Didn't even know there was a 5100b. Unfortunately, I tried it and got the same result. Port state BLOCKING. Weirder still, the management port still immediately goes to FORWARDING, even if nothing's connected. Anyone experience that?
I tried downgrading to 4.2.00b, too, both SXS and SXR. Neither worked. Same blocking/forwarding issues. Thanks for the suggestion, though. --Chuck. On Wed, Sep 30, 2009 at 1:00 PM, Jared Valentine <[email protected]>wrote: > *Upgrading to 5.1.00b should fix this problem. * > > * * > > *Closed defects in IronWare R05.1.00b for the FastIron X Series Switches* > > *106289 Critical Summary*: 10 GbE ports may not link up. > > *Symptom*: No link on 10 GbE ports > > *Probability*: Medium > > *Feature*: System > > *Function*: System > > > > Jared Valentine > > [email protected] > > > > > > > > *From:* [email protected] [mailto: > [email protected]] *On Behalf Of *Chuck Ufarley > *Sent:* Wednesday, September 30, 2009 12:58 PM > *To:* [email protected] > *Subject:* [f-nsp] Port State Blocking, FastIron SX 800 > > > > Hi all-- > > I've got an FI-SX 800 with a FI-2XGMR4 PREM and a couple of FI-42XGs, and I > can't seem to get the ports on the 2XGs to come up. There's nothing > connected to the box at all. Reloads and power downs keep repeating a port > state BLOCKING. Can't figure out why. Console output is below. Anyone got > any advice? > > FastIron SX 800 Router#sho run > Current configuration: > ! > ver 05.1.00T3e3 > ! > module 1 fi-sx4-2-port-10g-module > module 2 fi-sx4-2-port-10g-module > module 9 fi-sx4-2-10g-port-management-module > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > end > > FastIron SX 800 Router#sho ver > > ========================================================================== > Active Management CPU [Slot-9]: > SW: Version 05.1.00T3e3 Copyright (c) 1996-2009 Brocade Communications > Systems > , Inc. > Compiled on May 12 2009 at 22:13:55 labeled as SXR05100 > (3395303 bytes) from Primary SXR05100.bin > BootROM: Version 05.1.00T3e5 (FEv2) > Serial #: SA17085232 > HW: Chassis FastIron SX 800-PREM (PROM-TYPE SX-FIL3U) > ========================================================================== > SL 1: SX-FI42XG 2-port 10G > Serial #: CH05080069 > P-ASIC 0: type 01D1, rev 00 subrev 00 > P-ASIC 1: type 01D1, rev 00 subrev 00 > ========================================================================== > SL 2: SX-FI42XG 2-port 10G > Serial #: CH05080080 > P-ASIC 2: type 01D1, rev 00 subrev 00 > P-ASIC 3: type 01D1, rev 00 subrev 00 > ========================================================================== > SL 9: SX-FI2XGMR4 2-port Management > Serial #: CH34070027 > P-ASIC 16: type 01D1, rev 00 subrev 00 > P-ASIC 17: type 01D1, rev 00 subrev 00 > ========================================================================== > Active Management Module: > 660 MHz Power PC processor 8541 (version 32/0020) 66 MHz bus > 512 KB boot flash memory > 16384 KB code flash memory > 512 MB DRAM > The system uptime is 22 minutes 9 seconds > The system : started=cold start > > FastIron SX 800 Router#sho mod > Module Status Ports Starting MAC > F1: SX-FISF Switch Fabric active > F2: SX-FISF Switch Fabric active > S1: SX-FI42XG 2-port 10G OK 2 > 0012.f226.d700 > S2: SX-FI42XG 2-port 10G OK 2 > 0012.f226.d718 > S3: > S4: > S5: > S6: > S7: > S8: > S9: SX-FI2XGMR4 2-port Management Active 2 > 0012.f226.d7c0 > { Status : OK } > S10: Standby 0 > FastIron SX 800 Router#sho int e 1/1 > 10GigabitEthernet1/1 is down, line protocol is down > Hardware is 10GigabitEthernet, address is 0012.f226.d700 (bia > 0012.f226.d700) > Configured speed 10Gbit, actual unknown, configured duplex fdx, actual > unknown > > Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING > BPDU guard is Disabled, ROOT protect is Disabled > Link Error Dampening is Disabled > STP configured to ON, priority is level0 > Flow Control is enabled > mirror disabled, monitor disabled > Not member of any active trunks > Not member of any configured trunks > No port name > IPG XGMII 96 bits-time > IP MTU 1500 bytes, encapsulation ethernet > 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization > 300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization > 0 packets input, 0 bytes, 0 no buffer > Received 0 broadcasts, 0 multicasts, 0 unicasts > 0 input errors, 0 CRC, 0 frame, 0 ignored > 0 runts, 0 giants > 0 packets output, 0 bytes, 0 underruns > Transmitted 0 broadcasts, 0 multicasts, 0 unicasts > 0 output errors, 0 collisions > Relay Agent Information option: Disabled > FastIron SX 800 Router#sho int e 1/2 > 10GigabitEthernet1/2 is down, line protocol is down > Hardware is 10GigabitEthernet, address is 0012.f226.d701 (bia > 0012.f226.d701) > Configured speed 10Gbit, actual unknown, configured duplex fdx, actual > unknown > > Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING > BPDU guard is Disabled, ROOT protect is Disabled > Link Error Dampening is Disabled > STP configured to ON, priority is level0 > Flow Control is enabled > mirror disabled, monitor disabled > Not member of any active trunks > Not member of any configured trunks > No port name > IPG XGMII 96 bits-time > IP MTU 1500 bytes, encapsulation ethernet > 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization > 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization > 0 packets input, 0 bytes, 0 no buffer > Received 0 broadcasts, 0 multicasts, 0 unicasts > 0 input errors, 0 CRC, 0 frame, 0 ignored > 0 runts, 0 giants > 0 packets output, 0 bytes, 0 underruns > Transmitted 0 broadcasts, 0 multicasts, 0 unicasts > 0 output errors, 0 collisions > Relay Agent Information option: Disabled > FastIron SX 800 Router# > > > As always, your help is greatly appreciated. > > Thanks. > > --Chuck >
_______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp
