On Fri, Oct 10, 2008 at 11:43:26AM +0300, Georgi Iovchev wrote: > > > -- > Friday, October 10, 2008, 4:20:58 AM: > > > On Mon, Oct 06, 2008 at 06:13:34PM +0300, Georgi Iovchev wrote: > >> Hello list > >> > >> I have a shutdown problem. I have a machine with gigabyte GA-G33M-DS2R > >> motherboard. Integrated network card is Realtek 8111B. > >> I can not wake the computer after I shutdown it from FreeBSD. > >> It is a dualboot system - windows xp and freebsd. If I shutdown the > >> computer from windows - later I can wake it up with magic packet. Even > >> if i shutdown the machine on the boot menu with the power button - than > >> later I can wake on lan. The only situation where I CANNOT wake it is > >> when I shutdown the machine from freebsd (halt -p). > >> > >> First I tested with 7.0-RELEASE-p5 amd64 (RELENG_7_0) and than I > >> upgraded to 7.1 PRERELASE amd64 (RELENG_7). I also tested with two > >> network cards - the integrated one Realtek 8111B and another one Intel > >> PRO1000PT PCI-E with WOL enabled. > >> > > > Don't know WOL issue of em(4) but re(4) should respond to WOL. > > 7.0-RELEASE had no support for WOL so RELENG_7 or 7.1-PRERELEASE > > should be used to experiment WOL. > Now I am using 7.1-prerelase > > >> With both nics and both freebsd versions the situation is the same - > >> after shutdown from bsd the computer is not able to wake on lan. The > > > Because you can wake up your sytem from Windows shutdown I think > > your BIOS is already configured to allow wakeup from WOL. Would > > you compare ethernet address of re(4) to Winwods? Have you tried to > > send Magic packets to FreeBSD box? > I have tried sending magic packets from another bsd machine. I am > using net/wol. I also tried to send magic packets from windows machine > using 3 different programs. > > > You may also try suspend your box with acpiconf and resume from WOL. > I cant. > > [EMAIL PROTECTED] ~]# acpiconf -s 5 > acpiconf: invalid sleep type (5) > > Actually I cant enter in any sleep state > [EMAIL PROTECTED] ~]# acpiconf -s 4 > acpiconf: request sleep type (4) failed: Operation not supported > [EMAIL PROTECTED] ~]# acpiconf -s 3 > acpiconf: request sleep type (3) failed: Operation not supported > [EMAIL PROTECTED] ~]# acpiconf -s 2 > acpiconf: request sleep type (2) failed: Operation not supported > [EMAIL PROTECTED] ~]# acpiconf -s 1 > acpiconf: request sleep type (1) failed: Operation not supported > > I am using generic kernel with little modifications, (generally i have > commented many unused drivers - raid, if_....) Acpi is in generic > kernel now. > > I even tried to wake the machine with magic packet after shutdown -h. > But still no luck. > > > >> indication on the switch port says that after shut down there is > >> active link. > >> > > > That indicates the controller is alive so it shall respond to WOL > > if it was correctly configured to receive WOL packets. Have you > > tried to send Magic packets to FreeBSD box? > > >> Here is some information after last update: > >> > >> [EMAIL PROTECTED] ~]# uname -a > >> FreeBSD backup.pulsar.bg 7.1-PRERELEASE FreeBSD > >> 7.1-PRERELEASE #1: Mon Oct 6 17:01:26 EEST 2008 > >> [EMAIL PROTECTED]:/usr/obj/usr/src/sys/MYCONF amd64 > >> > >> [EMAIL PROTECTED] ~]# pciconf -lv > >> ... > >> [EMAIL PROTECTED]:3:0:0: class=0x020000 card=0xe0001458 > >> chip=0x816810ec rev=0x01 hdr=0x00 > >> vendor = 'Realtek Semiconductor' > >> device = 'RTL8168/8111 PCI-E Gigabit Ethernet NIC' > >> class = network > >> subclass = ethernet > >> ... > > > Show me dmesg output pertinent to re(4). > > re0: <RealTek 8168/8168B/8168C/8168CP/8111B/8111C/8111CP PCIe Gigabit > Ethernet> port 0xd000-0xd0ff mem 0xf2000000-0xf2000fff irq 17 at device 0.0 > on pci3 > re0: turning off MSI enable bit. > re0: Chip rev. 0x38000000 > re0: MAC rev. 0x00000000 > miibus0: <MII bus> on re0 > rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0 > rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, > 1000baseT-FDX, auto > re0: Ethernet address: 00:1f:d0:24:19:e9 > re0: [FILTER] >
It looks like your chip is RTL8168B and I don't see any errors in WOL related code of re(4). :-( Can you check the resolved link speed/duplex of FreeBSD box after shutdown?(You can enter to your switch menu and see the port status.) How about sending WOL packets over direct-connected UTP cable without using switch? -- Regards, Pyun YongHyeon _______________________________________________ [email protected] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "[EMAIL PROTECTED]"
