Good day! I ve got radius server installed on my FreeBSD.
All auth logs i receive from Cisco router stored in MYSQL DB
Here the info i write down in mysql :
example :
NAS-IP-Address = 192.168.200.8
NAS-Port = 179
Cisco-NAS-Port = "Async179"
NAS-Port-Type = Async
User-Name = "depcomcor"
Acct-Status-Type = Stop
Acct-Authentic = RADIUS
Service-Type = Framed-User
Acct-Session-Id = "00000413"
Framed-Protocol = PPP
Framed-IP-Address = 192.168.223.6
Acct-Terminate-Cause = Lost-Carrier
Acct-Input-Octets = 188282
Acct-Output-Octets = 257069
Acct-Input-Packets = 884
Acct-Output-Packets = 916
Acct-Session-Time = 541
//its all ok till this moment
How i should configure sql.conf to store subordinate info??
Cisco-AVPair = "disc-cause-ext=1011"
Cisco-AVPair = "pre-bytes-in=112"
Cisco-AVPair = "pre-bytes-out=171"
Cisco-AVPair = "pre-paks-in=4"
Cisco-AVPair = "pre-paks-out=8"
Cisco-AVPair = "pre-session-time=51"
Cisco-AVPair = "connect-progress=60"
Cisco-AVPair = "nas-rx-speed=26400"
Cisco-AVPair = "nas-tx-speed=12000"
Acct-Delay-Time = 0
Here my config
----------------------------------------------------------------------
# The database schema is available at:
#
# src/radiusd/src/modules/rlm_sql/drivers/rlm_sql_mysql/db_mysql.sql
#
# If you are using PostgreSQL, please use 'postgresql.conf', instead.
# If you are using Oracle, please use 'oracle.conf', instead.
# If you are using MS-SQL, please use 'mssql.conf', instead.
#
# $Id: sql.conf,v 1.26 2002/11/18 15:32:03 aland Exp $
#
sql {
# Database type
# Current supported are: rlm_sql_mysql, rlm_sql_postgresql,
# rlm_sql_iodbc, rlm_sql_oracle, rlm_sql_unixodbc, rlm_sql_freetds
driver = "rlm_sql_mysql"
# Connect info
server = "****"
login = "***"
password = "***"
# Database table configuration
radius_db = "radius"
# If you want both stop and start records logged to the
# same SQL table, leave this as is. If you want them in
# different tables, put the start table in acct_table1
# and stop table in acct_table2
acct_table1 = "radacct"
acct_table2 = "radacct"
authcheck_table = "radcheck"
authreply_table = "radreply"
groupcheck_table = "radgroupcheck"
groupreply_table = "radgroupreply"
usergroup_table = "usergroup"
# Remove stale session if checkrad does not see a double login
deletestalesessions = yes
# Print all SQL statements when in debug mode (-x)
sqltrace = no
sqltracefile = ${logdir}/sqltrace.sql
# number of sql connections to make to server
num_sql_socks = 5
# number of seconds to dely retrying on a failed database
# connection (per_socket)
connect_failure_retry_delay = 60
#######################################################################
# Query config: Username
#######################################################################
# This is the username that will get substituted, escaped, and added
# as attribute 'SQL-User-Name'. '%{SQL-User-Name}' should be used below
# everywhere a username substitution is needed so you you can be sure
# the username passed from the client is escaped properly.
#
# Uncomment the next line, if you want the sql_user_name to mean:
#
# Use Stripped-User-Name, if it's there.
# Else use User-Name, if it's there,
# Else use hard-coded string "DEFAULT" as the user name.
#sql_user_name = "%{Stripped-User-Name:-%{User-Name:-DEFAULT}}"
#
sql_user_name = "%{User-Name}"
#######################################################################
# Default profile
#######################################################################
# This is the default profile. It is found in SQL by group membership.
# That means that this profile must be a member of at least one group
# which will contain the corresponding check and reply items.
# This profile will be queried in the authorize section for every user.
# The point is to assign all users a default profile without having to
# manually add each one to a group that will contain the profile.
# The SQL module will also honor the User-Profile attribute. This
# attribute can be set anywhere in the authorize section (ie the users
# file). It is found exactly as the default profile is found.
# If it is set then it will *overwrite* the default profile setting.
# The idea is to select profiles based on checks on the incoming packets,
# not on user group membership. For example:
# -- users file --
# DEFAULT Service-Type == Outbound-User, User-Profile := "outbound"
# DEFAULT Service-Type == Framed-User, User-Profile := "framed"
#
# By default the default_user_profile is not set
#
#default_user_profile = "DEFAULT"
