Ola, Não se vc ja fez mas tente desabilitar o ACPI.
Cleber Medina Em 24/06/2011 08:48, Marcelo Gondim escreveu: > Opa Paulo, > > Peguei o equipamento ontem e nada. Não consegui resolver ainda. Mesmo > com o FreeBSD 8.2-STABLE o equipamento se auto desliga randomicamente. > Abaixo o dmesg dela: > > Copyright (c) 1992-2011 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 8.2-STABLE #0: Thu Jun 23 04:13:40 BRT 2011 > [email protected]:/usr/obj/usr/src/sys/GONDIM amd64 > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Intel(R) Xeon(R) CPU E5606 @ 2.13GHz (2133.32-MHz > K8-class CPU) > Origin = "GenuineIntel" Id = 0x206c2 Family = 6 Model = 2c > Stepping = 2 > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > > Features2=0x29ee3ff<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,DCA,SSE4.1,SSE4.2,POPCNT,AESNI> > AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM> > AMD Features2=0x1<LAHF> > TSC: P-state invariant > real memory = 8589934592 (8192 MB) > avail memory = 8150536192 (7772 MB) > ACPI APIC Table:<INTEL S5500BC> > FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs > FreeBSD/SMP: 2 package(s) x 4 core(s) > cpu0 (BSP): APIC ID: 0 > cpu1 (AP): APIC ID: 2 > cpu2 (AP): APIC ID: 18 > cpu3 (AP): APIC ID: 20 > cpu4 (AP): APIC ID: 32 > cpu5 (AP): APIC ID: 34 > cpu6 (AP): APIC ID: 50 > cpu7 (AP): APIC ID: 52 > ioapic0<Version 2.0> irqs 0-23 on motherboard > ioapic1<Version 2.0> irqs 24-47 on motherboard > lapic0: Forcing LINT1 to edge trigger > kbd1 at kbdmux0 > cryptosoft0:<software crypto> on motherboard > acpi0:<INTEL S5500BC> on motherboard > acpi0: [ITHREAD] > acpi0: Power Button (fixed) > Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 > acpi_timer0:<24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 > cpu0:<ACPI CPU> on acpi0 > cpu1:<ACPI CPU> on acpi0 > cpu2:<ACPI CPU> on acpi0 > cpu3:<ACPI CPU> on acpi0 > cpu4:<ACPI CPU> on acpi0 > cpu5:<ACPI CPU> on acpi0 > cpu6:<ACPI CPU> on acpi0 > cpu7:<ACPI CPU> on acpi0 > pcib0:<ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0:<ACPI PCI bus> on pcib0 > pcib1:<ACPI PCI-PCI bridge> irq 28 at device 1.0 on pci0 > pci1:<ACPI PCI bus> on pcib1 > em0:<Intel(R) PRO/1000 Network Connection 7.2.3> port 0x1000-0x101f mem > 0xb1a00000-0xb1a1ffff,0xb1900000-0xb19fffff,0xb1a20000-0xb1a23fff irq 28 > at device 0.0 on pci1 > em0: Using MSIX interrupts with 3 vectors > em0: [ITHREAD] > em0: [ITHREAD] > em0: [ITHREAD] > em0: Ethernet address: 00:1e:67:07:9d:cd > pcib2:<ACPI PCI-PCI bridge> irq 24 at device 3.0 on pci0 > pci2:<ACPI PCI bus> on pcib2 > pcib3:<ACPI PCI-PCI bridge> irq 30 at device 7.0 on pci0 > pci3:<ACPI PCI bus> on pcib3 > pcib4:<ACPI PCI-PCI bridge> irq 32 at device 9.0 on pci0 > pci4:<ACPI PCI bus> on pcib4 > pci0:<base peripheral, interrupt controller> at device 16.0 (no driver > attached) > pci0:<base peripheral, interrupt controller> at device 16.1 (no driver > attached) > pci0:<base peripheral, interrupt controller> at device 17.0 (no driver > attached) > pci0:<base peripheral, interrupt controller> at device 17.1 (no driver > attached) > pci0:<base peripheral, interrupt controller> at device 20.0 (no driver > attached) > pci0:<base peripheral, interrupt controller> at device 20.1 (no driver > attached) > pci0:<base peripheral, interrupt controller> at device 20.2 (no driver > attached) > pci0:<base peripheral, interrupt controller> at device 20.3 (no driver > attached) > pci0:<base peripheral> at device 22.0 (no driver attached) > pci0:<base peripheral> at device 22.1 (no driver attached) > pci0:<base peripheral> at device 22.2 (no driver attached) > pci0:<base peripheral> at device 22.3 (no driver attached) > pci0:<base peripheral> at device 22.4 (no driver attached) > pci0:<base