You are running the router (L3) code. That's why the commands aren't there. On the L3 code addresses are configured on interfaces directly. Also "ip policy" becomes "ip l4-policy" on L3 code.
"Compiled on Sep 04 2008 at 19:17:10 labeled as WXR10201c" See "WXR" above - the R indicates routing code. I would strongly suggest if you don't have the L3 upgrade in your SI that you obtain the switch code and load that on. Regards, Patrick ________________________________________ From: [email protected] [[email protected]] On Behalf Of Samit [[email protected]] Sent: Thursday, March 12, 2009 10:16 PM To: [email protected] Subject: [f-nsp] Unrecognized command Hi, Spend half day without a luck to do a basic configuration of TCS in pure L2 environment in my recently arrived ServerIronGT EGx2. I am following this guide http://www.foundrynetworks.co.jp/services/documentation/siug/ServerIron_Cache_Switching.html#5936 Along with ServerIron_10200_xxxx Guides.. But I am stuck here...with "Unrecognized command" so cannot move forward... ServerIron(config)#ip address Unrecognized command ServerIron(config)#ip address Unrecognized command ServerIron(config)#ip de default-network Configure default network route ServerIron(config)#ip default-gate Unrecognized command ServerIron(config)#ip default-gate Unrecognized command ServerIron(config)#ip po. Unrecognized command ServerIron(config)#ip poli policy Enable policy routing ServerIron(config)#ip policy prefer-direct-route Use direct route preference route-map Policy route map ServerIron(config)#ip policy 2 ca Unrecognized command ServerIron(config)#ip policy 2 cache Unrecognized command ServerIron(config)# ServerIron#sh ver SW: Version 10.2.01cTD4 Copyright (c) 1996-2007 Foundry Networks, Inc. Compiled on Sep 04 2008 at 19:17:10 labeled as WXR10201c HW: ServerIronGT E-1 Router, SYSIF version 21, Serial #: Non-exist ========================================================================== SL 1: B0GMR WSM6 Management Module, SYSIF 2, M6, ACTIVE Serial #: CH50050124 0 MB SHM, 1 Application Processors 16384 KB BRAM, SMC version 5, BM version 21 SW: (1)10.2.01cTF2 ========================================================================== SL 2: J-BxG JetCore Gig Fiber Module, SYSIF 2 (Mini GBIC) Serial #: PR13021751 4096 KB BRAM, JetCore ASIC IGC version 49, BIA version 89 32768 KB PRAM and 2M-Bit*1 CAM for IGC 4, version 0449 32768 KB PRAM and 2M-Bit*1 CAM for IGC 5, version 0449 ========================================================================== Active management module: 1.0 GHz Power PC processor 750GX (version 7002/0102) 66 MHz bus 512 KB boot flash memory 16384 KB code flash memory 512 KB SRAM 512 MB DRAM The system uptime is 3 hours 24 minutes 6 seconds Really appreciate if anyone can shed some light in this and help me with some tips to configure the TCS. Lan/Router<-->ServerIronGT<-->Wan/Router | Web Proxy Farm Regards, Samit _______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp ************************************************************************ *PLEASE NOTE* This email and any attachments may be confidential. If received in error, please delete all copies and advise the sender. The reproduction or dissemination of this email or its attachments is prohibited without the consent of the sender. WARNING RE VIRUSES: Our computer systems sweep outgoing email to guard against viruses, but no warranty is given that this email or its attachments are virus free. Before opening or using attachments, please check for viruses. Our liability is limited to the re-supply of any affected attachments. Any views expressed in this message are those of the individual sender, except where the sender expressly, and with authority, states them to be the views of the organisation. ************************************************************************ _______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp
