Hi John,

On Fri, Dec 27, 2013 at 9:05 AM, John Baldwin <j...@freebsd.org> wrote:
> While hacking on the power button support, I also started rototilling the DSDT
> generation code a bit.  My initial goal was to enumerate the LPC serial ports
> (COM1 and COM2) properly via ACPI.  I ended up doing the following:
>
> - Moved the info for the top-level PCI bus into the PCI emulation code and
>   added ResourceProducer entries for the memory ranges decoded by the bus
>   for memory BARs.
> - I added a framework to allow each PCI emulation driver to optionally write
>   an entry into the DSDT under the \_SB_.PCI0 namespace.  The LPC driver uses
>   this to write a node for the LPC bus (\_SB_.PCI0.ISA).
> - I added a linker set to allow any LPC devices to write entries into the
>   DSDT below the LPC node.  I moved the existing block for the RTC out of
>   acpi.c and into the RTC driver.  I added DSDT nodes for the AT PIC,
>   the 8254 ISA timer, and the LPC UART devices.
> - I also added a "SuperIO" device under the LPC node to claim "system
>   resources" (as is done in real hardware).  I added a linker set to allow
>   various drivers to add IO or memory ranges that should be claimed by
>   SuperIO and then added the extended RTC IO range and the registers used
>   for ACPI power management as system resources.
>
> The end result is that for the stock VM created by vmrun.sh, the attimer0,
> uart0, and uart1 devices move from isa0 to acpi0.  There is also a PIC
> device that would be claimed by 'device atpic' (but the stock amd64 kernel
> doesn't include that).  The DSDT is also a bit more fleshed out, and also
> looks "nice" as devices are mostly laid out in the normal tree rather than
> using separate Scope() sections for each device.
>
> Note that I did add some helper routines for writing out DSDT lines and
> resource entries to try to simplify the code in the various DSDT handlers
> and make the code that generates DSDT lines a bit more readable (e.g. the
> implicit newlines make things more readable IMO).
>
> The patch is relative to the previous power button patch and is at
> http://www.FreeBSD.org/~jhb/patches/bhyve_dsdt.patch

I am getting a "404 Not Found" at this URL.

best
Neel

>
> Assuming these are ok, the next thing I might work on is cleaning up
> the PCI INTx interrupts.  They should really all be rounted to the I/O APIC
> intpins above 15 (and we should leave ISA IRQs 5, 10, and 11 alone in APIC
> mode and only fall back to that if we are using the 8259As and a real ELCR).
> The MP Table output would need some minor tweaking for that, and for ACPI we
> should generate a _PRT table under _SB_.PCI0 in pci_emul.c.
>
> --
> John Baldwin
> _______________________________________________
> freebsd-virtualization@freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-virtualization
> To unsubscribe, send any mail to 
> "freebsd-virtualization-unsubscr...@freebsd.org"
_______________________________________________
freebsd-virtualization@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-virtualization
To unsubscribe, send any mail to 
"freebsd-virtualization-unsubscr...@freebsd.org"

Reply via email to