It must be one of those things that "works on a VE" but "not on a physical interface". My example config came from a FESX running 7.x.
-Jared -----Original Message----- From: Jorik Jonker [mailto:[email protected]] Sent: Tuesday, November 02, 2010 10:12 AM To: 'Jared Valentine'; 'Joseph Hardeman'; [email protected] Subject: RE: [f-nsp] VRRP ip-address question Hi, On a CER2024/5.0.00 or a FESX running whatever firmware this is not allowed: (config-if-e1000-1/10-vrid-1)#ip-address 10.0.0.2 (config-if-e1000-1/10-vrid-1)#ip-address 10.0.1.2 error - cannot configure more than 1 ip-addresses per vrid We work around this by having one IP per VRID. Best regards, Jorik Jonker Special Projects, Netherlands [email protected] +31 53 434 0570 TEL +31 53 436 3098 FAX KvK: 06092246 EQUINIX -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Jared Valentine Sent: donderdag 28 oktober 2010 17:29 To: 'Joseph Hardeman'; [email protected] Subject: Re: [f-nsp] VRRP ip-address question I tried it on a Foundry switch and it seems to take it. The config looks like this: router vrrp interface ve 1 ip address 192.168.1.1 255.255.255.0 ip address 192.168.2.1 255.255.255.0 ip vrrp vrid 1 owner ip-address 192.168.1.1 ip-address 192.168.2.1 activate FCX648SHPOE Router(config)#show ip vrrp Total number of VRRP routers defined: 1 Interface ethernet v1 auth-type no authentication VRID 1 state initialize administrative-status enabled mode owner priority 255 current priority 255 hello-interval 1000 msec ip-address 192.168.1.1 192.168.2.1 virtual mac address 0000.5e00.0101 advertise backup: disabled -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Joseph Hardeman Sent: Thursday, October 28, 2010 6:26 AM To: [email protected] Subject: Re: [f-nsp] VRRP ip-address question Hi Everyone, I just looked at what I put down in the example and realized it was totally wrong. Should be: interface ve 100 ip address 192.168.1.1 255.255.255.224 ip address 192.168.2.1 255.255.255.254 ip vrrp vrid 100 ip-address 192.168.1.1 ip-address 192.168.2.1 Anyone have any thoughts on this? Joe On 10/27/2010 8:42 PM, Joseph Hardeman wrote: > Hi Everyone, > > This may be a silly question, but I was doing some thinking and wanted > to know if it was possible. > > If I have a VLAN with multiple subnets on it, for example > 192.168.1.1/27 and 192.168.2.1/28, can the vrrp that handles that > virtual router interface handle multiple ip-address(es) in a single > "ip vrrp vrid" section or would there need to be multiple "ip vrrp > vrid" sections on the interface? > > For example: > > interface ve 100 > ip address 192.168.1.1 255.255.224.0 > ip address 192.168.2.1 255.255.254.0 > ip vrrp vrid 100 > ip-address 192.168.1.1 > ip-address 192.168.2.1 > > I am just curious if this would work. I haven't tried it, but I would > think it would. > > I hope I asked that right. :-) > > Thanks > > Joe _______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp _______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp This email is from Equinix Europe Limited or one of its associated/subsidiary companies. This email, and any files transmitted with it, contains information which is confidential, may be legally privileged and is solely for the use of the intended recipient. If you have received this email in error, please notify the sender and delete this email immediately. Equinix Europe Limited. Registered Office: Quadrant House, 4 Thomas More Square, London E1W 1YW. Registered in England and Wales, No. 6293383. _______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp
