The following reply was made to PR usb/188403; it has been noted by GNATS.

From: Hans Petter Selasky <h...@selasky.org>
To: Jason Seidel <jsei...@unixsystem.org>, 
 freebsd-gnats-sub...@freebsd.org
Cc:  
Subject: Re: usb/188403: USB3 USB_ERR_TIMEOUT and USB_ERR_STALLED issues
Date: Wed, 09 Apr 2014 22:30:15 +0200

 On 04/09/14 17:39, Jason Seidel wrote:
 >
 >> Number:         188403
 >> Category:       usb
 >> Synopsis:       USB3 USB_ERR_TIMEOUT and USB_ERR_STALLED issues
 >> Confidential:   no
 >> Severity:       non-critical
 >> Priority:       low
 >> Responsible:    freebsd-usb
 >> State:          open
 >> Quarter:
 >> Keywords:
 >> Date-Required:
 >> Class:          sw-bug
 >> Submitter-Id:   current-users
 >> Arrival-Date:   Wed Apr 09 15:40:00 UTC 2014
 >> Closed-Date:
 >> Last-Modified:
 >> Originator:     Jason Seidel
 >> Release:        Freebsd 10 release/stable and 11.0-current
 >> Organization:
 >> Environment:
 > I have tried this with all current FreeBSD 10 versions.
 >
 > FreeBSD nuc 11.0-CURRENT FreeBSD 11.0-CURRENT #1 r264292: Wed Apr  9 
 > 10:14:56 EDT 2014     jseidel@nuc:/usr/obj/usr/src/sys/GENERIC  i386
 >
 >> Description:
 > I have an intel NUC D34010WYKH, and there is an issue with the USB3 in 
 > release 10 and 11. I was running freebsd 10 release and saw this issuebut i 
 > needed to upgrade to stable because release didnt contain the axge driver 
 > for a usb network adapter. after updating to stable, the driver was 
 > available but the usb errors were still there. I saw some messages about 
 > issues like this and that a fix was uploaded, so I went to current to see if 
 > it fixed the problem, but the issue was still there.
 >
 > usb_alloc_device: set address 5 failed (USB_ERR_TIMEOUT, ignored)
 > usbd_setup_device_desc: getting device descriptor at addr 5 failed, 
 > USB_ERR_STALLED
 > Root mount waiting for: usbus1
 > usbd_req_re_enumerate: addr=5, set address failed! (USB_ERR_TIMEOUT, ignored)
 > usbd_setup_device_desc: getting device descriptor at addr 5 failed, 
 > USB_ERR_STALLED
 > Root mount waiting for: usbus1
 > Root mount waiting for: usbus1
 > usbd_req_re_enumerate: addr=5, set address failed! (USB_ERR_TIMEOUT, ignored)
 > usbd_setup_device_desc: getting device descriptor at addr 5 failed, 
 > USB_ERR_STALLED
 > Root mount waiting for: usbus1
 > usbd_req_re_enumerate: addr=5, set address failed! (USB_ERR_TIMEOUT, ignored)
 > usbd_setup_device_desc: getting device descriptor at addr 5 failed, 
 > USB_ERR_STALLED
 > Root mount waiting for: usbus1
 > Root mount waiting for: usbus1
 > usbd_req_re_enumerate: addr=5, set address failed! (USB_ERR_TIMEOUT, ignored)
 > usbd_setup_device_desc: getting device descriptor at addr 5 failed, 
 > USB_ERR_STALLED
 >
 >
 > $ pciconf -lv
 > hostb0@pci0:0:0:0:      class=0x060000 card=0x20548086 chip=0x0a048086 
 > rev=0x09 hdr=0x00
 >      vendor     = 'Intel Corporation'
 >      device     = 'Haswell-ULT DRAM Controller'
 >      class      = bridge
 >      subclass   = HOST-PCI
 > vgapci0@pci0:0:2:0:     class=0x030000 card=0x20548086 chip=0x0a268086 
 > rev=0x09 hdr=0x00
 >      vendor     = 'Intel Corporation'
 >      device     = 'Haswell-ULT Integrated Graphics Controller'
 >      class      = display
 >      subclass   = VGA
 > hdac0@pci0:0:3:0:       class=0x040300 card=0x20548086 chip=0x0a0c8086 
 > rev=0x09 hdr=0x00
 >      vendor     = 'Intel Corporation'
 >      class      = multimedia
 >      subclass   = HDA
 > xhci0@pci0:0:20:0:      class=0x0c0330 card=0x20548086 chip=0x9c318086 
 > rev=0x04 hdr=0x00
