Hello,

I've changed motherboard recently (now it is Intel DP965LT) and now I
have my PC slowed down considerably. vmstat -i shows a huge amount of
interrupts on irq17: atapci0:
interrupt                          total       rate
irq1: atkbd0                       12535          4
irq12: psm0                         9410          3
irq17: atapci0                 189627864      61507
irq19: atapci1+                   391391        126
irq20: em0                         29076          9
irq22: pcm0                        20557          6
cpu0: timer                      6133486       1989
cpu1: timer                      6133460       1989
Total                          202357779      65636

Since this problem came, my Xorg stopped seeing my PCIE video card. I
guess these two could be related.
I've tried to boot in safe mode and with ACPI disabled but the problem
persists. I've rebuild the kernel with minimal set of options and
devices, but it did not help. I've disabled all non-vital devices from
BIOS, tried to put my SATA drive in Native and legacy modes, tried
with S.M.A.R.T. disabled, disabled USB, FireWire, NIC, serial and
parallel ports, floppy controller, but nothing helped.
What else should I try?

I've attached my dmesg output (with boot_verbose="YES" in loader.conf,
that's why it is so large)
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-STABLE #0: Sat Mar 24 09:35:30 EET 2007
    [EMAIL PROTECTED]:/usr/obj/usr/src/sys/kpax
WARNING: MPSAFE network stack disabled, expect reduced performance.
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0796000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc07961ec.
Calibrating clock(s) ... i8254 clock: 1190766 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 2802815953 Hz
CPU: Intel(R) Pentium(R) D CPU 2.80GHz (2802.82-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf44  Stepping = 4
  
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x641d<SSE3,RSVD2,MON,DS_CPL,CNTX-ID,CX16,<b14>>
  AMD Features=0x20100000<NX,LM>
  Cores per package: 2
real memory  = 1055580160 (1006 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000008dfff, 577536 bytes (141 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000828000 - 0x000000003cce3fff, 1011597312 bytes (246972 pages)
0x000000003df50000 - 0x000000003edfafff, 15380480 bytes (3755 pages)
0x000000003ee07000 - 0x000000003ee9dfff, 618496 bytes (151 pages)
avail memory = 1027379200 (979 MB)
MP Configuration Table version 1.4 found at 0xc00fe670
Table 'FACP' at 0x3eefc000
Table 'APIC' at 0x3eef6000
MADT: Found table at 0x3eef6000
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 1: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 1 ACPI ID 2: enabled
SMP: Added CPU 1 (AP)
MADT: Found CPU APIC ID 130 ACPI ID 3: disabled
MADT: Found CPU APIC ID 131 ACPI ID 4: disabled
INTR: Adding local APIC 0 as a target
ACPI APIC Table: <INTEL  DP965LT >
INTR: Adding local APIC 1 as a target
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
pnpbios: Found PnP BIOS data at 0xc00fe0e0
pnpbios: Entry = f0000:b07f  Rev = 1.0
pnpbios: OEM ID 8224744e
Other BIOS signatures found:
APIC: CPU 0 has ACPI ID 1
APIC: CPU 1 has ACPI ID 2
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: Changing APIC ID to 2
ioapic0: Routing external 8259A's -> intpin 0
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
lapic0: Routing NMI -> LINT1
lapic1: Routing NMI -> LINT1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
cpu0 BSP:
     ID: 0x00000000   VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000100ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
io: <I/O>
random: <entropy source, Software, Yarrow>
npx0: INT 16 interface
acpi0: <INTEL DP965LT> on motherboard
ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48
acpi0: [MPSAFE]
pci_open(1):    mode 1 addr port (0x0cf8) is 0x8000fa18
pci_open(1a):   mode1res=0x80000000 (0x80000000)
pci_cfgcheck:   device 0 [class=060000] [hdr=00] is there (id=29a08086)
pcibios: No call entry point
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 0 func 0
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xd862f000 pa 0x8d000
