On Mon, Dec 22, 2014 at 12:42 AM, Hans Petter Selasky <h...@selasky.org>
wrote:

> On 12/21/14 22:28, Randall Fox wrote:
>
>> On Sun, Dec 21, 2014 at 1:02 PM, Hans Petter Selasky <h...@selasky.org>
>> wrote:
>>
>>  On 12/21/14 21:40, Randall Fox wrote:
>>>
>>>  Did you update /etc/devd/usb.conf, install new kernel and reboot your
>>>>
>>>>>
>>>>>  system?
>>>>
>>>> I actually had the FreeNAS team apply this fix to the nightly build and
>>>> I
>>>> created a whole new install based on their Nightly Build.  The DEVs put
>>>> the
>>>> fix in, and it must have been correct because it worked for someone
>>>> else.
>>>>
>>>> Here is the link to the ticket for this:
>>>> https://bugs.freenas.org/issues/7153
>>>> It appears they are familiar with you!
>>>>
>>>> I will try putting the usb.conf in the location you specify, to see if
>>>> that
>>>> works.  I would be surprised if the dev's missed this.
>>>>
>>>>
>>>>
>>>> On Sun, Dec 21, 2014 at 12:24 PM, Hans Petter Selasky <h...@selasky.org>
>>>> wrote:
>>>>
>>>>   On 12/21/14 21:21, Randall Fox wrote:
>>>>
>>>>>
>>>>>   Hi,
>>>>>
>>>>>>
>>>>>>
>>>>>>> The following patches should fix your problem:
>>>>>>>
>>>>>>> https://svnweb.freebsd.org/changeset/base/275790
>>>>>>> https://svnweb.freebsd.org/changeset/base/275791
>>>>>>>
>>>>>>> --HPS
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>
>>>>>>  Can you get the dmesg when plugging your device?
>>>
>>> --HPS
>>>
>>>
>>>  uhid0: <Tripp Lite TRIPP LITE SMART1500RM2U, class 0/0, rev 1.10/2.0a,
>> addr 3> on usbus1
>> ugen1.3: <Tripp Lite> at usbus1 (disconnected)
>> uhid0: at uhub3, port 1, addr 3 (disconnected)
>> ugen1.3: <Tripp Lite> at usbus1
>> uhid0: <Tripp Lite TRIPP LITE SMART1500RM2U, class 0/0, rev 1.10/2.0a,
>> addr 3> on usbus1
>> ugen1.3: <Tripp Lite> at usbus1 (disconnected)
>> uhid0: at uhub3, port 1, addr 3 (disconnected)
>>
>> I tried putting the usb.conf in /etc/devd and rebooting, but no change..
>>
>>
> Hi,
>
> This looks correct. Did you select the correct device profile?
>
> Also, did you set the correct USB configuration number?
>
> usbconfig -d X.Y dump_device_desc dump_curr_config_desc
> usbconfig -d X.Y set_config 1
>
> --HPS
>

I ran the set_config 1, but that didn't have any effect, nor did set_config
0.   the dump device & config is below.

I did not select any profile, I just plug the unit in and I get the
disconnect messages.

ugen1.3: <TRIPP LITE SMART1500RM2U Tripp Lite> at usbus1, cfg=0
md=HOST spd=LOW (1.5Mbps) pwr=ON (0mA)

  bLength = 0x0012
  bDescriptorType = 0x0001
  bcdUSB = 0x0110
  bDeviceClass = 0x0000
  bDeviceSubClass = 0x0000
  bDeviceProtocol = 0x0000
  bMaxPacketSize0 = 0x0008
  idVendor = 0x09ae
  idProduct = 0x3015
  bcdDevice = 0x020a
  iManufacturer = 0x0002  <Tripp Lite >
  iProduct = 0x0003  <TRIPP LITE SMART1500RM2U >
  iSerialNumber = 0x0004  <2351BY0SM820600181>
  bNumConfigurations = 0x0001


 Configuration index 0

    bLength = 0x0009
    bDescriptorType = 0x0002
    wTotalLength = 0x0022
    bNumInterfaces = 0x0001
    bConfigurationValue = 0x0001
    iConfiguration = 0x0000  <no string>
    bmAttributes = 0x00e0
    bMaxPower = 0x0000

    Interface 0
      bLength = 0x0009
      bDescriptorType = 0x0004
      bInterfaceNumber = 0x0000
      bAlternateSetting = 0x0000
      bNumEndpoints = 0x0001
      bInterfaceClass = 0x0003
      bInterfaceSubClass = 0x0000
      bInterfaceProtocol = 0x0000
      iInterface = 0x0000  <no string>

      Additional Descriptor

      bLength = 0x09
      bDescriptorType = 0x21
      bDescriptorSubType = 0x10
       RAW dump:
       0x00 | 0x09, 0x21, 0x10, 0x01, 0x00, 0x01, 0x22, 0xe4,
       0x08 | 0x04

      Endpoint 0

      bLength = 0x0007
      bDescriptorType = 0x0005
      bEndpointAddress = 0x0081  <IN>
      bmAttributes = 0x0003  <INTERRUPT>
      wMaxPacketSize = 0x0008
      bInterval = 0x0028
      bRefresh = 0x0000
      bSynchAddress = 0x0000
_______________________________________________
freebsd-usb@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-usb
To unsubscribe, send any mail to "freebsd-usb-unsubscr...@freebsd.org"

Reply via email to