Is hat in one config file? Or two hostapd config files?
-a On 3 June 2014 11:30, Harm Weites <h...@weites.com> wrote: > Hi, > > While trying to setup an AP with two SSID's I ran into some issues. > > Environment: > TP-Link 1043ND (MIPS) > ath0 ether 00:19:e0:66:66:68 > wlan0 ether 02:ab:cd:ef:12:30 > wlan1 ether 00:19:e0:66:66:68 > > Both wlan0 and wlan1 have been created with wlandev ath0 and wlanmode > hostap. The goal is to have one guest wifi network, locked down using pf > and having a proper wifi network using radius for personal use (thus, > without pf). > > This is the hostapd config: > > # > ctrl_interface=/var/run/hostapd > hw_mode=g > > bss=wlan0 > interface=wlan0 > driver=bsd > ssid=gasten > wpa=3 > wpa_key_mgmt=WPA-PSK > wpa_passphrase=comegetsome > wpa_pairwise=CCMP > > bss=wlan1 > driver=bsd > ssid=prive > wpa=1 > wpa_key_mgmt=WPA-EAP > wpa_pairwise=TKIP > wpa_group_rekey=300 > wpa_gmk_rekey=640 > ieee8021x=1 > auth_algs=1 > eapol_key_index_workaround=1 > own_ip_addr=127.0.0.1 > nas_identifier=wifi.example.com > auth_server_addr=10.65.0.130 > auth_server_port=1812 > auth_server_shared_secret=secret > acct_server_addr=10.65.0.130 > acct_server_port=1813 > acct_server_shared_secret=secret > # > > Now, hostapd complains about the following: > > Configuration file: /etc/hostapd.conf > Using interface wlan0 with hwaddr 02:ab:cd:ef:12:30 and ssid "gasten" > Failed to add BSS (BSSID=02:ab:cd:ef:12:31) > wlan0: Unable to setup interface. > Failed to remove BSS interface wlan0 > > Thats it for having multiple (2) SSID's. > > Now, the 2nd issue: radius. For this, I've disabled the passphrase'd > SSID to have just one (working) SSID. > > I haven't given the backend much attention just yet, but I'm seeing the > following error after trying to associate: > > wlan0: STA a8:16:b2:54:9c:ef IEEE 802.11: associated > wlan0: CTRL-EVENT-EAP-STARTED a8:16:b2:54:9c:ef > wlan0: CTRL-EVENT-EAP-PROPOSED-METHOD vendor=0 method=1 > wlan0: STA a8:16:b2:54:9c:ef IEEE 802.11: disassociated > ioctl[SIOCS80211, op=20, val=0, arg_len=7]: No such file or directory > ioctl[SIOCS80211, op=20, val=0, arg_len=7]: No such file or directory > > This is using an Android device, with PEAP. I haven't got a clue yet on > which mode I should be using, or how to configure that but since I'm > seeing a 'No such file or directory' I'm afraid something needs to be > resolved before diving into the final configuration (if this was about > cert/key files, shouldn't it just explicitly say it's missing just > that?). Attached to this message is some debug output from hostapd from > the connection attempt. > > Regards, > Harm > _______________________________________________ > email@example.com mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-wireless > To unsubscribe, send any mail to "freebsd-wireless-unsubscr...@freebsd.org" _______________________________________________ firstname.lastname@example.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-wireless To unsubscribe, send any mail to "freebsd-wireless-unsubscr...@freebsd.org"