#
# Determines if we will query the default_user_profile or the User-Profile
# if the user is not found. If the profile is found then we consider the user
# found. By default this is set to 'no'.
#
#query_on_not_found = no
#######################################################################
# Authorization Queries
#######################################################################
# These queries compare the check items for the user
# in ${authcheck_table} and setup the reply items in
# ${authreply_table}. You can use any query/tables
# you want, but the return data for each row MUST
# be in the following order:
#
# 0. Row ID (currently unused)
# 1. UserName/GroupName
# 2. Item Attr Name
# 3. Item Attr Value
# 4. Item Attr Operation
#######################################################################
# Use these for case sensitive usernames. WARNING: Slower queries!
# authorize_check_query = "SELECT id,UserName,Attribute,Value,op FROM
${authcheck_table} WHERE STRCMP(Username,
'%{SQL-User-Name}') = 0 ORDER BY id"
# authorize_reply_query = "SELECT id,UserName,Attribute,Value,op FROM
${authreply_table} WHERE STRCMP(Username,
'%{SQL-User-Name}') = 0 ORDER BY id"
authorize_check_query = "SELECT id,UserName,Attribute,Value,op FROM
${authcheck_table} WHERE Username =
'%{SQL-User-Name}' ORDER BY id"
authorize_reply_query = "SELECT id,UserName,Attribute,Value,op FROM
${authreply_table} WHERE Username =
'%{SQL-User-Name}' ORDER BY id"
# Use these for case sensitive usernames. WANRING: Slower queries!
# authorize_group_check_query = "SELECT
${groupcheck_table}.id,${groupcheck_table}.GroupName,${groupcheck_table}.Attribute,${groupcheck_table}.Value,${groupcheck_table}.op
FROM ${groupcheck_table},${usergroup_table} WHERE STRCMP(${usergroup_table}.Username,
'%{SQL-User-Name}') = 0 AND
${usergroup_table}.GroupName = ${groupcheck_table}.GroupName ORDER BY
${groupcheck_table}.id"
# authorize_group_reply_query = "SELECT
${groupreply_table}.id,${groupreply_table}.GroupName,${groupreply_table}.Attribute,${groupreply_table}.Value,${groupreply_table}.op
FROM ${groupreply_table},${usergroup_table} WHERE STRCMP(${usergroup_table}.Username,
'%{SQL-User-Name}') = 0 AND
${usergroup_table}.GroupName = ${groupreply_table}.GroupName ORDER BY
${groupreply_table}.id"
authorize_group_check_query = "SELECT
${groupcheck_table}.id,${groupcheck_table}.GroupName,${groupcheck_table}.Attribute,${groupcheck_table}.Value,${groupcheck_table}.op
FROM ${groupcheck_table},${usergroup_table} WHERE ${usergroup_table}.Username =
'%{SQL-User-Name}' AND
${usergroup_table}.GroupName = ${groupcheck_table}.GroupName ORDER BY
${groupcheck_table}.id"
authorize_group_reply_query = "SELECT
${groupreply_table}.id,${groupreply_table}.GroupName,${groupreply_table}.Attribute,${groupreply_table}.Value,${groupreply_table}.op
FROM ${groupreply_table},${usergroup_table} WHERE ${usergroup_table}.Username =
'%{SQL-User-Name}' AND
${usergroup_table}.GroupName = ${groupreply_table}.GroupName ORDER BY
${groupreply_table}.id"
#######################################################################
# Accounting Queries
#######################################################################
# accounting_onoff_query - query for Accounting On/Off packets
# accounting_update_query - query for Accounting update packets
# accounting_start_query - query for Accounting start packets
# accounting_start_query_alt - query for Accounting start packets
# (alternate in case first query fails)
# accounting_stop_query - query for Accounting stop packets
# accounting_stop_query_alt - query for Accounting start packets
# (alternate in case first query doesn't
# affect any existing rows in the table)
#######################################################################
accounting_onoff_query = "UPDATE ${acct_table1} SET AcctStopTime='%S',
AcctSessionTime=unix_timestamp('%S') -
unix_timestamp(AcctStartTime),
AcctTerminateCause=if('%{h323-call-type}'='VoIP','%{h323-disconnect-cause}','%{Acct-Terminate-Cause}',
AcctStopDelay =
%{Acct-Delay-Time} WHERE AcctSessionTime=0 AND AcctStopTime=0 AND NASIPAddress=
'%{NAS-IP-Address}' AND AcctStartTime <=
'%S'"
accounting_update_query = "UPDATE ${acct_table1} SET FramedIPAddress =
if('%{h323-call-type}'='VoIP','%{h323-remote-address}','%{Framed-IP-Address}') WHERE
AcctSessionId =
'%{Acct-Session-Id}' AND UserName = '%{SQL-User-Name}' AND NASIPAddress=
'%{NAS-IP-Address}' AND AcctStopTime = 0"