peripheral> at device 22.5 (no driver attached) > pci0:<base peripheral> at device 22.6 (no driver attached) > pci0:<base peripheral> at device 22.7 (no driver attached) > em1:<Intel(R) PRO/1000 Network Connection 7.2.3> port 0x20e0-0x20ff mem > 0xb1b00000-0xb1b1ffff,0xb1b43000-0xb1b43fff irq 20 at device 25.0 on pci0 > em1: Using an MSI interrupt > em1: [FILTER] > em1: Ethernet address: 00:1e:67:07:9d:cc > uhci0:<Intel 82801JI (ICH10) USB controller USB-D> port 0x20c0-0x20df > irq 19 at device 26.0 on pci0 > uhci0: [ITHREAD] > usbus0:<Intel 82801JI (ICH10) USB controller USB-D> on uhci0 > uhci1:<Intel 82801JI (ICH10) USB controller USB-E> port 0x20a0-0x20bf > irq 19 at device 26.1 on pci0 > uhci1: [ITHREAD] > usbus1:<Intel 82801JI (ICH10) USB controller USB-E> on uhci1 > uhci2:<Intel 82801JI (ICH10) USB controller USB-F> port 0x2080-0x209f > irq 19 at device 26.2 on pci0 > uhci2: [ITHREAD] > usbus2:<Intel 82801JI (ICH10) USB controller USB-F> on uhci2 > ehci0:<Intel 82801JI (ICH10) USB 2.0 controller USB-B> mem > 0xb1b41000-0xb1b413ff irq 19 at device 26.7 on pci0 > ehci0: [ITHREAD] > usbus3: EHCI version 1.0 > usbus3:<Intel 82801JI (ICH10) USB 2.0 controller USB-B> on ehci0 > pcib5:<ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 > pci5:<ACPI PCI bus> on pcib5 > pcib6:<ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0 > pci6:<ACPI PCI bus> on pcib6 > vgapci0:<VGA-compatible display> mem > 0xb0000000-0xb0ffffff,0xb1800000-0xb1803fff,0xb1000000-0xb17fffff irq 16 > at device 0.0 on pci6 > uhci3:<Intel 82801JI (ICH10) USB controller USB-A> port 0x2060-0x207f > irq 16 at device 29.0 on pci0 > uhci3: [ITHREAD] > usbus4:<Intel 82801JI (ICH10) USB controller USB-A> on uhci3 > uhci4:<Intel 82801JI (ICH10) USB controller USB-B> port 0x2040-0x205f > irq 16 at device 29.1 on pci0 > uhci4: [ITHREAD] > usbus5:<Intel 82801JI (ICH10) USB controller USB-B> on uhci4 > uhci5:<Intel 82801JI (ICH10) USB controller USB-C> port 0x2020-0x203f > irq 16 at device 29.2 on pci0 > uhci5: [ITHREAD] > usbus6:<Intel 82801JI (ICH10) USB controller USB-C> on uhci5 > ehci1:<Intel 82801JI (ICH10) USB 2.0 controller USB-A> mem > 0xb1b40000-0xb1b403ff irq 16 at device 29.7 on pci0 > ehci1: [ITHREAD] > usbus7: EHCI version 1.0 > usbus7:<Intel 82801JI (ICH10) USB 2.0 controller USB-A> on ehci1 > pcib7:<ACPI PCI-PCI bridge> at device 30.0 on pci0 > pci7:<ACPI PCI bus> on pcib7 > isab0:<PCI-ISA bridge> at device 31.0 on pci0 > isa0:<ISA bus> on isab0 > atapci0:<Intel ICH10 SATA300 controller> port > 0x2158-0x215f,0x216c-0x216f,0x2150-0x2157,0x2168-0x216b,0x2130-0x213f,0x2120-0x212f > irq 18 at device 31.2 on pci0 > atapci0: [ITHREAD] > ata2:<ATA channel 0> on atapci0 > ata2: [ITHREAD] > ata3:<ATA channel 1> on atapci0 > ata3: [ITHREAD] > pci0:<serial bus, SMBus> at device 31.3 (no driver attached) > atapci1:<Intel ICH10 SATA300 controller> port > 0x2148-0x214f,0x2164-0x2167,0x2140-0x2147,0x2160-0x2163,0x2110-0x211f,0x2100-0x210f > irq 21 at device 31.5 on pci0 > atapci1: [ITHREAD] > ata4:<ATA channel 0> on atapci1 > ata4: [ITHREAD] > ata5:<ATA channel 1> on atapci1 > ata5: [ITHREAD] > acpi_button0:<Sleep Button> on acpi0 > atrtc0:<AT realtime clock> port 0x70-0x71,0x74-0x77 irq 8 on acpi0 > acpi_hpet0:<High Precision Event Timer> iomem 0xfed00000-0xfed003ff on > acpi0 > Timecounter "HPET" frequency 14318180 Hz quality 900 > qpi0:<QPI system bus> on motherboard > pcib8:<QPI Host-PCI bridge> pcibus 255 on qpi0 > pci255:<PCI bus> on pcib8 > pcib9:<QPI Host-PCI bridge> pcibus 254 on qpi0 > pci254:<PCI bus> on pcib9 > orm0:<ISA Option ROMs> at iomem > 0xc0000-0xc7fff,0xc8000-0xc8fff,0xc9000-0xc9fff on isa0 > atkbd: unable to set the command byte. > sc0:<System console> at flags 0x100 on isa0 > sc0: VGA<16 virtual