Hello everyone,

I'm running a server with FreeBSD 6.2 installed. Since some time the machine freezes completely, following the replies by the hoster even the keyboard won't react so a hard reset is required. There're no error messages like a Kernel Panic on the screen, just a freeze. Once the machine is up again, there's also nothing in the logs which points to a failure.
A dmesg dump:

Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE-p9 #3: Fri Jan 11 13:35:14 CET 2008
    [EMAIL PROTECTED]:/usr/obj/usr/src/sys/ANGELWINGS
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz (2813.53-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf29  Stepping = 9
real memory  = 1072627712 (1022 MB)
avail memory = 1040654336 (992 MB)
Security auditing service present
BSM auditing present
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <GBT AWRDACPI> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff,0x4000-0x40bf on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82845G (845G GMCH) SVGA controller> mem 0xe0000000-0xe7ffffff,0xe8100000-0xe817ffff irq 16 at device 2.0 on pci0
agp0: detected 892k stolen memory
agp0: aperture size is 128M
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xd800-0xd81f irq 16 at device 29.0 on pci0
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xd000-0xd01f irq 19 at device 29.1 on pci0
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xd400-0xd41f irq 18 at device 29.2 on pci0
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> mem 0xe8180000-0xe81803ff irq 23 at device 29.7 on pci0
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib1
rl0: <RealTek 8139 10/100BaseTX> port 0xc000-0xc0ff mem 0xe8000000-0xe80000ff irq 21 at device 5.0 on pci1
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:0d:61:18:38:3e
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FAST]
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
Timecounter "TSC" frequency 2813534500 Hz quality 800
Timecounters tick every 1.000 msec
ad0: 152627MB <WDC WD1600BB-22GUC0 08.02D08> at ata0-master UDMA100
Trying to mount root from ufs:/dev/ad0s1a
rl0: link state changed to UP
arplookup xxx.xxx.xxx.xxx failed: host is not on local network

The arplookup problem was fixed by setting a static route via:

route add -host xxx.xxx.xxx.xxx -interface rl0

and adding an entry in the ARP table.

vmstat -i

interrupt                          total       rate
irq6: fdc0                             3          0
irq14: ata0                         4391          4
irq21: rl0                         21161         23
cpu0: timer                      1823817       1999
Total                            1849372       2027

The server is running Apache 2.2.x in a Chroot Environment, MySQL in a Master <- -> Master replication Mode and PF as Firewall.

Except the self-compiled Kernel the Base System is still the default one from R9 updated via freebsd-update.
The difference to the GENERIC Kernel is the added PF Support and Auditing.

Any help would be welcome

freebsd-questions@freebsd.org mailing list
To unsubscribe, send any mail to "[EMAIL PROTECTED]"

Reply via email to