My guess is you standby system will take B2S and B3L software but not B2R as well? If that's the case then your standby system doesn't have the -PREM upgrade chip.
Jared On Aug 17, 2010, at 12:04 PM, 23media - Tobias Rehn <[email protected]> wrote: > Running System: > > s...@cs1#sh version > SW: Version 08.0.01nT53 Copyright (c) 1996-2004 Foundry Networks, Inc. > Compiled on Sep 13 2007 at 11:38:29 labeled as B2P08001n > (4140183 bytes) from Primary B2P08001n.bin > HW: FastIron 800 Router, SYSIF version 21, Serial #: Non-exist > ========================================================================== > SL 1: J-FIxGMR4 JetCore Management Module, SYSIF 2 (Mini GBIC), ACTIVE > Serial #: CH25023756 > 4096 KB BRAM, JetCore ASIC IGC version 47, BIA version 89 > 32768 KB PRAM and 1M-Bit*1 CAM for IGC 0, version 0447 > 32768 KB PRAM and 1M-Bit*1 CAM for IGC 1, version 0447 > ========================================================================== > SL 2: J-FIxGMR4 JetCore Management Module, SYSIF 2 (Mini GBIC), STANDBY > Serial #: CH29029529 > 4096 KB BRAM, JetCore ASIC IGC version 47, BIA version 89 > 32768 KB PRAM and 1M-Bit*1 CAM for IGC 4, version 0447 > 32768 KB PRAM and 1M-Bit*1 CAM for IGC 5, version 0447 > ========================================================================== > SL 7: J-FI48E-A JetCore Copper E Module, SYSIF 2 > Serial #: CH35040200 > 2048 KB BRAM, JetCore ASIC IPC version 48, BIA version 8a > 8192 KB PRAM and 1M-Bit*1 CAM for IPC 24, version 1848 > 8192 KB PRAM and 1M-Bit*1 CAM for IPC 25, version 1848 > ========================================================================== > Active management module: > 466 MHz Power PC processor 750 (version 8/8302) 66 MHz bus > 512 KB boot flash memory > 16384 KB code flash memory > 256 KB SRAM > 256 MB DRAM > Standby management module: > 466 MHz Power PC processor 750 (version 8/8302) 66 MHz bus > 512 KB boot flash memory > 16384 KB code flash memory > 256 KB SRAM > 256 MB DRAM > The system uptime is 72 days 15 hours 3 minutes 15 seconds > The system started at 04:42:32 GMT+01 Sun Jun 06 2010 > > s...@cs1#sh flash > Active management module: > Code Flash Type: AMD 29LV033C, Size: 64 * 65536 = 4194304, Unit: 4 > Boot Flash Type: AMD 29LV040B, Size: 8 * 65536 = 524288 > Compressed Pri Code size = 4140183, Version 08.0.01nT53 (B2P08001n.bin) > Compressed Sec Code size = 4149861, Version 08.0.01wT53 (B2P08001w.bin) > Maximum Code Image Size Supported: 6815232 (0x0067fe00) > Boot Image size = 281376, Version 07.06.05 (m2b07605.bin) > Used Configuration Flash Size=4593, Max Configuration Flash Size=524288. > > Standby management module: > Code Flash Type: AMD 29LV033C, Size: 64 * 65536 = 4194304, Unit: 4 > Boot Flash Type: AMD 29LV040B, Size: 8 * 65536 = 524288 > Compressed Pri Code size = 4140183, Version 08.0.01nT53 (B2P08001n.bin) > Compressed Sec Code size = 4149861, Version 08.0.01wT53 (B2P08001w.bin) > Maximum Code Image Size Supported: 6815232 (0x0067fe00) > Boot Image Version 07.06.05 (m2b07605.bin) > > > Spare System: > > tel...@brb#sh version > SW: Version 08.0.01uT51 Copyright (c) 1996-2004 Foundry Networks, Inc. > Compiled on Oct 20 2009 at 11:49:39 labeled as B2S08001u > (2794156 bytes) from Primary B2S08001u.bin > HW: FastIron 800 Backbone, SYSIF version 21, Serial #: Non-exist > ========================================================================== > SL 1: J-FIxGMR4 JetCore Management Module, SYSIF 2 (Mini GBIC), ACTIVE > Serial #: CH31032486 > 4096 KB BRAM, JetCore ASIC IGC version 49, BIA version 89 > 32768 KB PRAM and 1M-Bit*1 CAM for IGC 0, version 0449 > 32768 KB PRAM and 1M-Bit*1 CAM for IGC 1, version 0449 > ========================================================================== > SL 5: J-FIxGMR4 JetCore Management Module, SYSIF 2 (Mini GBIC), STANDBY > Serial #: CH31031442 > 4096 KB BRAM, JetCore ASIC IGC version 49, BIA version 89 > 32768 KB PRAM and 1M-Bit*1 CAM for IGC 16, version 0449 > 32768 KB PRAM and 1M-Bit*1 CAM for IGC 17, version 0449 > ========================================================================== > Active management module: > 466 MHz Power PC processor 750 (version 8/8302) 66 MHz bus > 512 KB boot flash memory > 16384 KB code flash memory > 256 KB SRAM > 256 MB DRAM > Standby management module: > 466 MHz Power PC processor 750 (version 8/8302) 66 MHz bus > 512 KB boot flash memory > 16384 KB code flash memory > 256 KB SRAM > 256 MB DRAM > The system uptime is 19 minutes 38 seconds > > tel...