consoles, flags=0x300> > vga0:<Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > atkbdc0:<Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0:<AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > atkbd0: [ITHREAD] > psm0: unable to set the command byte. > est0:<Enhanced SpeedStep Frequency Control> on cpu0 > p4tcc0:<CPU Frequency Thermal Control> on cpu0 > est1:<Enhanced SpeedStep Frequency Control> on cpu1 > p4tcc1:<CPU Frequency Thermal Control> on cpu1 > est2:<Enhanced SpeedStep Frequency Control> on cpu2 > p4tcc2:<CPU Frequency Thermal Control> on cpu2 > est3:<Enhanced SpeedStep Frequency Control> on cpu3 > p4tcc3:<CPU Frequency Thermal Control> on cpu3 > est4:<Enhanced SpeedStep Frequency Control> on cpu4 > p4tcc4:<CPU Frequency Thermal Control> on cpu4 > est5:<Enhanced SpeedStep Frequency Control> on cpu5 > p4tcc5:<CPU Frequency Thermal Control> on cpu5 > est6:<Enhanced SpeedStep Frequency Control> on cpu6 > p4tcc6:<CPU Frequency Thermal Control> on cpu6 > est7:<Enhanced SpeedStep Frequency Control> on cpu7 > p4tcc7:<CPU Frequency Thermal Control> on cpu7 > Timecounters tick every 1.000 msec > IPsec: Initialized Security Association Processing. > ipfw2 (+ipv6) initialized, divert enabled, nat enabled, rule-based > forwarding enabled, default to accept, logging disabled > DUMMYNET 0 with IPv6 initialized (100409) > load_dn_sched dn_sched FIFO loaded > load_dn_sched dn_sched PRIO loaded > load_dn_sched dn_sched QFQ loaded > load_dn_sched dn_sched RR loaded > load_dn_sched dn_sched WF2Q+ loaded > usbus0: 12Mbps Full Speed USB v1.0 > usbus1: 12Mbps Full Speed USB v1.0 > usbus2: 12Mbps Full Speed USB v1.0 > usbus3: 480Mbps High Speed USB v2.0 > usbus4: 12Mbps Full Speed USB v1.0 > usbus5: 12Mbps Full Speed USB v1.0 > usbus6: 12Mbps Full Speed USB v1.0 > usbus7: 480Mbps High Speed USB v2.0 > ugen0.1:<Intel> at usbus0 > uhub0:<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 > ugen1.1:<Intel> at usbus1 > uhub1:<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 > ugen2.1:<Intel> at usbus2 > uhub2:<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 > ugen3.1:<Intel> at usbus3 > uhub3:<Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3 > ugen4.1:<Intel> at usbus4 > uhub4:<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4 > ugen5.1:<Intel> at usbus5 > uhub5:<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5 > ugen6.1:<Intel> at usbus6 > uhub6:<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6 > ugen7.1:<Intel> at usbus7 > uhub7:<Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7 > ad4: 953869MB<Seagate ST31000528AS CC44> at ata2-master UDMA100 SATA 3Gb/s > acd0: DVDR<HL-DT-ST DVDRAM GH22NS50/TN03> at ata3-master UDMA100 SATA > 1.5Gb/s > lapic20: Forcing LINT1 to edge trigger > SMP: AP CPU #3 Launched! > lapic34: Forcing LINT1 to edge trigger > SMP: AP CPU #5 Launched! > lapic2: Forcing LINT1 to edge trigger > SMP: AP CPU #1 Launched! > lapic52: Forcing LINT1 to edge trigger > SMP: AP CPU #7 Launched! > lapic18: Forcing LINT1 to edge trigger > SMP: AP CPU #2 Launched! > lapic32: Forcing LINT1 to edge trigger > SMP: AP CPU #4 Launched! > lapic50: Forcing LINT1 to edge trigger > SMP: AP CPU #6 Launched! > Root mount waiting for: usbus7 usbus6 usbus5 usbus4 usbus3 usbus2 usbus1 > usbus0 > uhub0: 2 ports with 2 removable, self powered > uhub1: 2 ports with 2 removable, self powered > uhub2: 2 ports with 2 removable, self powered > uhub4: 2 ports with 2 removable, self powered > uhub5: 2 ports with 2 removable, self powered > uhub6: 2 ports with 2 removable, self powered > Root mount waiting for: usbus7 usbus3 > Root mount waiting for: usbus7 usbus3 > uhub3: 6 ports with 6 removable, self powered > uhub7: 6 ports with 6 removable, self powered > Trying to mount root from ufs:/dev/ad4s1a > WARNING: / was not properly dismounted > ugen0.2:<CHESEN> at usbus0 > ukbd0:<CHESEN USB Keyboard, class 0/0, rev 1.10/1.10, addr 2> on usbus0 > kbd2 at ukbd0 > uhid0:<CHESEN USB Keyboard, class 0/0, rev 1.10/1.10, addr 2> on usbus0 > ugen2.2:<American Megatrends Inc.