Pyun YongHyeon wrote:
On Tue, Oct 14, 2008 at 03:44:56PM +0900, To Georgi Iovchev wrote:
> On Fri, Oct 10, 2008 at 11:43:26AM +0300, Georgi Iovchev wrote:
> >
> >
> > --
> > Friday, October 10, 2008, 4:20:58 AM:
> >
> > > On Mon, Oct 06, 2008 at 06:13:34PM +0300, Georgi Iovchev wrote:
> > >> Hello list
> > >>
> > >> I have a shutdown problem. I have a machine with gigabyte GA-G33M-DS2R
> > >> motherboard. Integrated network card is Realtek 8111B.
> > >> I can not wake the computer after I shutdown it from FreeBSD.
> > >> It is a dualboot system - windows xp and freebsd. If I shutdown the
> > >> computer from windows - later I can wake it up with magic packet. Even
> > >> if i shutdown the machine on the boot menu with the power button -
than
> > >> later I can wake on lan. The only situation where I CANNOT wake it is
> > >> when I shutdown the machine from freebsd (halt -p).
> > >>
> > >> First I tested with 7.0-RELEASE-p5 amd64 (RELENG_7_0) and than I
> > >> upgraded to 7.1 PRERELASE amd64 (RELENG_7). I also tested with two
> > >> network cards - the integrated one Realtek 8111B and another one Intel
> > >> PRO1000PT PCI-E with WOL enabled.
> > >>
> >
> > > Don't know WOL issue of em(4) but re(4) should respond to WOL.
> > > 7.0-RELEASE had no support for WOL so RELENG_7 or 7.1-PRERELEASE
> > > should be used to experiment WOL.
> > Now I am using 7.1-prerelase
> >
> > >> With both nics and both freebsd versions the situation is the same -
> > >> after shutdown from bsd the computer is not able to wake on lan. The
> >
> > > Because you can wake up your sytem from Windows shutdown I think
> > > your BIOS is already configured to allow wakeup from WOL. Would
> > > you compare ethernet address of re(4) to Winwods? Have you tried to
> > > send Magic packets to FreeBSD box?
> > I have tried sending magic packets from another bsd machine. I am
> > using net/wol. I also tried to send magic packets from windows machine
> > using 3 different programs.
> >
> > > You may also try suspend your box with acpiconf and resume from WOL.
> > I cant.
> >
> > [EMAIL PROTECTED] ~]# acpiconf -s 5
> > acpiconf: invalid sleep type (5)
> >
> > Actually I cant enter in any sleep state
> > [EMAIL PROTECTED] ~]# acpiconf -s 4
> > acpiconf: request sleep type (4) failed: Operation not supported
> > [EMAIL PROTECTED] ~]# acpiconf -s 3
> > acpiconf: request sleep type (3) failed: Operation not supported
> > [EMAIL PROTECTED] ~]# acpiconf -s 2
> > acpiconf: request sleep type (2) failed: Operation not supported
> > [EMAIL PROTECTED] ~]# acpiconf -s 1
> > acpiconf: request sleep type (1) failed: Operation not supported
> >
> > I am using generic kernel with little modifications, (generally i have
> > commented many unused drivers - raid, if_....) Acpi is in generic
> > kernel now.
> >
> > I even tried to wake the machine with magic packet after shutdown -h.
> > But still no luck.
> >
> >
> > >> indication on the switch port says that after shut down there is
> > >> active link.
> > >>
> >
> > > That indicates the controller is alive so it shall respond to WOL
> > > if it was correctly configured to receive WOL packets. Have you
> > > tried to send Magic packets to FreeBSD box?
> >
> > >> Here is some information after last update:
> > >>
> > >> [EMAIL PROTECTED] ~]# uname -a
> > >> FreeBSD backup.pulsar.bg 7.1-PRERELEASE FreeBSD
> > >> 7.1-PRERELEASE #1: Mon Oct 6 17:01:26 EEST 2008
> > >> [EMAIL PROTECTED]:/usr/obj/usr/src/sys/MYCONF amd64
> > >>
> > >> [EMAIL PROTECTED] ~]# pciconf -lv
> > >> ...
> > >> [EMAIL PROTECTED]:3:0:0: class=0x020000 card=0xe0001458
> > >> chip=0x816810ec rev=0x01 hdr=0x00
> > >> vendor = 'Realtek Semiconductor'
> > >> device = 'RTL8168/8111 PCI-E Gigabit Ethernet NIC'
> > >> class = network
> > >> subclass = ethernet
> > >> ...
> >
> > > Show me dmesg output pertinent to re(4).
> >
> > re0: <RealTek 8168/8168B/8168C/8168CP/8111B/8111C/8111CP PCIe Gigabit Ethernet> port 0xd000-0xd0ff mem 0xf2000000-0xf2000fff irq 17 at device 0.0 on pci3
> > re0: turning off MSI enable bit.
> > re0: Chip rev. 0x38000000
> > re0: MAC rev. 0x00000000
> > miibus0: <MII bus> on re0
> > rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0
> > rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
> > re0: Ethernet address: 00:1f:d0:24:19:e9
> > re0: [FILTER]
> >
>
> It looks like your chip is RTL8168B and I don't see any errors in
> WOL related code of re(4). :-(
> Can you check the resolved link speed/duplex of FreeBSD box after
> shutdown?(You can enter to your switch menu and see the port
> status.)
> How about sending WOL packets over direct-connected UTP cable
> without using switch?
>
Hello again :)
I have resumed my experimets with wol again.
I checked the link speed from the switch web gui. It says "100M Full".
Here is WOL patch which may fix the issye. Would you try the
following patch and let me know whether WOL works or not?
http://people.freebsd.org/~yongari/re/re.phy.patch.20081103
I tried your patch. Just to be sure that I did it correct - here are my
steps:
cd /
patch < /path/re.phy.patch.20081103
cd /sys/modules/re
make all install
reboot
After reboot I shutdown the machine and try to wake it from another
computer.
Still WOL does not work.
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