@brb#sh flash > Active management module: > Code Flash Type: AMD 29LV033C, Size: 64 * 65536 = 4194304, Unit: 4 > Boot Flash Type: AMD 29LV040B, Size: 8 * 65536 = 524288 > Compressed Pri Code size = 2794156, Version 08.0.01uT51 (B2S08001u.bin) > Compressed Sec Code size = 2794156, Version 08.0.01uT51 (B2S08001u.bin) > Maximum Code Image Size Supported: 6815232 (0x0067fe00) > Boot Image size = 281376, Version 07.06.05 (M2B07605.bin) > Used Configuration Flash Size=448, Max Configuration Flash Size=524288. > > Standby management module: > Code Flash Type: AMD 29LV033C, Size: 64 * 65536 = 4194304, Unit: 4 > Boot Flash Type: AMD 29LV040B, Size: 8 * 65536 = 524288 > Compressed Pri Code size = 2794156, Version 08.0.01uT51 (B2S08001u.bin) > Compressed Sec Code size = 2794156, Version 08.0.01uT51 (B2S08001u.bin) > Maximum Code Image Size Supported: 6815232 (0x0067fe00) > Boot Image Version 07.06.05 (M2B07605.bin) > > > Regards, > Tobi > > > Am 17.08.2010 19:55, schrieb Jared Valentine: >> Maybe the backup system doesn't have the -PREM chips loaded, limiting this >> unit to B2S and B3L software revisions? What code is currently running? >> Can you send a "show flash" and "show version"? >> >> -----Original Message----- >> From: 23media - Tobias Rehn [mailto:[email protected]] >> Sent: Tuesday, August 17, 2010 11:50 AM >> To: Jared Valentine >> Cc: [email protected] >> Subject: Re: [f-nsp] Firmware issue >> >> I tried the same upgrade on another system with the same specs. The >> updates went like a charm. If i try to update my spare system with the >> same hardware (chassis, management, etc) it fails with the following >> error message: >> >> The code type 5 and the subtype 3 are not for this HW, abort! >> File Type check failed. >> TFTP to Flash Error - code 8. >> >> >> Its the same hardware... oO >> >> >> Regards, >> Tobi >> >> >> Am 17.08.2010 19:45, schrieb Jared Valentine: >>> If I remember correctly, B2P was only for NetIron and BigIron management >>> modules . J-FIxGMR4 is "FastIron", and in the 8.0 release notes the only >>> valid images for FastIron were B2R, B2S, or BL3 variants. >>> >>> -Jared >>> >>> >>> >>> -----Original Message----- >>> From: [email protected] >>> [mailto:[email protected]] On Behalf Of 23media - Tobias >>> Rehn >>> Sent: Tuesday, August 17, 2010 11:15 AM >>> To: [email protected] >>> Subject: [f-nsp] Firmware issue >>> >>> >>> >>> Hello, >>> >>> I have a BigIron 8000 chassis with two j-FIxGMR4 management modules. I >>> wanted to install the latest B2P firmware (B2P08001w.bin) but the system >>> does not accept the firmware. It says, that this firmware is not for this >>> system!? According to my research this firmware image should fit. Has >> anyone >>> had such a problem? >>> >>> Regards, >>> Tobi >>> >>> _______________________________________________ >>> foundry-nsp mailing list >>> [email protected] >>> http://puck.nether.net/mailman/listinfo/foundry-nsp >>> >> > > > -- > > 23Media GmbH > Vennheideweg 61f > 48165 Münster > Germany > > Tel +49 251 9879 316 > Mob +49 176 2478 6951 > Fax +49 251 3 9999 900 > > Geschäftsführer/CEO: > Stefan Rehn > Tobias Rehn > > Amtsgericht Münster, HRB 12399 > USt.-ID-Nr.: DE815136232 > > Vertraulichkeit: > Diese E-Mail und ihre Anlagen enthalten vertrauliche bzw. urheberrechtlich > oder durch andere Rechte geschützte Informationen, die nicht öffentlich sind. > Die Übermittlung ist nur an die adressierten Empfänger beabsichtigt. Wenn Sie > nicht zu den beabsichtigten Empfängern gehören, löschen Sie diese E-Mail > inklusive aller Anlagen. Informieren Sie uns bitte per E-Mail oder Telefon > über die fehlgeleitete Zustellung. Unbeabsichtigte Empfänger dieser Mail > dürfen die Inhalte und Anlagen weder kopieren noch offen legen. Die nicht > autorisierte Verwendung, Verbreitung, Verteilung und Wiedergabe dieser E-Mail > oder ihrer Anlagen ist nicht gestattet. > > Confidentiality: > This message and any attachment are confidential and may be privileged or > otherwise protected from disclosure. If you are not the intended recipient, > please return the email to the sender and delete this message and any > attachment from your system. If you are not the intended recipient you must > not copy this message or attachment or disclose the contents to any other > person. Email messages may be monitored and/or recorded by Green Data > Systems. Thank you for your co-operation. > _______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp
