Check the connected interfaces, see if there's crc errors, collisions, etc..
On 7/1/10 2:34 PM, DELOBEL Gary wrote:
I think all is ok on cam
tel...@br1-uro(config-bgp)#sh cam-part det
==== SLOT 1 CAM PARTITION ====
IGC: 0 (0x00)
Number of CAM devices per IGC: 1
Number of hw entries per CAM: 0x08000
Total size of CAM = 2Mbits
complete CAM index range per IGC:
(sw) 1 - 56319 (1 - 0x0dbff), total entries: 56319 (0x0dbff)
(hw) 0 - 32767 (0 - 0x07fff), total entries: 32768 (0x08000)
Percentage of CAM hardware entries for each partition:
Layer3 = 23552 (1.4375Mbits) (71.875%)
Level3 = 2047 (0.124938Mbits) (6.246948%)
Level2 = 2048 (0.125Mbits) (6.25%)
Layer2 = 1024 (0.0625Mbits) (3.125%)
Layer4 = 8192 (0.5Mbits) (25%)
Layer 3 sw index range:
L3 L3 1 - 4095 (0x00001 - 0x00fff), free 4026 (0x00fba)
L3 L2 4096 - 8191 (0x01000 - 0x01fff), free 3361 (0x00d21)
L3 8192 - 47103 (0x02000 - 0x0b7ff), free 27155 (0x06a13)
layer 3 hw index range (inversely mapped):
23551 - 0 (0x05bff - 0x00000)
L2 index range:
(sw) 47104 - 48127 (0x0b800 - 0x0bbff), free 879 (0x0036f)
(hw) 23552 - 24575 (0x05c00 - 0x05fff)
L4 pool 3 index range:
(sw) 48128 - 50687 (0x0bc00 - 0x0c5ff), free 2560 (0x00a00)
(hw) 24576 - 27135 (0x06000 - 0x069ff)
L4 pool 2 index range:
(sw) 50688 - 53247 (0x0c600 - 0x0cfff), free 2560 (0x00a00)
(hw) 27136 - 29695 (0x06a00 - 0x073ff)
L4 pool 1 index range:
(sw) 53248 - 55807 (0x0d000 - 0x0d9ff), free 2560 (0x00a00)
(hw) 29696 - 32255 (0x07400 - 0x07dff)
L4 pool 0 index range:
(sw) 55808 - 56319 (0x0da00 - 0x0dbff), free 504 (0x001f8)
(hw) 32256 - 32767 (0x07e00 - 0x07fff)
IGC: 1 (0x01)
Number of CAM devices per IGC: 1
Number of hw entries per CAM: 0x08000
Total size of CAM = 2Mbits
complete CAM index range per IGC:
(sw) 1 - 56319 (1 - 0x0dbff), total entries: 56319 (0x0dbff)
(hw) 0 - 32767 (0 - 0x07fff), total entries: 32768 (0x08000)
Percentage of CAM hardware entries for each partition:
Layer3 = 23552 (1.4375Mbits) (71.875%)
Level3 = 2047 (0.124938Mbits) (6.246948%)
Level2 = 2048 (0.125Mbits) (6.25%)
Layer2 = 1024 (0.0625Mbits) (3.125%)
Layer4 = 8192 (0.5Mbits) (25%)
Layer 3 sw index range:
L3 L3 1 - 4095 (0x00001 - 0x00fff), free 4095 (0x00fff)
L3 L2 4096 - 8191 (0x01000 - 0x01fff), free 4096 (0x01000)
L3 8192 - 47103 (0x02000 - 0x0b7ff), free 38512 (0x09670)
layer 3 hw index range (inversely mapped):
23551 - 0 (0x05bff - 0x00000)
L2 index range:
(sw) 47104 - 48127 (0x0b800 - 0x0bbff), free 993 (0x003e1)
(hw) 23552 - 24575 (0x05c00 - 0x05fff)
L4 pool 3 index range:
(sw) 48128 - 50687 (0x0bc00 - 0x0c5ff), free 2560 (0x00a00)
(hw) 24576 - 27135 (0x06000 - 0x069ff)
L4 pool 2 index range:
(sw) 50688 - 53247 (0x0c600 - 0x0cfff), free 2560 (0x00a00)
(hw) 27136 - 29695 (0x06a00 - 0x073ff)
L4 pool 1 index range:
(sw) 53248 - 55807 (0x0d000 - 0x0d9ff), free 2560 (0x00a00)
(hw) 29696 - 32255 (0x07400 - 0x07dff)
L4 pool 0 index range:
(sw) 55808 - 56319 (0x0da00 - 0x0dbff), free 504 (0x001f8)
(hw) 32256 - 32767 (0x07e00 - 0x07fff)
Le 01/07/2010 14:21, Jeroen Wunnink a écrit :
'sh cam-part det'
See if cam is filling up or nearly empty, dig the maillist archives
over the last few months a bit, been a whole discussion about cam
exhaustion
On 7/1/10 12:47 PM, DELOBEL Gary wrote:
Hi,
we have some loss on jetcore router (~10%) but cpu at 1% and memory
at 67%
undry-nsp
--
Met vriendelijke groet,
Jeroen Wunnink,
EasyHosting B.V. Systeembeheerder
[email protected]
telefoon:+31 (035) 6285455 Postbus 48
fax: +31 (035) 6838242 3755 ZG Eemnes
http://www.easyhosting.nl
http://www.easycolocate.nl
_______________________________________________
foundry-nsp mailing list
[email protected]
http://puck.nether.net/mailman/listinfo/foundry-nsp
