On Fri, Jan 7, 2011 at 4:27 PM, Joseph Hardeman <[email protected]> wrote: > Hi Everyone, > > I am having a bit of an issue, I have gotten a pair of Cisco 6509's with the > SUP-720 engines. I am trying to configure link aggregation between one of > these to a BI4000 I have to test with before we put them into production and > connect them to our BI8000's and fight this problem then. I have been > searching and looking at the docs I have. The configuration I have on the > Cisco's allow them to talk over the port channels between each other with no > issues. > > I can setup the command "link-aggregation active" on port "ethe 1/5" with no > issues it takes the command, but when I go to add a test VLAN on to that > port I get the following error message: > > error - some ports are running LACP and can not be tagged ports. > > Here is the command I am running on the BI: > > test(config)#int e 1/5 > test(config-if-e1000-1/5)#link-aggregate configure key 10000 > test(config-if-e1000-1/5)#link-aggregate active > test(config-if-e1000-1/5)#exit > test(config)#vlan 14 > test(config-vlan-14)#tagged e 1/5 > error - some ports are running LACP and can not be tagged ports. > test(config-vlan-14)#end > > Here is the output of sh int e 1/5" > GigabitEthernet1/5 is up, line protocol is up > Hardware is GigabitEthernet, address is 00e0.52cc.3b04 (bia 00e0.52cc.3b04) > Configured speed 1Gbit, actual 1Gbit, configured duplex fdx, actual fdx > Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING > STP configured to ON, priority is level0, flow control disabled > mirror disabled, monitor disabled > Not member of any active trunks > Not member of any configured trunks > No port name > MTU 1518 bytes, encapsulation ethernet > 300 second input rate: 40104 bits/sec, 72 packets/sec, 0.00% utilization > 300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization > 899789 packets input, 62419802 bytes, 0 no buffer > Received 372 broadcasts, 899417 multicasts, 0 unicasts > 0 input errors, 0 CRC, 0 frame, 0 ignored > 0 runts, 0 giants, DMA received 899786 packets > 0 packets output, 0 bytes, 0 underruns > Transmitted 0 broadcasts, 0 multicasts, 0 unicasts > 0 output errors, 0 collisions, DMA transmitted 0 packets > > > Output of sh link-aggregation: > Long timeout: 90, default: 90 > Short timeout: 3, default: 3 > Port [Sys P] [Port P] [ Key ] [Act][Tio][Agg][Syn][Col][Dis][Def][Exp][Ope] > 1/5 1 1 0 Yes S Agg Syn Col Dis Def No Blo > > > So my question is what am I missing here? From everything I found, all I > have to do after setting 1 or more ports into a link-aggregation is to add > the VLAN's as tagged to the ports with the same key. But its not allowing > me to add the tagged vlans. > > Any suggestions? > > Thanks > > Joe > _______________________________________________
I've had similar problems before. My bookmark takes me to: http://www.techsneeze.com/create-vlan-trunk-between-cisco-ios-and-foundry-bigiron Dave _______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp
