I have a Celeron 500 box (i810 chipset, 128MB/IDE/SCSI) that hangs every
24 hours or so (usually overnight).  I've never had it hang during the day
or while I was using it.  It's running a kernel/world from 8/28 although
this has been happening ever since I installed -current on this box in

The symptoms are I come back to it and the power light is off although the
fan is still running on the power supply.  Numlock is frozen (light is
on).  Nothing can revive it.  Pressing the power button doesn't do
anything either but I can hold it down for 8 secs and the box powers

All these symptoms indicate to me that it is going into some kind of
suspend mode but I have all of that turned off in the BIOS.  APM is
commented out (not just disabled) in my kernel config.  ACPI is loaded.

Thanks for any help,

Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #9: Wed Aug 28 18:20:38 PDT 2002
Preloaded elf kernel "/boot/kernel/kernel" at 0xc04e7000.
Preloaded elf module "/boot/kernel/agp.ko" at 0xc04e70a8.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc04e7150.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 498487691 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (498.49-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x665  Stepping = 5

real memory  = 133103616 (129984K bytes)
avail memory = 123813888 (120912K bytes)
Pentium Pro MTRR support enabled
Using $PIR table, 7 entries at 0xc00fdf50
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <PTLTD    RSDT  > on motherboard
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-fast"  frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_cpu0: <CPU> on acpi0
pcib1: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib1
agp0: <Intel 82810 (i810 GMCH) SVGA controller> mem
0000-0xfbffffff irq 3 at device 1.0 on pci0
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib2
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x3400-0x343f mem
ffff,0xf4300000-0xf4300fff irq 5 at device 11.0 on pci1
fxp0: Ethernet address 00:d0:b7:21:ff:2d
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: <Intel Pro 10/100B/100+ Ethernet> port 0x3440-0x347f mem
ffff,0xf4301000-0xf4301fff irq 9 at device 13.0 on pci1
fxp1: Ethernet address 00:d0:b7:69:21:74
inphy1: <i82555 10/100 media interface> on miibus1
inphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ahc_pci0: <Adaptec 2940 Ultra2 SCSI adapter> port 0x3000-0x30ff mem
xf4302fff irq 3 at device 14.0 on pci1
aic7890/91: Ultra2 Wide Channel A, SCSI Id=14, 32/253 SCBs
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH0 ATA33 controller> port 0x1800-0x180f at device 31.1
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82801AB (ICH0) USB controller> port 0x1820-0x183f irq 11 at
 31.2 on pci0
usb0: <Intel 82801AB (ICH0) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: failed to get data.
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> port
x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0 port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
orm0: <Option ROMs> at iomem
0000-0xc7fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
Profiling kernel, textsize=2119936 [c0123a20..c0329320]
cputime 103, empty_loop 4, nullfunc_loop_profiled 288, mcount 397,
mexitcount 267
Profiling overheads: mcount: 98+294, 258+134; mexitcount: 98+162, 234+26
Profiling overheads: mcount: 49+147, 129+67; mexitcount: 49+81, 117+13
acpi_cpu: CPU throttling enabled, 8 steps from 100% to 12.5%
ad0: DMA limited to UDMA33, non-ATA66 cable or device
ad0: 8297MB <Maxtor 90841U2> [16858/16/63] at ata0-master UDMA33
acd0: CDROM <SAMSUNG CD-ROM SC-140> at ata1-master PIO4
Waiting 5 seconds for SCSI devices to settle
(targbh0:ahc0:0:-1:-1): Lun now enabled for target mode
Mounting root from ufs:/dev/ad0s1a
WARNING: / was not properly dismounted
WARNING: /usr was not properly dismounted
/usr: mount pending error: blocks 4 files 1

To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message

Reply via email to