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 0 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 0 func 0
ACPI timer: 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pci_link0:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   11   N     0  3 4 5 7 9 10 11 12
  Validation          0   11   N     0  3 4 5 7 9 10 11 12
  After Disable       0  255   N     0  3 4 5 7 9 10 11 12
pci_link1:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   10   N     0  3 4 5 7 9 10 11 12
  Validation          0   10   N     0  3 4 5 7 9 10 11 12
  After Disable       0  255   N     0  3 4 5 7 9 10 11 12
pci_link2:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   11   N     0  3 4 5 7 9 10 11 12
  Validation          0   11   N     0  3 4 5 7 9 10 11 12
  After Disable       0  255   N     0  3 4 5 7 9 10 11 12
pci_link3:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   11   N     0  3 4 5 7 9 10 11 12
  Validation          0   11   N     0  3 4 5 7 9 10 11 12
  After Disable       0  255   N     0  3 4 5 7 9 10 11 12
pci_link4:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    9   N     0  3 4 5 7 9 10 11 12
  Validation          0    9   N     0  3 4 5 7 9 10 11 12
  After Disable       0  255   N     0  3 4 5 7 9 10 11 12
pci_link5:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   10   N     0  3 4 5 7 9 10 11 12
  Validation          0   10   N     0  3 4 5 7 9 10 11 12
  After Disable       0  255   N     0  3 4 5 7 9 10 11 12
pci_link6:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    9   N     0  3 4 5 7 9 10 11 12
  Validation          0    9   N     0  3 4 5 7 9 10 11 12
  After Disable       0  255   N     0  3 4 5 7 9 10 11 12
pci_link7:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   11   N     0  3 4 5 7 9 10 11 12
  Validation          0   11   N     0  3 4 5 7 9 10 11 12
  After Disable       0  255   N     0  3 4 5 7 9 10 11 12
cpu0: <ACPI CPU> on acpi0
cpu0: switching to generic Cx mode
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0x410
cpu1: <ACPI CPU> on acpi0
acpi_throttle1: <ACPI CPU Throttling> on cpu1
acpi_throttle1: failed to attach P_CNT
device_attach: acpi_throttle1 attach returned 6
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x29a0, revid=0x02
        bus=0, slot=0, func=0
        class=06-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0006, statreg=0x0090, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x29a1, revid=0x02
        bus=0, slot=1, func=0
        class=06-04-00, hdrtype=0x01, mfdev=0
        cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x18 (6000 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=255
        powerspec 3  supports D0 D3  current D0
        MSI supports 1 message
found-> vendor=0x8086, dev=0x29a4, revid=0x02
        bus=0, slot=3, func=0
        class=07-80-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0006, statreg=0x0010, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=11
        powerspec 3  supports D0 D3  current D0
        MSI supports 1 message, 64 bit
        map[10]: type 1, range 64, base 50325900, size  4, enabled
pcib0: matched entry for 0.3.INTA
pcib0: slot 3 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x104b, revid=0x02
        bus=0, slot=25, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=9
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message, 64 bit
        map[10]: type 1, range 32, base 50300000, size 17, enabled
        map[14]: type 1, range 32, base 50324000, size 12, enabled
        map[18]: type 4, range 32, base 000030c0, size  5, enabled
pcib0: matched entry for 0.25.INTA
pcib0: slot 25 INTA hardwired to IRQ 20
found-> vendor=0x8086, dev=0x2834, revid=0x02
        bus=0, slot=26, func=0
        class=0c-03-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=11
        map[20]: type 4, range 32, base 000030a0, size  5, enabled
pcib0: matched entry for 0.26.INTA
pcib0: slot 26 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x2835, revid=0x02
        bus=0, slot=26, func=1
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=b, irq=10
