Upgrading to 5.1.00b should fix this problem.
Closed defects in IronWare R05.1.00b for the FastIron X Series Switches 106289 Critical Summary: 10 GbE ports may not link up. Symptom: No link on 10 GbE ports Probability: Medium Feature: System Function: System Jared Valentine [email protected] From: [email protected] [mailto:[email protected]] On Behalf Of Chuck Ufarley Sent: Wednesday, September 30, 2009 12:58 PM To: [email protected] Subject: [f-nsp] Port State Blocking, FastIron SX 800 Hi all-- I've got an FI-SX 800 with a FI-2XGMR4 PREM and a couple of FI-42XGs, and I can't seem to get the ports on the 2XGs to come up. There's nothing connected to the box at all. Reloads and power downs keep repeating a port state BLOCKING. Can't figure out why. Console output is below. Anyone got any advice? FastIron SX 800 Router#sho run Current configuration: ! ver 05.1.00T3e3 ! module 1 fi-sx4-2-port-10g-module module 2 fi-sx4-2-port-10g-module module 9 fi-sx4-2-10g-port-management-module ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! end FastIron SX 800 Router#sho ver ========================================================================== Active Management CPU [Slot-9]: SW: Version 05.1.00T3e3 Copyright (c) 1996-2009 Brocade Communications Systems , Inc. Compiled on May 12 2009 at 22:13:55 labeled as SXR05100 (3395303 bytes) from Primary SXR05100.bin BootROM: Version 05.1.00T3e5 (FEv2) Serial #: SA17085232 HW: Chassis FastIron SX 800-PREM (PROM-TYPE SX-FIL3U) ========================================================================== SL 1: SX-FI42XG 2-port 10G Serial #: CH05080069 P-ASIC 0: type 01D1, rev 00 subrev 00 P-ASIC 1: type 01D1, rev 00 subrev 00 ========================================================================== SL 2: SX-FI42XG 2-port 10G Serial #: CH05080080 P-ASIC 2: type 01D1, rev 00 subrev 00 P-ASIC 3: type 01D1, rev 00 subrev 00 ========================================================================== SL 9: SX-FI2XGMR4 2-port Management Serial #: CH34070027 P-ASIC 16: type 01D1, rev 00 subrev 00 P-ASIC 17: type 01D1, rev 00 subrev 00 ========================================================================== Active Management Module: 660 MHz Power PC processor 8541 (version 32/0020) 66 MHz bus 512 KB boot flash memory 16384 KB code flash memory 512 MB DRAM The system uptime is 22 minutes 9 seconds The system : started=cold start FastIron SX 800 Router#sho mod Module Status Ports Starting MAC F1: SX-FISF Switch Fabric active F2: SX-FISF Switch Fabric active S1: SX-FI42XG 2-port 10G OK 2 0012.f226.d700 S2: SX-FI42XG 2-port 10G OK 2 0012.f226.d718 S3: S4: S5: S6: S7: S8: S9: SX-FI2XGMR4 2-port Management Active 2 0012.f226.d7c0 { Status : OK } S10: Standby 0 FastIron SX 800 Router#sho int e 1/1 10GigabitEthernet1/1 is down, line protocol is down Hardware is 10GigabitEthernet, address is 0012.f226.d700 (bia 0012.f226.d700) Configured speed 10Gbit, actual unknown, configured duplex fdx, actual unknown Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING BPDU guard is Disabled, ROOT protect is Disabled Link Error Dampening is Disabled STP configured to ON, priority is level0 Flow Control is enabled mirror disabled, monitor disabled Not member of any active trunks Not member of any configured trunks No port name IPG XGMII 96 bits-time IP MTU 1500 bytes, encapsulation ethernet 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization 300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 multicasts, 0 unicasts 0 input errors, 0 CRC, 0 frame, 0 ignored 0 runts, 0 giants 0 packets output, 0 bytes, 0 underruns Transmitted 0 broadcasts, 0 multicasts, 0 unicasts 0 output errors, 0 collisions Relay Agent Information option: Disabled FastIron SX 800 Router#sho int e 1/2 10GigabitEthernet1/2 is down, line protocol is down Hardware is 10GigabitEthernet, address is 0012.f226.d701 (bia 0012.f226.d701) Configured speed 10Gbit, actual unknown, configured duplex fdx, actual unknown Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING BPDU guard is Disabled, ROOT protect is Disabled Link Error Dampening is Disabled STP configured to ON, priority is level0 Flow Control is enabled mirror disabled, monitor disabled Not member of any active trunks Not member of any configured trunks No port name IPG XGMII 96 bits-time IP MTU 1500 bytes, encapsulation ethernet 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 multicasts, 0 unicasts 0 input errors, 0 CRC, 0 frame, 0 ignored 0 runts, 0 giants 0 packets output, 0 bytes, 0 underruns Transmitted 0 broadcasts, 0 multicasts, 0 unicasts 0 output errors, 0 collisions Relay Agent Information option: Disabled FastIron SX 800 Router# As always, your help is greatly appreciated. Thanks. --Chuck
_______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp
