K6-2-450, bus running at 95mhz, Acer 1541 (A? B?)

All works fine with the new ACPI _except_ the clock; the time of day
advances about twice as fast as it should, and I get LOTS of
calcru negative time and time went backwards messages.

NTP is not capable of correcting this gross rate error :-(

My athlon MB (ASUS A7V) still won't boot with the new ACPI, at all.
Dies with a panic trying to attach something, saying can't allocate memory.
The message disappears too fast to remember what it objected to; I think
it was the fxp card.

-- Pete
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #0: Sun Sep  2 21:09:13 PDT 2001
    [EMAIL PROTECTED]:/usr/src/sys/i386/compile/PUFFIN
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 428806046 Hz
CPU: AMD-K6(tm) 3D processor (428.81-MHz 586-class CPU)
  Origin = "AuthenticAMD"  Id = 0x58c  Stepping = 12
  AMD Features=0x80000800<SYSCALL,3DNow!>
real memory  = 201261056 (196544K bytes)
avail memory = 190390272 (185928K bytes)
Preloaded elf kernel "kernel" at 0xc04e6000.
Preloaded elf module "bktr_mem.ko" at 0xc04e609c.
Preloaded elf module "acpi.ko" at 0xc04e613c.
bktr_mem: memory holder loaded
K6-family MTRR support enabled (2 registers)
Using $PIR table, 7 entries at 0xc00fdc20
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <AWARD  AWRDACPI> on motherboard
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI"  frequency 3579545 Hz
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_pcib0: <Host-PCI bridge> port 0x4d6,0x40b,0x480-0x48f,0x5000-0x501f,0x4000-
0x403f,0xcf8-0xcff on acpi0
pci0: <PCI bus> on acpi_pcib0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at 0.0 (no driver attached)
ohci0: <AcerLabs M5237 (Aladdin-V) USB controller> mem 0xe9000000-0xe9000fff irq
 11 at device 2.0 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <AcerLabs M5237 (Aladdin-V) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: AcerLabs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AcerLabs Aladdin ATA33 controller> port 0xf000-0xf00f at device 15.0 o
n pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
bktr0: <BrookTree 848A> mem 0xe9001000-0xe9001fff irq 5 at device 16.0 on pci0
bti2c0: <bt848 Hard/Soft I2C controller>
iicbb0: <I2C generic bit-banging driver> on bti2c0
iicbus0: <Philips I2C bus> on iicbb0 master-only
smbus0: <System Management Bus> on bti2c0
smb0: <SMBus general purpose I/O> on smbus0
bktr0: Pinnacle/Miro TV, Temic NTSC tuner.
rl0: <RealTek 8139 10/100BaseTX> port 0xe000-0xe0ff mem 0xe9002000-0xe90020ff ir
q 10 at device 20.0 on pci0
rl0: Realtek 8139B detected. Warning, this may be unstable in autoselect mode
rl0: Ethernet address: 00:50:ba:02:0b:3d
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fdc0: <NEC 72065B or clone> port 0x3f7,0x3f2-0x3f5 irq 6 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fd1: <1200-KB 5.25" drive> on fdc0 drive 1
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0 port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ppc1: cannot reserve I/O port range
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
ppc1: cannot reserve I/O port range
orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0
sc0: <System console> on isa0
sc0: VGA <12 virtual consoles, flags=0x200>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fdc1: cannot reserve I/O port range (6 ports)
ppc1: cannot reserve I/O port range
IP packet filtering initialized, divert enabled, rule-based forwarding enabled,
default to accept, unlimited logging
IPv6 packet filtering initialized, default to accept, unlimited logging
IPsec: Initialized Security Association Processing.
ad0: 8010MB <Maxtor 90840D6> [16276/16/63] at ata0-master UDMA33
acd0: CDROM <BCD-48SB CD-ROM> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s1a

To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message

Reply via email to