On 1/7/2011 7:36 PM, Big Wave Dave wrote:
On Fri, Jan 7, 2011 at 4:27 PM, Joseph Hardeman<[email protected]> wrote:
Hi Everyone,
I am having a bit of an issue, I have gotten a pair of Cisco 6509's with the
SUP-720 engines. I am trying to configure link aggregation between one of
these to a BI4000 I have to test with before we put them into production and
connect them to our BI8000's and fight this problem then. I have been
searching and looking at the docs I have. The configuration I have on the
Cisco's allow them to talk over the port channels between each other with no
issues.
I can setup the command "link-aggregation active" on port "ethe 1/5" with no
issues it takes the command, but when I go to add a test VLAN on to that
port I get the following error message:
error - some ports are running LACP and can not be tagged ports.
Here is the command I am running on the BI:
test(config)#int e 1/5
test(config-if-e1000-1/5)#link-aggregate configure key 10000
test(config-if-e1000-1/5)#link-aggregate active
test(config-if-e1000-1/5)#exit
test(config)#vlan 14
test(config-vlan-14)#tagged e 1/5
error - some ports are running LACP and can not be tagged ports.
test(config-vlan-14)#end
Here is the output of sh int e 1/5"
GigabitEthernet1/5 is up, line protocol is up
Hardware is GigabitEthernet, address is 00e0.52cc.3b04 (bia 00e0.52cc.3b04)
Configured speed 1Gbit, actual 1Gbit, configured duplex fdx, actual fdx
Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING
STP configured to ON, priority is level0, flow control disabled
mirror disabled, monitor disabled
Not member of any active trunks
Not member of any configured trunks
No port name
MTU 1518 bytes, encapsulation ethernet
300 second input rate: 40104 bits/sec, 72 packets/sec, 0.00% utilization
300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
899789 packets input, 62419802 bytes, 0 no buffer
Received 372 broadcasts, 899417 multicasts, 0 unicasts
0 input errors, 0 CRC, 0 frame, 0 ignored
0 runts, 0 giants, DMA received 899786 packets
0 packets output, 0 bytes, 0 underruns
> Transmitted 0 broadcasts, 0 multicasts, 0 unicasts
0 output errors, 0 collisions, DMA transmitted 0 packets
Output of sh link-aggregation:
Long timeout: 90, default: 90
Short timeout: 3, default: 3
Port [Sys P] [Port P] [ Key ] [Act][Tio][Agg][Syn][Col][Dis][Def][Exp][Ope]
1/5 1 1 0 Yes S Agg Syn Col Dis Def No Blo
So my question is what am I missing here? From everything I found, all I
have to do after setting 1 or more ports into a link-aggregation is to add
the VLAN's as tagged to the ports with the same key. But its not allowing
me to add the tagged vlans.
Any suggestions?
Thanks
Joe
_______________________________________________
I've had similar problems before.
My bookmark takes me to:
http://www.techsneeze.com/create-vlan-trunk-between-cisco-ios-and-foundry-bigiron
Dave
Hi Dave
Thanks for the link, but its only showing how to tag a vlan to the port,
which what I am currently doing but with the new ciscos and adding more
fiber between our routers and switches I wanted to be able to do link
aggregation. I am guessing I can't with this system unless I go with
Trunk mode.
Joe
_______________________________________________
foundry-nsp mailing list
[email protected]
http://puck.nether.net/mailman/listinfo/foundry-nsp