> at usbus2 > ukbd1:<Keyboard Interface> on usbus2 > kbd3 at ukbd1 > ums0:<Mouse Interface> on usbus2 > ums0: 3 buttons and [Z] coordinates ID=0 > WARNING: /tmp was not properly dismounted > WARNING: /usr was not properly dismounted > WARNING: /var was not properly dismounted > em0: link state changed to UP > > Esses warning é porque ela desliga do nada e aí obviamente lá vai um > fsck e pior que demora pacas porque o disco é de 1Tb. > > Em 17/06/2011 17:32, Paulo Henrique - BSDs Brasil escreveu: >> Tem algum dmesg para poder ver o que a placa-mãe possui. >> NO site da intel a descrićão é muito resumida, o que diz que ela possui >> o que de fato o FreeBSD suporta, não sei quanto IPMI2.0. >> Att. >> Marcelo Gondim wrote: >>> Em 17/06/2011 15:21, Paulo Henrique - BSDs Brasil escreveu: >>> >>>> Inicia o FreeBSD em modo debug e manda a saida para nós. >>>> Informaćão quanto ao solucionamento importantissima para a lista. >>>> >>>> Att. >>>> >>>> >>> Opa Paulo, >>> >>> Vou tentar mas o problema dá randomicamente. O sistema inicia normal, >>> fica lá no login tranqüilo e do nada desliga e liga. >>> Mas com certeza descobrindo uma solução estarei postando aqui. O >>> equipamento está agora em um laboratório no Rio em testes para >>> descobrirmos o motivo ou pelo menos tentarmos. >>> >>> >>>> Marcelo Gondim wrote: >>>> >>>>> Olá pessoal, >>>>> >>>>> Comprei um equipamento dual Quad Xeon e esse usa uma motherboard >>>>> S5500BCR que é dual processada. O que ocorre é o seguinte: >>>>> >>>>> Na instalação do FreeBSD 8.2-release a máquina simplesmente desliga dá >>>>> uns apitos indicando problema e re-inicia novamente sozinha. Consegui >>>>> com muito custo terminar a instalação do sistema mas não estou >>>>> conseguindo atualizar para a versão 8.2-stable porque ela sempre >>>>> re-inicia antes mesmo de eu completar. Sei que muitos vão achar que é um >>>>> problema no hardware ou elétrica, também achei isso e troquei fonte, >>>>> memória, processador e até a motherboard e nada resolveu. Testei com >>>>> outros sistemas como windows 2008 e linux e o problema não ocorre mas >>>>> com o FreeBSD está acontecendo isso. Alguém faz idéia do que seja? >>>>> Porque procurei nos logs e não vi nada, dmesg também nada. >>>>> Estou pensando em tirar o hd, colocar em outro equipamento, atualizar >>>>> para a 8.2-stable e colocar de volta para ver se acontece o mesmo >>>>> problema. >>>>> >>>>> Alguém passou por esse pepino? >>>>> >>>>> []´s >>>>> >>>>> Gondim >>>>> ------------------------- >>>>> Histórico:http://www.fug.com.br/historico/html/freebsd/ >>>>> Sair da lista:https://www.fug.com.br/mailman/listinfo/freebsd >>>>> >>>>> >>>> ------------------------- >>>> Histórico:http://www.fug.com.br/historico/html/freebsd/ >>>> Sair da lista:https://www.fug.com.br/mailman/listinfo/freebsd >>>> >>> ------------------------- >>> Histórico:http://www.fug.com.br/historico/html/freebsd/ >>> Sair da lista:https://www.fug.com.br/mailman/listinfo/freebsd >>> >> ------------------------- >> Histórico:http://www.fug.com.br/historico/html/freebsd/ >> Sair da lista:https://www.fug.com.br/mailman/listinfo/freebsd > ------------------------- > Histórico:http://www.fug.com.br/historico/html/freebsd/ > Sair da lista:https://www.fug.com.br/mailman/listinfo/freebsd ------------------------- Histórico: http://www.fug.com.br/historico/html/freebsd/ Sair da lista: https://www.fug.com.br/mailman/listinfo/freebsd
