---------- Original Message ----------- From: Jeff Gardner <[EMAIL PROTECTED]> To: Alex Teslik <[EMAIL PROTECTED]> Cc: list-freebsd-questions <[EMAIL PROTECTED]> Sent: Sun, 08 Feb 2004 01:00:37 -0500 Subject: Re: struggling with hylafax installation
> Alex Teslik wrote: > > Oy, the second post to questions in the same day :( > > > > So, I bought new modem and got it "working", but only kind of - the modem is > > not echoing commands back to the 'cu' or 'ppp' terminals. It is a USRobotics > > 5610B 56K Pro Modem. It is not winmodem and the system put it on sio2. > > Is this an internal or external modem? Internal dmesg | grep 'sio[0-9]': sio0: configured irq 2 not in bitmap of probed irqs 0x20 sio0: <3COM PCI FaxModem> port 0xe000-0xe007 irq 2 at device 10.0 on pci0 sio0: moving to sio2 sio2: type 16550A sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A > > > > > I made all the devices in /dev eventhough they already existed. > > > > I added a direct line to the modem in /etc/remote like: > > cuaa2:dv=/dev/cuaa2:br#57600:pa=none > > > > I can connect to the modem like: > > cu -l /dev/cuaa2 > > or > > tip cuaa2 > > or > > ppp (then 'term') > > > > I can type commands and see them. I type ATDT1234567 and the modem picks up > > and dials. So I know it hears and understands me. But it never echoes back > > result information. I never see an "OK" or anything from the modem in the > > terminal. > > So you get nothing when you type 'AT' followed by enter with nothing else? Correct. > > > > > The problem is that HylaFAX relies on these echo results to control its > > communication with the modem. It is looking for those "OK"s. Does anyone have > > any ideas on how to get the "OK"s working? I have gone through all of the AT > > commands USR documents and I can't get anything. Is this a problem with 'cu' > > or 'ppp' or 'tip'? The results are obviously going somewhere, but I don't know > > where. > > And this makes me ask my first question. Is this internal or external? > > > > > The AT command set for this modem is documented (USR issues the same document > > for all their modems - this is an online version from another model instead of > > a PDF version that is posted with my specific model, but they are the same) here: > > http://www.usr.com/support/839/83909-ug/six.html > > > > This should turn on all echos (but does not): > > ATQ0 E1 F0 > > These should at least get the result codes you need. Maybe try an at&f1 > which is Load Factory 1, HW FC and see if that gets the OK working. The > only thing I could do to mine to turn of the OK is Q1. Nothing with at&f1 or any of the factory settings. Do you have this modem? Are you willing to share the steps you took to get it working properly? uname -a: FreeBSD xxx.xxx.xxx 4.8-RELEASE FreeBSD 4.8-RELEASE #6: Sat Feb 7 16:57:02 PST 2004 [EMAIL PROTECTED]:/usr/obj/usr/src/sys/DUALP3-4_8_0-RELEASE i386 Thanks, Alex _______________________________________________ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to "[EMAIL PROTECTED]"