On 11/17/2011 19:48, Hans Petter Selasky wrote:
On Thursday 17 November 2011 19:14:35 Jan Henrik Sylvester wrote:
On 11/15/2011 21:40, Hans Petter Selasky wrote:
On Tuesday 15 November 2011 14:14:20 Jan Henrik Sylvester wrote:
On 11/05/2011 13:15, Hans Petter Selasky wrote:
On Friday 04 November 2011 12:33:53 Jan Henrik Sylvester wrote:
On 11/04/2011 10:18, Hans Petter Selasky wrote:
On Thursday 03 November 2011 22:04:44 Xin LI wrote:
Xin LI

Please try the following patch:


Then send me the XHCI attach error.

Probably something which we can fix.

Ok, I have found a minute to test 9.0-RC1 + 227075:

xhci0:<XHCI (generic) USB 3.0 controller>    mem 0xf1f00000-0xf1f0ffff
irq 19 at device 0.0 on pci5
xhci0: 32 byte context size.
xhci0: Controller reset timeout.
xhci0: XHCI halt/start/probe failed err=18
WARNING: A USB process has been left suspended
device_attach: xhci0 attach returned 6

BTW: I think it is this device from "pciconf -l":
xhci0@pci0:5:0:0:       class=0x0c0330 card=0x10001d5c chip=0x10001b73
rev=0x01 hdr=0x00

In sys/dev/usb/controller/xhci.c

Try to increase the usb_pause_mtx() from hz/1000 to hz/100.

If that doesn't work try to continue, even if the HC is not clearing
the HCRST bit. Also print "temp" at the end of the loop.

        /* Reset controller */
        for (i = 0; i != 100; i++) {
                usb_pause_mtx(NULL, hz / 1000);
                temp = XREAD4(sc, oper, XHCI_USBCMD)&
                (XHCI_CMD_HCRST | XHCI_STS_CNR);
                if (!temp)
        if (temp) {
                device_printf(sc->sc_bus.parent, "Controller "
                    "reset timeout.\n");
                return (USB_ERR_IOERROR);

I have put hz/100 in all four places of usb_pause_mtx(), replacing
hz/1000 three times and hz/250 once. temp is never != 0 in that loop now
and the controller attaches:

xhci0:<XHCI (generic) USB 3.0 controller>   mem 0xf1f00000-0xf1f0ffff irq
19 at d
evice 0.0 on pci5
xhci0: 32 byte context size.
usbus1 on xhci0

Anyhow, trying to attach an umass device fails:

xhci_do_command: Command timeout!
xhci_do_command: Command timeout!
xhci_do_command: Command timeout!
ugen1.2:<FUJITSU>   at usbus1
umass0:<FUJITSU MB86C311, class 0/0, rev 3.00/0.01, addr 1>   on usbus1
umass0:  SCSI over Bulk-Only; quirks = 0x0000
xhci_do_command: Command timeout!
xhci_do_command: Command timeout!
umass0: Get Max Lun not supported (USB_ERR_TIMEOUT)
umass0:5:0:-1: Attached to scbus5
xhci_do_command: Command timeout!


And many more "Command timeout!" after that.

Can you compile the kernel with "options USB_DEBUG" in the kernel
configuration file and set hw.usb.xhci.debug=15 during bootup?

I will get those delay changes into the mainline code.

I have done some more testing, now on 9.0-RC2/amd64. Thus, I did not
need the usb_request.c changes from r227075 anymore and used GENERIC
(from freebsd-update) for some tests and GENERIC plus all (three) "hz /
1000" changed to "hz / 100" in xhci.c as in r227541 for the others.

First, I removed kern.hz=100 (together with hint.p4tcc.0.disabled=1,
hint.acpi_throuttle.0.disabled=1, hint.apic.0.clock=0, and
hint.atrtc.0.clock=0) from loader.conf. Later, I put it back in.

9.0-RC2/amd64 GENERIC with standard kern.hz works: I get /dev/da0 from
the harddisk attached that I can use subsequently.

9.0-RC2/amd64 GENERIC with kern.hz=100 produces the xhci timeout, but
with the xhci.c patch, it works, too.

9.0-RC2/amd64 GENERIC with kern.hz=250 without the xhci.c patch does not
work, either.

"umass0: Get Max Lun not supported" and so on never appeared again.
(Maybe due to some other changes between RC1 and RC2? There was r226803
for example and probably more to other related files.)

I did some of the testing with hw.usb.xhci.debug=15 in case you still
want to have a look. Once (with kern.hz=100), the system did not respond
anymore, after I repeatedly had run dmesg to see if/when /dev/da0
appears. Anyhow, I was not able to reproduce that and after I rebooted I
saw the huge debug output on the first console after attaching the

Since I not know if the list takes attachments, some dmesg output are
here for a few days:



Summed up: You got it working when removing some boot/loader.conf options?

Sorry for too many details. No:

I got it working on RC2 with the same setup that failed on RC1.

For kern.hz=100 or kern.hz=250, I need r227541, while default kern.hz works on RC2.

Do you want anything else? Do you want me to go back to 9.0-RC1 and try
to reproduce the error with hw.usb.xhci.debug=15?

Maybe you can set xhci.debug=0 again, and only send dmesg of what happens when
you attach at kern.hz=100 and kern.hz=1000.

I want to see the errors. Not sure yet what actually causes this. I assume
that this is maybe a software or hardware timing issue.

I am not sure what you want: RC1 (with the umass error) without hw.usb.xhci.debug=15 is already way above -- at least the relevant part. For RC2 (without the umass error), the "nodebug" cases linked above are already what you ask for (hz100-patched is kern.hz=100 with r227541, hz250 is kern.hz=250 without r227541, and the other is default kern.hz without r227541).

Jan Henrik
freebsd-usb@freebsd.org mailing list
To unsubscribe, send any mail to "freebsd-usb-unsubscr...@freebsd.org"

Reply via email to