I'm using a Raspberry Pi Zero and SOIC clip to communicate with a MX25L12873F chip, using flashrom built from master branch (1b1066e).
Reading the chip is working fine, no matter how many times I do a read operation, the resulting firmware image is correct. However, I'm unable to write to the chip: ======================================================================== flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=1000 -c \ MX25L12833F/MX25L12835F/MX25L12845E/MX25L12865E/MX25L12873F \ -w firmware.bin --ifd -i fd -i bios -i me --noverify-all -VVV -o out.log Initializing linux_spi programmer Using device /dev/spidev0.0 Using 1000kHz clock get_max_kernel_buf_size: Using value from \ /sys/module/spidev/parameters/bufsiz as max buffer size. linux_spi_init: max_kernel_buf_size: 4096 The following protocols are supported: SPI. Probing for Macronix \ MX25L12833F/MX25L12835F/MX25L12845E/MX25L12865E/MX25L12873F, \ 16384 kB: programmer_map_flash_region: mapping \ MX25L12833F/MX25L12835F/MX25L12845E/MX25L12865E/MX25L12873F from \ 0xff000000 to 0x00000000 RDID returned 0xc2 0x20 0x18. compare_id: id1 0xc2, id2 0x2018 Added layout entry 00000000 - 00ffffff named complete flash Found Macronix flash chip \ "MX25L12833F/MX25L12835F/MX25L12845E/MX25L12865E/MX25L12873F" \ (16384 kB, SPI) on linux_spi. Chip status register is 0x7c. Chip status register: Status Register Write Disable (SRWD, SRP, ...) \ is not set Chip status register: Bit 6 is set Chip status register: Block Protect 3 (BP3) is set Chip status register: Block Protect 2 (BP2) is set Chip status register: Block Protect 1 (BP1) is set Chip status register: Block Protect 0 (BP0) is set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set programmer_unmap_flash_region: unmapped 0x00000000 This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to \ completely clone the contents of this chip (see man page for details). programmer_map_flash_region: mapping \ MX25L12833F/MX25L12835F/MX25L12845E/MX25L12865E/MX25L12873F from \ 0xff000000 to 0x00000000 Some block protection in effect, disabling... \ Block protection could not be disabled! Chip status register is 0x7c. Chip status register: Status Register Write Disable (SRWD, SRP, ...) \ is not set Chip status register: Bit 6 is set Chip status register: Block Protect 3 (BP3) is set Chip status register: Block Protect 2 (BP2) is set Chip status register: Block Protect 1 (BP1) is set Chip status register: Block Protect 0 (BP0) is set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Reading ich descriptor... done. layout_from_ich_descriptors():1367, returned with value -1. Couldn't parse the descriptor! Illegal instruction ======================================================================== On an identical system, I have been using the flashrom internal programmer to write the same firmware image without any errors parsing the descriptor. Any ideas why this happens? I'm a doing something wrong? Thanks. Best regards, Pete Smith _______________________________________________ flashrom mailing list -- flashrom@flashrom.org To unsubscribe send an email to flashrom-le...@flashrom.org
