________
Firewalls mailing list
[EMAIL PROTECTED]
http://lists.gnac.net/mailman/listinfo/firewalls
_______________________________________________
Firewalls mailing list
[EMAIL PROTECTED]
http://lists.gnac.net/mailman/listinfo/firewalls
_______________________________________________
Firewalls mailing list
[EMAIL PROTECTED]
http://lists.gnac.net/mailman/listinfo/firewalls
