John Baldwin wrote:
> On 04-Mar-01 Tom Uffner wrote:
> > all of the snapshots since the 24th have exhibited this same or
> > very similar behavior.
> Does it happen for snapshots before the 24th?
no, it does not, at least not for the 5.0-20010210-CURRENT snap.
it boots from the floppies and once installed, from the disk. 

oh well, so much for the idea that it would be easier to get past 
the libc change by installing a snapshot...

Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.0-20010210-CURRENT #0: Sat Feb 10 16:04:54 GMT 2001
    [EMAIL PROTECTED]:/usr/src/sys/compile/GENERIC
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 496311413 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (496.31-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x681  Stepping = 1
real memory  = 134152192 (131008K bytes)
avail memory = 125415424 (122476K bytes)
Preloaded elf kernel "kernel" at 0xc0506000.
Pentium Pro MTRR support enabled
WARNING: Driver mistake: destroy_dev on 154/0
Using $PIR table, 8 entries at 0xc00fdf40
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> at pcibus 0 on
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xfc90-0xfc9f at device 7.1 on
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xfca0-0xfcbf irq 9
at dev
ice 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, PCI-unknown> at 7.3 (no driver attached)
pci0: <serial bus, FireWire> at 8.0 (no driver attached)
pcm0: <Yamaha DS-1E (YMF744)> port 0xfc8c-0xfc8f,0xfcc0-0xfcff mem
fedfffff irq 9 at device 9.0 on pci0
pci0: <simple comms> at 10.0 (no driver attached)
pcic-pci0: <Ricoh RL5C478 PCI-CardBus Bridge> at device 12.0 on pci0
pcic-pci1: <Ricoh RL5C478 PCI-CardBus Bridge> at device 12.1 on pci0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
pcic0: <Intel i82365> at port 0x3e0 iomem 0xd0000 on isa0
pcic0: Polling mode
pccard0: <PC Card bus -- kludge version> on pcic0
pccard1: <PC Card bus -- kludge version> on pcic0
pmtimer0 on isa0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sn0: ioaddr is 0x300
sn0: test1 failed
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: <PNP0303> can't assign resources
unknown: <PNP0e03> can't assign resources
unknown: <PNP0700> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0401> can't assign resources
pccard: card inserted, slot 0
ata1-slave: ata_command: timeout waiting for intr
ata1-slave: identify failed
ad0: 17301MB <IBM-DARA-218000> [35152/16/63] at ata0-master UDMA33
acd0: DVD-ROM <TOSHIBA DVD-ROM SD-C2202> at ata1-master using PIO4
Mounting root from ufs:/dev/ad0s2a
WARNING: / was not properly dismounted
lp0: IPv6 not supported
ed1 at port 0x300-0x31f irq 3 slot 0 on pccard0
ed1: address 00:e0:98:70:10:ee, type Linksys (16 bit)

To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message

Reply via email to