        map[20]: type 4, range 32, base 00003080, size  5, enabled
pcib0: matched entry for 0.26.INTB
pcib0: slot 26 INTB hardwired to IRQ 21
found-> vendor=0x8086, dev=0x283a, revid=0x02
        bus=0, slot=26, func=7
        class=0c-03-20, hdrtype=0x00, mfdev=0
        cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=c, irq=11
        powerspec 2  supports D0 D3  current D0
        map[10]: type 1, range 32, base 50325400, size 10, enabled
pcib0: matched entry for 0.26.INTC
pcib0: slot 26 INTC hardwired to IRQ 18
found-> vendor=0x8086, dev=0x284b, revid=0x02
        bus=0, slot=27, func=0
        class=04-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=9
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message, 64 bit
        map[10]: type 1, range 64, base 50320000, size 14, enabled
pcib0: matched entry for 0.27.INTA
pcib0: slot 27 INTA hardwired to IRQ 22
found-> vendor=0x8086, dev=0x283f, revid=0x02
        bus=0, slot=28, func=0
        class=06-04-00, hdrtype=0x01, mfdev=1
        cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=255
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message
found-> vendor=0x8086, dev=0x2841, revid=0x02
        bus=0, slot=28, func=1
        class=06-04-00, hdrtype=0x01, mfdev=1
        cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
        intpin=b, irq=255
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message
found-> vendor=0x8086, dev=0x2843, revid=0x02
        bus=0, slot=28, func=2
        class=06-04-00, hdrtype=0x01, mfdev=1
        cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
        intpin=c, irq=255
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message
found-> vendor=0x8086, dev=0x2845, revid=0x02
        bus=0, slot=28, func=3
        class=06-04-00, hdrtype=0x01, mfdev=1
        cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
        intpin=d, irq=255
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message
found-> vendor=0x8086, dev=0x2847, revid=0x02
        bus=0, slot=28, func=4
        class=06-04-00, hdrtype=0x01, mfdev=1
        cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=255
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message
found-> vendor=0x8086, dev=0x2830, revid=0x02
        bus=0, slot=29, func=0
        class=0c-03-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=11
        map[20]: type 4, range 32, base 00003060, size  5, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 23
found-> vendor=0x8086, dev=0x2831, revid=0x02
        bus=0, slot=29, func=1
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=b, irq=11
        map[20]: type 4, range 32, base 00003040, size  5, enabled
pcib0: matched entry for 0.29.INTB
pcib0: slot 29 INTB hardwired to IRQ 19
found-> vendor=0x8086, dev=0x2832, revid=0x02
        bus=0, slot=29, func=2
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=c, irq=11
        map[20]: type 4, range 32, base 00003020, size  5, enabled
pcib0: matched entry for 0.29.INTC
pcib0: slot 29 INTC hardwired to IRQ 18
found-> vendor=0x8086, dev=0x2836, revid=0x02
        bus=0, slot=29, func=7
        class=0c-03-20, hdrtype=0x00, mfdev=0
        cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=11
        powerspec 2  supports D0 D3  current D0
        map[10]: type 1, range 32, base 50325000, size 10, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 23
found-> vendor=0x8086, dev=0x244e, revid=0xf2
        bus=0, slot=30, func=0
        class=06-04-01, hdrtype=0x01, mfdev=0
        cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2810, revid=0x02
        bus=0, slot=31, func=0
        class=06-01-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2820, revid=0x02
        bus=0, slot=31, func=2
        class=01-01-8f, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=11
        powerspec 3  supports D0 D3  current D0
        map[10]: type 4, range 32, base 00003138, size  3, enabled
        map[14]: type 4, range 32, base 0000314c, size  2, enabled
        map[18]: type 4, range 32, base 00003130, size  3, enabled
        map[1c]: type 4, range 32, base 00003148, size  2, enabled
