Hi Adrian,
ATH_ENABLE_11N was missing from kernel config, now it works perfectly,
sorry for the noise.
Here's the sysct output FYI:
Nov 26 19:10:12 current kernel: no tx bufs (empty list): 0
Nov 26 19:10:12 current kernel: no tx bufs (was busy): 0
Nov 26 19:10:12 current kernel: aggr single packet: 33
Nov 26 19:10:12 current kernel: aggr single packet w/ BAW closed: 0
Nov 26 19:10:12 current kernel: aggr non-baw packet: 94
Nov 26 19:10:12 current kernel: aggr aggregate packet: 12684
Nov 26 19:10:12 current kernel: aggr single packet low hwq: 2439
Nov 26 19:10:12 current kernel: aggr single packet RTS aggr limited: 0
Nov 26 19:10:12 current kernel: aggr sched, no work: 24419
Nov 26 19:10:12 current kernel: 0: 0 1: 0 2:
3453 3: 138
Nov 26 19:10:12 current kernel: 4: 45 5: 39 6:
2721 7: 4245
Nov 26 19:10:12 current kernel: 8: 337 9: 225 10:
110 11: 90
Nov 26 19:10:12 current kernel: 12: 236 13: 54 14:
104 15: 47
Nov 26 19:10:12 current kernel: 16: 57 17: 48 18:
80 19: 73
Nov 26 19:10:12 current kernel: 20: 46 21: 64 22:
65 23: 62
Nov 26 19:10:12 current kernel: 24: 35 25: 69 26:
25 27: 83
Nov 26 19:10:12 current kernel: 28: 62 29: 38 30:
23 31: 4
Nov 26 19:10:12 current kernel: 32: 6 33: 0 34:
0 35: 0
Nov 26 19:10:12 current kernel: 36: 0 37: 0 38:
0 39: 0
Nov 26 19:10:12 current kernel: 40: 0 41: 0 42:
0 43: 0
Nov 26 19:10:12 current kernel: 44: 0 45: 0 46:
0 47: 0
Nov 26 19:10:12 current kernel: 48: 0 49: 0 50:
0 51: 0
Nov 26 19:10:12 current kernel: 52: 0 53: 0 54:
0 55: 0
Nov 26 19:10:12 current kernel: 56: 0 57: 0 58:
0 59: 0
Nov 26 19:10:12 current kernel: 60: 0 61: 0 62:
0 63: 0
Nov 26 19:10:12 current kernel:
Nov 26 19:10:12 current kernel: HW TXQ 0: axq_depth=0, axq_aggr_depth=0,
axq_fifo_depth=0, holdingbf=0
Nov 26 19:10:12 current kernel: HW TXQ 1: axq_depth=0, axq_aggr_depth=2,
axq_fifo_depth=3, holdingbf=0
Nov 26 19:10:12 current kernel: HW TXQ 2: axq_depth=0, axq_aggr_depth=0,
axq_fifo_depth=0, holdingbf=0
Nov 26 19:10:12 current kernel: HW TXQ 3: axq_depth=0, axq_aggr_depth=0,
axq_fifo_depth=0, holdingbf=0
Nov 26 19:10:12 current kernel: HW TXQ 8: axq_depth=0, axq_aggr_depth=0,
axq_fifo_depth=0, holdingbf=0
Nov 26 19:10:12 current kernel: Total TX buffers: 413; Total TX buffers
busy: 0 (413)
Nov 26 19:10:12 current kernel: Total mgmt TX buffers: 32; Total mgmt TX
buffers busy: 0
Nov 26 19:10:12 current kernel: 0: fifolen: 16/16; head=0; tail=0;
m_pending=0, m_holdbf=0
Nov 26 19:10:12 current kernel: 1: fifolen: 128/128; head=71; tail=71;
m_pending=0, m_holdbf=0
Nov 26 19:10:12 current kernel: Total RX buffers in free list: 368
buffers
Regards,
---
José Pérez
El 2015-11-25 01:18, Adrian Chadd escribió:
Hm, what's in your kenrel config file? Is ENABLE_11N or whatever the
ath driver option there?
sysctl dev.ath.0.txagg=1 ; then check dmesg and output me the results.
