Hi Gerald, There are more BPDU types than just spanning-tree.. :-) You should apply "no fdp enable" and "no spanning-tree" on the physical interface ethe 1/2, as well as "no ip redirect" and "ipv6 nd suppress-ra" on the VE's which are facing that interface. This should be enough to make the MLXe shut up if "route-only" is also enabled on a global level (though it should be ok with an interface-level "route-only" setting too).
Best regards, Martijn Schmidt On 06/24/2016 11:59 PM, Gerald wrote: > Oh, maybe the trick is disabling STP an the port too: > > ! > vlan 666 name dummy-layer3-vlan > untag eth 1/2 > spanning-tree ethernet 1/2 disable > ! > > Am 24.06.2016 um 23:54 schrieb Gerald: >> All right, I've tested this and now the MLX seems to generate VLAN666 >> BPDUs by itself on this port. At least I can see that the "BPDU Config >> tx" counter is still rising. >> >> So I can stop flooding VLAN1 BPDUs from other ports but now we have new >> VLAN666 BPDUs on that port transmitted. >> >> From one hell to the other... which one is better :-/ >> >> >> Gerald >> >> Am 24.06.2016 um 23:35 schrieb Clement Cavadore: >>> Yes thats it ;) >>> >>> Le 24 juin 2016 23:30:02 GMT+02:00, Gerald <[email protected]> a écrit : >>>> Oops, need sleep ;-) >>>> >>>> ! >>>> int eth 1/2 >>>> enable >>>> route-only >>>> ip addres 10.0.0.1/24 >>>> ! >>>> vlan 666 name dummy-layer3-vlan >>>> untag eth 1/2 >>>> ! >>>> >>>> Am 24.06.2016 um 23:27 schrieb Gerald: >>>>> Thx Clement for this advice, did you mean something like this: >>>>> >>>>> ! >>>>> int eth 1/2 >>>>> enable >>>>> route-only >>>>> ip addres 10.0.0.1/14 >>>>> ! >>>>> vlan 666 name dummy-layer3-vlan >>>>> untag eth 2/12 >>>>> ! >>>>> >>>>> >>>>> Gerald >>>>> >>>>> Am 24.06.2016 um 21:59 schrieb Clement Cavadore: >>>>>> You should create some "dummy" vlans on route-only ports, to avoid >>>> that. >>>>>> No problem having untagged vlan on any port with IP/routing >>>> configuration. You even ca do this without any disturbance. >>>>>> Le 24 juin 2016 21:53:08 GMT+02:00, Gerald <[email protected]> a écrit : >>>>>>> The MLX got a reboot some weeks ago, this seems not to help. I'am >>>>>>> afraid >>>>>>> of your (1) note... :-(. >>>>>>> >>>>>>> Gerald >>>>>>> >>>>>>> Am 24.06.2016 um 21:27 schrieb Steven Raymond: >>>>>>>>> On Jun 24, 2016, at 1:19 PM, Gerald <[email protected]> wrote: >>>>>>>>> >>>>>>>>> Is there a way to stop this? I would have my "route-only" ports >>>>>>> Layer2 >>>>>>>>> free and not disturb other Layer2 systems behind. >>>>>>>> Old old notes I found said basically 1) “bpdus are sent even with >>>>>>> route-only”, and 2) "you should reboot after applying route-only". >>>>>>>> Both of which may not helpful to you. >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>> _______________________________________________ >>>>>>> foundry-nsp mailing list >>>>>>> [email protected] >>>>>>> http://puck.nether.net/mailman/listinfo/foundry-nsp > _______________________________________________ > foundry-nsp mailing list > [email protected] > http://puck.nether.net/mailman/listinfo/foundry-nsp _______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp
