Hi, I'm currently running fbsd 4.9 on a Toshiba Satellite 2405-S221. 
The problem I am having is that after I install and configure the wireless 
card, I observe no activity between the card and the cpu. 
I know for certain that my pccard slots are fully functional and that fbsd 
is loading the appropriate drivers, but I am puzzled with the lack of 
To setup the client I used the example from the FBSD handbook, 
minus all the WEP encryption crap: 
ifconfig wi0 ssid <ssid goes here> inet <ip goes here> netmask <blah> 
I choose the IP right off the top of my head, I simply make sure that the IP 
is not being used by any other machines on the network. 
Here is my output from dmesg: 
FreeBSD 4.9-RELEASE #0: Tue Jun 29 09:10:13 EST 2004 
    [EMAIL PROTECTED]:/usr/obj/usr/src/sys/MYKERNEL 
Timecounter "i8254"  frequency 1193182 Hz 
CPU: Intel(R) Pentium(R) 4 Mobile CPU 1.60GHz (1594.84-MHz 686-class CPU) 
  Origin = "GenuineIntel"  Id = 0xf24  Stepping = 4 
real memory  = 268238848 (261952K bytes) 
avail memory = 255270912 (249288K bytes) 
Preloaded elf kernel "kernel" at 0xc0597000. 
Warning: Pentium 4 CPU: PSE disabled 
Pentium Pro MTRR support enabled 
md0: Malloc disk 
Using $PIR table, 8 entries at 0xc00f01a0 
apm0: <APM BIOS> on motherboard 
apm0: found APM BIOS v1.2, connected at v1.2 
npx0: <math processor> on motherboard 
npx0: INT 16 interface 
pcib0: <Intel 82845 Host to PCI bridge> on motherboard 
pci0: <PCI bus> on pcib0 
agp0: <Intel 82845 host to AGP bridge> mem 0xf0000000-0xf7ffffff at device 
0.0 on pci0 
pcib1: <Intel 82845 PCI-PCI (AGP) bridge> at device 1.0 on pci0 
pci1: <PCI bus> on pcib1 
pci1: <S3 model 8c2e graphics accelerator> at 0.0 irq 11 
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0xefe0-0xefff 
irq 11 at device 29.0 on pci0 
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0 
usb0: USB revision 1.0 
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 
uhub0: 2 ports with 2 removable, self powered 
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0xef80-0xef9f 
irq 11 at device 29.1 on pci0 
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1 
usb1: USB revision 1.0 
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 
uhub1: 2 ports with 2 removable, self powered 
pcib2: <PCI to PCI bridge (vendor=8086 device=2448)> at device 30.0 on pci0 
pci2: <PCI bus> on pcib2 
fxp0: <Intel 82801CAM (ICH3) Pro/100 VE Ethernet> port 0xdf40-0xdf7f mem 
0xff9ff000-0xff9fffff irq 11 at device 8.0 on pci2 
fxp0: Ethernet address 00:00:39:c9:38:ad 
inphy0: <i82562ET 10/100 media interface> on miibus0 
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto 
pci_cfgintr_linked: linked (6b) to hard-routed irq 11 
pci_cfgintr: 2:10 INTA routed to irq 11 
pcic0: <TI PCI-1410 PCI-CardBus Bridge> irq 11 at device 10.0 on pci2 
pcic0: PCI Memory allocated: 0x88000000 
pcic0: TI12XX PCI Config Reg: [pwr save][pci only] 
pccard0: <PC Card 16-bit bus (classic)> on pcic0 
pci_cfgintr_linked: linked (60) to hard-routed irq 11 
pci_cfgintr: 2:11 INTA routed to irq 11 
pcic1: <Toshiba ToPIC100 PCI-CardBus Bridge> irq 11 at device 11.0 on pci2 
pcic1: PCI Memory allocated: 0x88001000 
pccard1: <PC Card 16-bit bus (classic)> on pcic1 
pci_cfgintr_linked: linked (61) to hard-routed irq 11 
pci_cfgintr: 2:11 INTB routed to irq 11 
pcic2: <Toshiba ToPIC100 PCI-CardBus Bridge> irq 11 at device 11.1 on pci2 
pcic2: PCI Memory allocated: 0x88002000 
pccard2: <PC Card 16-bit bus (classic)> on pcic2 
pci2: <unknown card> (vendor=0x1179, dev=0x0805) at 13.0 irq 11 
isab0: <PCI to ISA bridge (vendor=8086 device=248c)> at device 31.0 on pci0 
isa0: <ISA bus> on isab0 
atapci0: <Intel ICH3 ATA100 controller> port 
0xcfa0-0xcfaf,0xcfe4-0xcfe7,0xcfe8-0xcfef,0xcff4-0xcff7,0xcff8-0xcfff irq 11 
at device 31.1 on pci0 
ata0: at 0x1f0 irq 14 on atapci0 
ata1: at 0x170 irq 15 on atapci0 
pcm0: <Intel ICH3 (82801CA)> port 0xcdc0-0xcdff,0xce00-0xceff irq 11 at 
device 31.5 on pci0 
pcm0: <Yamaha YMF753 AC97 Codec> 
pci0: <unknown card> (vendor=0x8086, dev=0x2486) at 31.6 irq 11 
orm0: <Option ROMs> at iomem 0xc0000-0xcffff,0xe0000-0xeffff on isa0 
pmtimer0 on isa0 
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 
fdc0: FIFO enabled, 8 bytes threshold 
fd0: <1440-KB 3.5" drive> on fdc0 drive 0 
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 
kbd0 at atkbd0 
psm0: <PS/2 Mouse> irq 12 on atkbdc0 
psm0: model IntelliMouse, device ID 3 
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 
sc0: <System console> at flags 0x100 on isa0 
sc0: VGA <16 virtual consoles, flags=0x300> 
sio0: configured irq 4 not in bitmap of probed irqs 0 
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 
sio0: type 8250 
sio1: configured irq 3 not in bitmap of probed irqs 0 
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode 
ppc0: FIFO with 16/16/15 bytes threshold 
plip0: <PLIP network interface> on ppbus0 
lpt0: <Printer> on ppbus0 
lpt0: Interrupt-driven port 
ppi0: <Parallel I/O> on ppbus0 
ad0: 28615MB <TOSHIBA MK3018GAS> [58140/16/63] at ata0-master UDMA100 
acd0: CD-RW <TOSHIBA DVD-ROM SD-R2212> at ata1-master PIO4 
Mounting root from ufs:/dev/ad0s1a 
pccard: card inserted, slot 0 
pccard: card inserted, slot 2 
pccard: card removed, slot 2 
pccard: card inserted, slot 2 
wi0 at port 0x240-0x27f irq 11 slot 0 on pccard0 
wi0: 802.11 address: 00:02:2d:6b:13:ed 
wi0: using Lucent Embedded WaveLAN/IEEE 
wi0: Lucent Firmware: Station 8.10.01 
Output from ifconfig (wi0 left unconfigured) 
localhost# ifconfig 
        inet6 fe80::200:39ff:fec9:38ad%fxp0 prefixlen 64 scopeid 0x1 
        inet netmask 0xffffff00 broadcast 
        ether 00:00:39:c9:38:ad 
        media: Ethernet autoselect (100baseTX <full-duplex>) 
        status: active 
lp0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500 
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 
        inet6 ::1 prefixlen 128 
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3 
        inet netmask 0xff000000 
ppp0: flags=8010<POINTOPOINT,MULTICAST> mtu 1500 
sl0: flags=c010<POINTOPOINT,LINK2,MULTICAST> mtu 552 
faith0: flags=8002<BROADCAST,MULTICAST> mtu 1500 
        inet6 fe80::202:2dff:fe6b:13ed%wi0 prefixlen 64 scopeid 0x7 
        ether 00:02:2d:6b:13:ed 
        media: IEEE 802.11 Wireless Ethernet autoselect (DS/2Mbps) 
        status: no carrier 
        ssid "" 1:"" 
        stationname "FreeBSD WaveLAN/IEEE node" 
        channel 10 authmode OPEN powersavemode OFF powersavesleep 100 
        wepmode OFF weptxkey 1 
ICQ : 26096369 
AIM : itss0lidstate 
[EMAIL PROTECTED] mailing list
To unsubscribe, send any mail to "[EMAIL PROTECTED]"

Reply via email to