        map[20]: type 4, range 32, base 00003110, size  4, enabled
        map[24]: type 4, range 32, base 00003100, size  4, enabled
pcib0: matched entry for 0.31.INTA
pcib0: slot 31 INTA hardwired to IRQ 19
found-> vendor=0x8086, dev=0x283e, revid=0x02
        bus=0, slot=31, func=3
        class=0c-05-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=b, irq=10
        map[10]: type 1, range 32, base 50325800, size  8, enabled
        map[20]: type 4, range 32, base 00003000, size  5, enabled
pcib0: matched entry for 0.31.INTB
pcib0: slot 31 INTB hardwired to IRQ 21
found-> vendor=0x8086, dev=0x2825, revid=0x02
        bus=0, slot=31, func=5
        class=01-01-85, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x02b0, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=11
        powerspec 3  supports D0 D3  current D0
        map[10]: type 4, range 32, base 00003128, size  3, enabled
        map[14]: type 4, range 32, base 00003144, size  2, enabled
        map[18]: type 4, range 32, base 00003120, size  3, enabled
        map[1c]: type 4, range 32, base 00003140, size  2, enabled
        map[20]: type 4, range 32, base 000030f0, size  4, enabled
        map[24]: type 4, range 32, base 000030e0, size  4, enabled
pcib0: matched entry for 0.31.INTA
pcib0: slot 31 INTA hardwired to IRQ 19
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0x2000-0x2fff
pcib1:   memory decode     0x50200000-0x502fffff
pcib1:   prefetched decode 0x40000000-0x4fffffff
pcib1: could not get PCI interrupt routing table for \\_SB_.PCI0.PEGP - 
AE_NOT_FOUND
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
found-> vendor=0x1002, dev=0x5b63, revid=0x00
        bus=1, slot=0, func=0
        class=03-00-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=11
        powerspec 2  supports D0 D1 D2 D3  current D0
        MSI supports 1 message, 64 bit
        map[10]: type 3, range 32, base 40000000, size 28, enabled
pcib1: requested memory range 0x40000000-0x4fffffff: good
        map[14]: type 4, range 32, base 00002000, size  8, enabled
pcib1: requested I/O range 0x2000-0x20ff: in range
        map[18]: type 1, range 32, base 50210000, size 16, enabled
pcib1: requested memory range 0x50210000-0x5021ffff: good
pcib0: matched entry for 0.1.INTA
pcib0: slot 1 INTA hardwired to IRQ 16
pcib1: slot 0 INTA is routed to irq 16
found-> vendor=0x1002, dev=0x5b73, revid=0x00
        bus=1, slot=0, func=1
        class=03-80-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type 1, range 32, base 50200000, size 16, enabled
pcib1: requested memory range 0x50200000-0x5020ffff: good
pci1: <display, VGA> at device 0.0 (no driver attached)
pci1: <display> at device 0.1 (no driver attached)
pci0: <simple comms> at device 3.0 (no driver attached)
em0: <Intel(R) PRO/1000 Network Connection Version - 6.2.9> port 0x30c0-0x30df 
mem 0x50300000-0x5031ffff,0x50324000-0x50324fff irq 20 at device 25.0 on pci0
em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0x50300000
em0: Reserved 0x20 bytes for rid 0x18 type 4 at 0x30c0
em0: Reserved 0x1000 bytes for rid 0x14 type 3 at 0x50324000
em0: bpf attached
em0: Ethernet address: 00:19:d1:09:de:de
ioapic0: routing intpin 20 (PCI IRQ 20) to vector 49
em0: [GIANT-LOCKED]
pci0: <serial bus, USB> at device 26.0 (no driver attached)
pci0: <serial bus, USB> at device 26.1 (no driver attached)
pci0: <serial bus, USB> at device 26.7 (no driver attached)
pci0: <multimedia> at device 27.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pcib2:   secondary bus     2
pcib2:   subordinate bus   2
pcib2:   I/O decode        0xf000-0xfff
pcib2:   memory decode     0x50400000-0x504fffff
pcib2:   prefetched decode 0xfff00000-0xfffff
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
pcib3: <ACPI PCI-PCI bridge> at device 28.1 on pci0
pcib3:   secondary bus     3
pcib3:   subordinate bus   3
pcib3:   I/O decode        0x1000-0x1fff
pcib3:   memory decode     0x50100000-0x501fffff
pcib3:   prefetched decode 0xfff00000-0xfffff
pci3: <ACPI PCI bus> on pcib3
pci3: physical bus=3
found-> vendor=0x11ab, dev=0x6101, revid=0xb1
        bus=3, slot=0, func=0
        class=01-01-8f, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=10