 >      vendor     = 'Intel Corporation'
 >      device     = 'Lynx Point-LP USB xHCI HC'
 >      class      = serial bus
 >      subclass   = USB
 > none0@pci0:0:22:0:      class=0x078000 card=0x20548086 chip=0x9c3a8086 
 > rev=0x04 hdr=0x00
 >      vendor     = 'Intel Corporation'
 >      device     = 'Lynx Point-LP HECI'
 >      class      = simple comms
 > em0@pci0:0:25:0:        class=0x020000 card=0x20548086 chip=0x15598086 
 > rev=0x04 hdr=0x00
 >      vendor     = 'Intel Corporation'
 >      class      = network
 >      subclass   = ethernet
 > hdac1@pci0:0:27:0:      class=0x040300 card=0x20548086 chip=0x9c208086 
 > rev=0x04 hdr=0x00
 >      vendor     = 'Intel Corporation'
 >      device     = 'Lynx Point-LP HD Audio Controller'
 >      class      = multimedia
 >      subclass   = HDA
 > pcib1@pci0:0:28:0:      class=0x060400 card=0x20548086 chip=0x9c108086 
 > rev=0xe4 hdr=0x01
 >      vendor     = 'Intel Corporation'
 >      device     = 'Lynx Point-LP PCI Express Root Port 1'
 >      class      = bridge
 >      subclass   = PCI-PCI
 > pcib2@pci0:0:28:3:      class=0x060400 card=0x20548086 chip=0x9c168086 
 > rev=0xe4 hdr=0x01
 >      vendor     = 'Intel Corporation'
 >      device     = 'Lynx Point-LP PCI Express Root Port 4'
 >      class      = bridge
 >      subclass   = PCI-PCI
 > ehci0@pci0:0:29:0:      class=0x0c0320 card=0x20548086 chip=0x9c268086 
 > rev=0x04 hdr=0x00
 >      vendor     = 'Intel Corporation'
 >      device     = 'Lynx Point-LP USB EHCI'
 >      class      = serial bus
 >      subclass   = USB
 > isab0@pci0:0:31:0:      class=0x060100 card=0x20548086 chip=0x9c438086 
 > rev=0x04 hdr=0x00
 >      vendor     = 'Intel Corporation'
 >      device     = 'Lynx Point-LP LPC Controller'
 >      class      = bridge
 >      subclass   = PCI-ISA
 > ahci0@pci0:0:31:2:      class=0x010601 card=0x20548086 chip=0x9c038086 
 > rev=0x04 hdr=0x00
 >      vendor     = 'Intel Corporation'
 >      device     = 'Lynx Point-LP SATA Controller 1 [AHCI mode]'
 >      class      = mass storage
 >      subclass   = SATA
 > none1@pci0:0:31:3:      class=0x0c0500 card=0x20548086 chip=0x9c228086 
 > rev=0x04 hdr=0x00
 >      vendor     = 'Intel Corporation'
 >      device     = 'Lynx Point-LP SMBus Controller'
 >      class      = serial bus
 >      subclass   = SMBus
 > none2@pci0:2:0:0:       class=0x028000 card=0x40708086 chip=0x08b18086 
 > rev=0x73 hdr=0x00
 >      vendor     = 'Intel Corporation'
 >      class      = network
 >
 > # usbconfig
 > ugen1.1: <EHCI root HUB Intel> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) 
 > pwr=SAVE (0mA)
 > ugen0.1: <XHCI root HUB 0x8086> at usbus0, cfg=0 md=HOST spd=SUPER (5.0Gbps) 
 > pwr=SAVE (0mA)
 > ugen1.2: <product 0x8000 vendor 0x8087> at usbus1, cfg=0 md=HOST spd=HIGH 
 > (480Mbps) pwr=SAVE (0mA)
 > ugen1.3: <AX88179 ASIX Elec. Corp.> at usbus1, cfg=0 md=HOST spd=HIGH 
 > (480Mbps) pwr=ON (248mA)
 > ugen1.4: <USB Receiver Logitech> at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) 
 > pwr=ON (98mA)
 >
 >
 >> How-To-Repeat:
 > fresh install of freebsd exibits this issue.
 >> Fix:
 > I have gotten it to "somewhat" stabilize by adding 
 > hw.usb.xhci.xhci_port_route=-1 into /boot/loader.conf
 >
 >> Release-Note:
 >> Audit-Trail:
 
 Hi,
 
 Can you try this patch:
 
 http://svnweb.freebsd.org/changeset/base/264294
 
 --HPS
_______________________________________________
freebsd-usb@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-usb
To unsubscribe, send any mail to "freebsd-usb-unsubscr...@freebsd.org"

Reply via email to