I really don't think that a traditional "roofing filter" would help out the 
FLEX 5000's, but what might be an interesting idea would be a very tight "RF 
Preselector" like we use to use in the fixed military HF sites around the 
world.  The preselector is basically a very tight HF Filter at the actual 
operating frequency.  Collins used these with their HF 80 series receivers.    
I currently use a Harris surplus military preselector in my receive loop and it 
makes a world of difference on my Flex 5000A.  I've got it set up to allow 3Khz 
up and down from my actual center frequency and everything else is 40db down.  
A preselector won't help in removing close noise, like 1 or 2kc's away, but it 
does get rid off all of the funky things on the screen from extremely strong 
stations and stations outside of the 6Khz bandwidth that are putting out dirty 
signals and splattering all over the place or if your operating multiple 
stations from the same location on the same band.  The only problem with using 
a Harris preselector, is it does not follow the operating frequency 
automatically, so if you change frequencies, you must also manually tune the 
preselector.  The other issue that I see with a preselector the way I have it 
installed in the Receive loop, where you would normally put a pre-amp, is I 
don't see any signals on the screen outside of my 6 Khz, but I normally just 
park it on a frequency and work DX and don't run up and down the band much, 
when I'm operating.  But for a newly designed preselector it would be possible 
for the receive RF to be displayed on the screen, while the rf was routed to 
the preselector.  In the past preselectors where big, bulky and expensive.  I 
paid over $600.00 for my surplus Harris, but it was totally clean and 
operational, but I do run 2 to 3 operating positions sometimes, so it was well 
worth it.

73's,

Mike
KE7WRJ 


--- [email protected] wrote:

From: <[email protected]>
To: "Joe Roth-WC4R" <[email protected]>,    "flexradio" <[email protected]>
Subject: Re: [Flexradio] Roofing filter
Date: Fri, 31 Jul 2009 14:52:49 +0200

Hello Joe,
my 2 (Euro) cents
 

What is (the function of) a roofing filter, see next 2 links:

- http://www.qth.com/inrad/roofing-filters.pdf
"A few words about intermodulation dynamic range and roofing filters"

- http://wapedia.mobi/en/Roofing_filter
"A roofing filter is a type of filter used in a HF 
<https://netmail.hetnet.nl/en/High_frequency>  receiver ( shortwave 
<https://netmail.hetnet.nl/en/Shortwave>  radio 
<https://netmail.hetnet.nl/en/Radio>  ). It is usually 
found after the first receiver mixer. The goal of a roofing filter is to reduce 
the passband <https://netmail.hetnet.nl/en/Passband>  
of the 1st intermediate frequency (IF) to about 6-20 kHz 
<https://netmail.hetnet.nl/en/Hertz>  , so that overloading and 
distortions by the following amplifier <https://netmail.hetnet.nl/en/Amplifier> 
 stages and mixers are reduced"

In the FLEX tranceivers the 1st receiver mixer is followed by an A/D converter 
(with anti-aliasing filter). The only passband filtering following this is in 
software 
and determines the passband with "brick-wall filtering". This filter is the 
roofing filter and final filter in one.

It is a VARIABLE (both in a bit in center frequency and bandwith) "roofing 
filter"
it does not need additional hardware.

Care must be taken not to overload the 1stmixer + A/D converter. 
No problem in the FLEX frontends with their hi dynamic range 

73s Peter pa0pvn
 
groeten Peter          website    http://www.homepages.hetnet.nl/~petervn/ 
<https://netmail.hetnet.nl/exchweb/bin/redir.asp?URL=http://www.homepages.hetnet.nl/~petervn/>
         
petervn-at-hetnet-nl  pa0pvn-at-hetnet-nl  pa0pvn-at-amsat-org
only large files:        pa0pvn-at-gmail-com
There are 10 kind of people, those who can count to 1010 on their fingers,
and those who count to 1111111111.
 

________________________________

Van: [email protected] namens Joe Roth-WC4R
Verzonden: vr 31-7-2009 2:53
Aan: 'flexradio'
Onderwerp: [Flexradio] Roofing filter






I read why the Flex 5000 does not use a roofing filter somewhere. As I
recall it was due to the RX design. I can't find that info now and I would
like to find out exactly why roofing filters do not have a place in the
5000/3000.

Thanks, Joe



www.rothweb.net

www.WilliamsburgWX.com

www.wc4r.com



_______________________________________________
FlexRadio Systems Mailing List
[email protected]
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to [email protected]


_______________________________________________
FlexRadio Systems Mailing List
[email protected]
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to [email protected]


_______________________________________________
FlexRadio Systems Mailing List
[email protected]
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to [email protected]

Reply via email to