        powerspec 2  supports D0 D1 D3  current D0
        MSI supports 1 message
        map[10]: type 4, range 32, base 00001018, size  3, enabled
pcib3: requested I/O range 0x1018-0x101f: in range
        map[14]: type 4, range 32, base 00001024, size  2, enabled
pcib3: requested I/O range 0x1024-0x1027: in range
        map[18]: type 4, range 32, base 00001010, size  3, enabled
pcib3: requested I/O range 0x1010-0x1017: in range
        map[1c]: type 4, range 32, base 00001020, size  2, enabled
pcib3: requested I/O range 0x1020-0x1023: in range
        map[20]: type 4, range 32, base 00001000, size  4, enabled
pcib3: requested I/O range 0x1000-0x100f: in range
        map[24]: type 1, range 32, base 50100000, size  9, enabled
pcib3: requested memory range 0x50100000-0x501001ff: good
pcib3: matched entry for 3.0.INTA
pcib3: slot 0 INTA hardwired to IRQ 17
atapci0: <GENERIC ATA controller> port 
0x1018-0x101f,0x1024-0x1027,0x1010-0x1017,0x1020-0x1023,0x1000-0x100f mem 
0x50100000-0x501001ff irq 17 at device 0.0 on pci3
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1000
ioapic0: routing intpin 17 (PCI IRQ 17) to vector 50
atapci0: [MPSAFE]
ata2: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1018
atapci0: Reserved 0x4 bytes for rid 0x14 type 4 at 0x1024
ata2: reset tp1 mask=03 ostat0=50 ostat1=00
ata2: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata2: stat1=0x00 err=0x00 lsb=0x00 msb=0x00
ata2: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata2: [MPSAFE]
ata3: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x1010
atapci0: Reserved 0x4 bytes for rid 0x1c type 4 at 0x1020
ata3: reset tp1 mask=03 ostat0=7f ostat1=7f
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata3: stat1=0x7f err=0xff lsb=0xff msb=0xff
ata3: reset tp2 stat0=ff stat1=ff devices=0x0
ata3: [MPSAFE]
pcib4: <ACPI PCI-PCI bridge> at device 28.2 on pci0
pcib4:   secondary bus     4
pcib4:   subordinate bus   4
pcib4:   I/O decode        0xf000-0xfff
pcib4:   memory decode     0x50500000-0x505fffff
pcib4:   prefetched decode 0xfff00000-0xfffff
pci4: <ACPI PCI bus> on pcib4
pci4: physical bus=4
pcib5: <ACPI PCI-PCI bridge> at device 28.3 on pci0
pcib5:   secondary bus     5
pcib5:   subordinate bus   5
pcib5:   I/O decode        0xf000-0xfff
pcib5:   memory decode     0x50600000-0x506fffff
pcib5:   prefetched decode 0xfff00000-0xfffff
pci5: <ACPI PCI bus> on pcib5
pci5: physical bus=5
pcib6: <ACPI PCI-PCI bridge> at device 28.4 on pci0
pcib6:   secondary bus     6
pcib6:   subordinate bus   6
pcib6:   I/O decode        0xf000-0xfff
pcib6:   memory decode     0x50700000-0x507fffff
pcib6:   prefetched decode 0xfff00000-0xfffff
pci6: <ACPI PCI bus> on pcib6
pci6: physical bus=6
pci0: <serial bus, USB> at device 29.0 (no driver attached)
pci0: <serial bus, USB> at device 29.1 (no driver attached)
pci0: <serial bus, USB> at device 29.2 (no driver attached)
pci0: <serial bus, USB> at device 29.7 (no driver attached)
pcib7: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib7:   secondary bus     7
pcib7:   subordinate bus   7
pcib7:   I/O decode        0xf000-0xfff
pcib7:   memory decode     0x50000000-0x500fffff
pcib7:   prefetched decode 0xfff00000-0xfffff
pcib7:   Subtractively decoded bridge.
pci7: <ACPI PCI bus> on pcib7
pci7: physical bus=7
found-> vendor=0x104c, dev=0x8023, revid=0x00
        bus=7, slot=3, func=0
        class=0c-00-10, hdrtype=0x00, mfdev=0
        cmdreg=0x0016, statreg=0x0210, cachelnsz=16 (dwords)
        lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
        intpin=a, irq=11
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type 1, range 32, base 50004000, size 11, enabled
pcib7: requested memory range 0x50004000-0x500047ff: good
        map[14]: type 1, range 32, base 50000000, size 14, enabled
pcib7: requested memory range 0x50000000-0x50003fff: good
pcib7: matched entry for 7.3.INTA
pcib7: slot 3 INTA hardwired to IRQ 19
pci7: <serial bus, FireWire> at device 3.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <Intel ICH8 SATA300 controller> port 
0x3138-0x313f,0x314c-0x314f,0x3130-0x3137,0x3148-0x314b,0x3110-0x311f,0x3100-0x310f