Thanks!
-a
On 24 November 2015 at 14:50, José Pérez <f...@aoek.com> wrote:
Dear Svatopluk,
tried again with current, and I get (almost) the same:
Nov 23 18:14:47 current kernel: ath0: ath_edma_rxbuf_alloc: nothing on
rxbuf?!
Nov 23 18:14:47 current kernel: ath0: ath_edma_rxfifo_alloc: Q1: alloc
failed: i=0, nbufs=128?
Nov 23 18:14:47 current kernel: ath0: ath_edma_rxbuf_alloc: nothing on
rxbuf?!
Nov 23 18:14:47 current kernel: ath0: ath_edma_rxfifo_alloc: Q1: alloc
failed: i=1, nbufs=128?
Ideas? Can I help?
Thank you.
Regards,
---
José Pérez
El 2015-11-23 13:45, Svatopluk Kraus escribió:
On Mon, Nov 23, 2015 at 1:12 PM, José Pérez <f...@aoek.com> wrote:
Hi,
I am the (happy?) owner of an Atheros AR9565 which used to work just
fine.
I recently updated an old -current, and a flood of these messages
bumped
up:
Nov 13 17:47:16 test kernel: ath0: ath_edma_rxbuf_alloc: nothing on
rxbuf?!
Nov 13 17:47:16 test kernel: ath0: ath_edma_rxfifo_alloc: Q1: alloc
failed:
i=24, nb
ufs=128?
# pciconf -lv | relevant_part
ath0@pci0:1:0:0: class=0x028000 card=0x064211ad
chip=0x0036168c
rev=0x01 hdr=0x00
vendor = 'Qualcomm Atheros'
device = 'QCA9565 / AR9565 Wireless Network Adapter'
class = network
# dmesg | relevant_part
ath0: <Qualcomm Atheros AR9565> mem 0xf0800000-0xf087ffff irq 32 at
device
0.0 on pci1
ath0: WB335 2-ANT card detected
ar9300_attach: calling ar9300_hw_attach
ar9300_hw_attach: calling ar9300_eeprom_attach
ar9300_flash_map: unimplemented for now
Restoring Cal data from DRAM
Restoring Cal data from EEPROM
Restoring Cal data from Flash
Restoring Cal data from Flash
Restoring Cal data from OTP
ar9300_hw_attach: ar9300_eeprom_attach returned 0
ath0: [HT] enabling HT modes
ath0: [HT] enabling short-GI in 20MHz mode
ath0: [HT] 1 stream STBC receive enabled
ath0: [HT] 1 RX streams; 1 TX streams
ath0: AR9565 mac 704.1 RF5110 phy 2261.3
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0000
# ifconfig | relevant_part
wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0
mtu
1500
ether a4:db:30:ab:ad:ca
inet 192.168.1.2 netmask 0xffffff00 broadcast 192.168.1.255
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: IEEE 802.11 Wireless Ethernet MCS mode 11ng
status: associated
ssid myssid channel 6 (2437 MHz 11g ht/20) bssid
de:ad:be:ee:ee:ef
regdomain ETSI2 country ES indoor ecm authmode WPA2/802.11i
privacy ON deftxkey UNDEF AES-CCM 2:128-bit AES-CCM
3:128-bit
txpower 30 bmiss 7 scanvalid 60 protmode CTS ampdulimit 64k
ampdudensity 4 shortgi wme burst roaming MANUAL
groups: wlan
Is there anything I can help with to improve this? Thank you.
What revision do you use? If you use <r291142, r291192>, please, try
to update to r291193 or higher.
Svatopluk Kraus
Regards,
--
José Pérez
_______________________________________________
freebsd-current@freebsd.org mailing list
https://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to
"freebsd-current-unsubscr...@freebsd.org"
_______________________________________________
freebsd-current@freebsd.org mailing list
https://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to
"freebsd-current-unsubscr...@freebsd.org"
_______________________________________________
freebsd-current@freebsd.org mailing list
https://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to
"freebsd-current-unsubscr...@freebsd.org"
_______________________________________________
freebsd-current@freebsd.org mailing list
https://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscr...@freebsd.org"