On a current from last Sunday I recompiled
a new kernel with just makeoptions DEBUG=-g
and options DDB added to  GENERIC and when
I boot I see the first few spins of the loader
booting the kernel and then all video output stops.
After the boot finishs I get a login prompt but no
keyboard response or video after that.

I am able to ssh into the box, and all seems well
from the "inside". If I recompile GENERIC it works
just fine.

Here is a dmesg, I noticed a few things but nothing I know
how to fix..


Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #2: Sun Jan 28 23:17:40 MST 2001
    [EMAIL PROTECTED]:/usr/src/sys/compile/DEBUG
Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (367.50-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x660  Stepping = 0
real memory  = 134152192 (131008K bytes)
avail memory = 125595648 (122652K bytes)
Preloaded elf kernel "kernel" at 0xc04e7000.
Pentium Pro MTRR support enabled
WARNING: Driver mistake: destroy_dev on 154/0
Using $PIR table, 6 entries at 0xc00fded0
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xe000-0xe01f at device 7.2 on 
pci_cfgintr_virgin: using routable PCI-only interrupt 11
pci_cfgintr: 0:7 INTD routed to irq 11
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, PCI-unknown> at 7.3 (no driver attached)
xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0xe400-0xe47f mem 0xe5000000-0xe500007f 
irq 11 at device 9.0 on pci0
xl0: Ethernet address: 00:10:4b:6e:0a:87
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x0>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sio0: <16550A-compatible COM port> at port 0x3f8-0x407 irq 4 on isa0
sio0: type 16550A
fdc0: <NEC 72065B or clone> at port 0x3f2-0x3f5,0x3f7 irq 6 drq 2 on isa0
ppc0: <Standard parallel printer port> at port 0x378-0x387 irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio1: <16550A-compatible COM port> at port 0x2f8-0x307 irq 3 on isa0
sio1: type 16550A
sbc0: <Creative SB AWE64> at port 0x220-0x22f,0x331-0x332,0x388-0x38b irq 5 drq 1,5 on 
pcm0: <SB16 DSP 4.16> on sbc0
xl0 XXX: driver didn't initialize queue mtx
lp0 XXX: driver didn't initialize queue mtx
gif0 XXX: driver didn't initialize queue mtx
gif1 XXX: driver didn't initialize queue mtx
gif2 XXX: driver didn't initialize queue mtx
gif3 XXX: driver didn't initialize queue mtx
lo0 XXX: driver didn't initialize queue mtx
ppp0 XXX: driver didn't initialize queue mtx
faith0 XXX: driver didn't initialize queue mtx
ad0: 6187MB <FUJITSU MPB3064ATU E> [13410/15/63] at ata0-master UDMA33
Mounting root from ufs:/dev/ad0s4a

To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message

Reply via email to