 irq 19 at device 31.2 on pci0
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0x3110
ioapic0: routing intpin 19 (PCI IRQ 19) to vector 51
atapci1: [MPSAFE]
ata4: <ATA channel 0> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x3138
atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0x314c
ata4: reset tp1 mask=03 ostat0=50 ostat1=00
ata4: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata4: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata4: [MPSAFE]
ata5: <ATA channel 1> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x3130
atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0x3148
ata5: reset tp1 mask=03 ostat0=7f ostat1=7f
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata5: stat1=0x7f err=0xff lsb=0xff msb=0xff
ata5: reset tp2 stat0=ff stat1=ff devices=0x0
ata5: [MPSAFE]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atapci2: <Intel ICH8 SATA300 controller> port 
0x3128-0x312f,0x3144-0x3147,0x3120-0x3127,0x3140-0x3143,0x30f0-0x30ff,0x30e0-0x30ef
 irq 19 at device 31.5 on pci0
atapci2: Reserved 0x10 bytes for rid 0x20 type 4 at 0x30f0
atapci2: [MPSAFE]
ata6: <ATA channel 0> on atapci2
atapci2: Reserved 0x8 bytes for rid 0x10 type 4 at 0x3128
atapci2: Reserved 0x4 bytes for rid 0x14 type 4 at 0x3144
ata6: reset tp1 mask=03 ostat0=7f ostat1=7f
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata6: stat1=0x7f err=0xff lsb=0xff msb=0xff
ata6: reset tp2 stat0=ff stat1=ff devices=0x0
ata6: [MPSAFE]
ata7: <ATA channel 1> on atapci2
atapci2: Reserved 0x8 bytes for rid 0x18 type 4 at 0x3120
atapci2: Reserved 0x4 bytes for rid 0x1c type 4 at 0x3140
ata7: reset tp1 mask=03 ostat0=7f ostat1=7f
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat0=0x7f err=0xff lsb=0xff msb=0xff
ata7: stat1=0x7f err=0xff lsb=0xff msb=0xff
ata7: reset tp2 stat0=ff stat1=ff devices=0x0
ata7: [MPSAFE]
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to vector 52
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0067
psm0: <PS/2 Mouse> irq 12 on atkbdc0
ioapic0: routing intpin 12 (ISA IRQ 12) to vector 53
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000008, packet size:4
psm0: syncmask:08, syncbits:00
atkbdc: atkbdc0 already exists; skipping it
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 
0xc0000-0xcffff,0xd0000-0xd0fff,0xd1000-0xd1fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: reset tp1 mask=00 ostat0=ff ostat1=ff
ioapic0: routing intpin 14 (ISA IRQ 14) to vector 54
ata0: [MPSAFE]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ioapic0: routing intpin 15 (ISA IRQ 15) to vector 55
ata1: [MPSAFE]
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
ppc0 failed to probe at irq 7 on isa0
sio0 failed to probe at port 0x3f8 irq 4 on isa0
sio1 failed to probe at port 0x2f8 irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
lapic: Divisor 2, Frequency 100100280 hz
Timecounter "TSC" frequency 2802815953 Hz quality -100
Timecounters tick every 1.000 msec
IPsec: Initialized Security Association Processing.
lo0: bpf attached
pflog0: bpf attached
pfsync0: bpf attached
em0: Link is up 100 Mbps Full Duplex
ata4-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad8: 152627MB <Seagate ST3160812AS 3.AAD> at ata4-master SATA150
ad8: 312581808 sectors [310101C/16H/63S] 16 sectors/interrupt 1 depth queue
SMP: AP CPU #1 Launched!
cpu1 AP:
     ID: 0x01000000   VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000
ioapic0: Assigning ISA IRQ 1 to local APIC 0
ioapic0: Assigning ISA IRQ 9 to local APIC 1
ioapic0: Assigning ISA IRQ 12 to local APIC 0
ioapic0: Assigning ISA IRQ 14 to local APIC 1
ioapic0: Assigning ISA IRQ 15 to local APIC 0
ioapic0: Assigning PCI IRQ 17 to local APIC 1
ioapic0: Assigning PCI IRQ 19 to local APIC 0
ioapic0: Assigning PCI IRQ 20 to local APIC 1
GEOM: new disk ad8
Trying to mount root from ufs:/dev/ad8s2a
start_init: trying /sbin/init
WARNING: /usr was not properly dismounted
em0: Link is Down
em0: Link is up 100 Mbps Full Duplex
_______________________________________________
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "[EMAIL PROTECTED]"

Reply via email to