accounting_start_query = "INSERT into ${acct_table1} (RadAcctId,
AcctSessionId, AcctUniqueId, UserName, Realm,
NASIPAddress, NASPortId, NASPortType, AcctStartTime, AcctStopTime, AcctSessionTime,
AcctAuthentic, ConnectInfo_start,
ConnectInfo_stop, AcctInputOctets, AcctOutputOctets, CalledStationId,
CallingStationId, AcctTerminateCause, ServiceType,
FramedProtocol, FramedIPAddress, AcctStartDelay, AcctStopDelay, h323CallOrigin)
values('', '%{Acct-Session-Id}',
'%{Acct-Unique-Session-Id}', '%{SQL-User-Name}', '%{Realm}', '%{NAS-IP-Address}',
'%{NAS-Port}',
if('%{h323-call-type}'='VoIP','%{h323-call-type}','%{NAS-Port-Type}'), '%S', '0', '0',
'%{Acct-Authentic}',
'%{Connect-Info}', '', '0', '0', '%{Called-Station-Id}', '%{Calling-Station-Id}', '',
'%{Service-Type}',
'%{Framed-Protocol}',
if('%{h323-call-type}'='VoIP','%{h323-remote-address}','%{Framed-IP-Address}'),
'%{Acct-Delay-Time}', '0', '%{h323-call-origin}')"
accounting_start_query_alt = "UPDATE ${acct_table1} SET AcctStartTime = '%S',
AcctStartDelay =
'%{Acct-Delay-Time}', ConnectInfo_start = '%{Connect-Info}' WHERE AcctSessionId =
'%{Acct-Session-Id}' AND UserName =
'%{SQL-User-Name}' AND NASIPAddress = '%{NAS-IP-Address}' AND AcctStopTime = 0"
accounting_stop_query = "UPDATE ${acct_table2} SET AcctStopTime = '%S',
AcctSessionTime =
'%{Acct-Session-Time}', AcctInputOctets = '%{Acct-Input-Octets}', AcctOutputOctets =
'%{Acct-Output-Octets}',
AcctTerminateCause =
if('%{h323-call-type}'='VoIP','%{h323-disconnect-cause}','%{Acct-Terminate-Cause}'),
AcctStopDelay
= '%{Acct-Delay-Time}', ConnectInfo_stop = '%{Connect-Info}' WHERE AcctSessionId =
'%{Acct-Session-Id}' AND UserName =
'%{SQL-User-Name}' AND NASIPAddress = '%{NAS-IP-Address}' AND AcctStopTime = 0"
accounting_stop_query_alt = "INSERT into ${acct_table2} (RadAcctId,
AcctSessionId, AcctUniqueId, UserName,
Realm, NASIPAddress, NASPortId, NASPortType, AcctStartTime, AcctStopTime,
AcctSessionTime, AcctAuthentic,
ConnectInfo_start, ConnectInfo_stop, AcctInputOctets, AcctOutputOctets,
CalledStationId, CallingStationId,
AcctTerminateCause, ServiceType, FramedProtocol, FramedIPAddress, AcctStartDelay,
AcctStopDelay) values('',
'%{Acct-Session-Id}', '%{Acct-Unique-Session-Id}', '%{SQL-User-Name}', '%{Realm}',
'%{NAS-IP-Address}', '%{NAS-Port}',
if('%{h323-call-type}'='VoIP','%{h323-call-type}','%{NAS-Port-Type}'), '0', '%S',
'%{Acct-Session-Time}',
'%{Acct-Authentic}', '', '%{Connect-Info}', '%{Acct-Input-Octets}',
'%{Acct-Output-Octets}', '%{Called-Station-Id}',
'%{Calling-Station-Id}', '%{Acct-Terminate-Cause}', '%{Service-Type}',
'%{Framed-Protocol}',
if('%{h323-call-type}'='VoIP','%{h323-remote-address}','%{Framed-IP-Address}'), '0',
'%{Acct-Delay-Time}')"
#######################################################################
# Simultaneous Use Checking Queries
#######################################################################
# simul_count_query - query for the number of current connections
# - If this is not defined, no simultaneouls use
checking
# - will be performed by this module instance
# simul_verify_query - query to return details of current connections for
verification
# - Leave blank or commented out to disable verification
step
# - Note that the returned field order should not be
changed.
#######################################################################
# Uncomment simul_count_query to enable simultaneous use checking
simul_count_query = "SELECT COUNT(*) FROM ${acct_table1} WHERE
UserName='%{SQL-User-Name}' AND AcctStopTime = 0"
simul_verify_query = "SELECT RadAcctId, AcctSessionId, UserName, NASIPAddress,
NASPortId, FramedIPAddress,
CallingStationId, FramedProtocol FROM ${acct_table1} WHERE UserName='%{SQL-User-Name}'
AND AcctStopTime = 0"
#######################################################################
# Group Membership Queries
#######################################################################
# group_membership_query - Check user group membership
#######################################################################
group_membership_query = "SELECT GroupName FROM ${usergroup_table} WHERE
UserName='%{SQL-User-Name}'"
}
Thank you!
--
------------------------------------------------------------
Chelisant Pavel, System Administrator
MD2012, Chisinau, Moldova tel. (373 2) 504-693
str.Puskin 42 (373 2) 504-364
e-mail: [EMAIL PROTECTED], [EMAIL PROTECTED]
--------------------------------------------------------------
-
List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
