Hi again, the customer just sent me also bmc-info of another system with X8DT3-LN4F board - see http://www.supermicro.com/products/motherboard/QPI/5500/X8DT3-LN4F.cfm
The X8DT3-LN4F also lacks output for CPU temperatures. Here is its bmc-info: Device ID : 32 Device Revision : 1 Device SDRs : unsupported Firmware Revision : 2.03 Device Available : yes (normal operation) IPMI Version : 2.0 Sensor Device : supported SDR Repository Device : supported SEL Device : supported FRU Inventory Device : supported IPMB Event Receiver : supported IPMB Event Generator : supported Bridge : unsupported Chassis Device : supported Manufacturer ID : Super Micro Computer Inc. (47488) Product ID : 43707 Auxiliary Firmware Revision Information : 00000001h GUID : 00000000-0000-0000-0000-000000434D53 System Firmware Version : rsion1.0 System Name : Manager Primary Operating System Name : SE Server 1.0 Operating System Name : Channel Information Channel Number : 0 Medium Type : IPMB (I2C) Protocol Type : IPMB-1.0 Active Session Count : 0 Session Support : session-less Vendor ID : Intelligent Platform Management Interface forum (7154) Channel Number : 1 Medium Type : 802.3 LAN Protocol Type : IPMB-1.0 Active Session Count : 1 Session Support : multi-session Vendor ID : Intelligent Platform Management Interface forum (7154) best regards, Werner On Mon, 2011-02-14 at 11:33 +0100, Werner Fischer wrote: > Hi Al, > > * one of our customers discovered another Supermicro system where > FreeIPMI has currently no product ID information to display the > OEM CPU temp sensors (he tried up to > freeipmi-1.0.2.beta2.tar.gz) > * It is a 6015B-3R > http://www.supermicro.com/products/system/1U/6015/SYS-6015B-3R.cfm > with a X7DBR-3 mainboard > http://www.supermicro.com/products/motherboard/Xeon1333/5000P/X7DBR-3.cfm > Below I have attached his output of bmc-info. > > My questions > 1. Can you add the Manufacturer-ID/Product-ID for the OEM CPU temp > sensors for this board? (As it is a X7-board it has IPMI not > onboard (like the X8-boards do), but it uses the AOC-SIMSO(+) > add on card for IPMI. Therefore the Manufacturer ID is Peppercon > (not Supermicro).) > 2. If it is not too difficult for me and if it could lower your > necessary work: Maybe you can tell me where the > Manufacturer-ID/Product-ID are matched in the FreeIPMI code for > the OEM sensors (so I could try add them myself in the source > and I could send you directly patches) > > Thanks for your help and best regards, > Werner > > PS: Here is the output of bmc-info: > > Device ID : 34 > Device Revision : 1 > Device SDRs : unsupported > Firmware Revision : 1.59 > Device Available : yes (normal operation) > IPMI Version : 2.0 > Sensor Device : supported > SDR Repository Device : supported > SEL Device : supported > FRU Inventory Device : supported > IPMB Event Receiver : unsupported > IPMB Event Generator : unsupported > Bridge : unsupported > Chassis Device : supported > Manufacturer ID : Peppercon AG (10437) > Product ID : 4 > Auxiliary Firmware Revision Information : 20540000h > > GUID : 0F0E0D0C-0B0A-0908-BD20-9BFEFF483002 > > Channel Information > > Channel Number : 1 > Medium Type : 802.3 LAN > Protocol Type : IPMB-1.0 > Active Session Count : 1 > Session Support : multi-session > Vendor ID : Intelligent Platform Management Interface forum > (7154) > > Channel Number : 5 > Medium Type : Asynch. Serial/Modem (RS-232) > Protocol Type : IPMB-1.0 > Active Session Count : 0 > Session Support : single-session > Vendor ID : Intelligent Platform Management Interface forum > (7154) > > _______________________________________________ Freeipmi-devel mailing list [email protected] http://lists.gnu.org/mailman/listinfo/freeipmi-devel
