Hi,
I don't know how can i resolve my problem ...
With this user:
vlan3 Cisco-AVPair == "ssid=VLAN3", User-Password := "test"
Tunnel-Medium-Type = IEEE-802,
Tunnel-Private-Group-Id = 3,
Tunnel-Type = VLAN
I have always the same problem... this is my log:
rad_recv: Access-Request packet from host 192.168.9.104:1645, id=29,
length=240
User-Name = "vlan3"
Framed-MTU = 1400
Called-Station-Id = "0012.dacb.8420"
Calling-Station-Id = "000c.f135.f1ba"
Cisco-AVPair = "ssid=VLAN3"
Service-Type = Login-User
Message-Authenticator = 0x9873358109c27321d39f54fcaa44b983
EAP-Message =
0x0208005019001703010020abbfc50d6f7a13a8226e008a01441a4e94f2565c4eec010d12551692bfc9eea11703010020ea39080c7e56fafd97e7cb195e21a02a445b5632d50a356d96bf10a3082d53e2
NAS-Port-Type = Wireless-802.11
Cisco-NAS-Port = "263"
NAS-Port = 263
State = 0x1846e133758faf753fefeedfd54cc831
NAS-IP-Address = 192.168.9.104
NAS-Identifier = "ap"
Processing the authorize section of radiusd.conf
modcall: entering group authorize for request 7
modcall[authorize]: module "preprocess" returns ok for request 7
modcall[authorize]: module "mschap" returns noop for request 7
rlm_realm: No '@' in User-Name = "vlan3", looking up realm NULL
rlm_realm: No such realm "NULL"
modcall[authorize]: module "suffix" returns noop for request 7
rlm_eap: EAP packet type response id 8 length 80
rlm_eap: No EAP Start, assuming it's an on-going EAP conversation
modcall[authorize]: module "eap" returns updated for request 7
users: Matched entry vlan3 at line 24
modcall[authorize]: module "files" returns ok for request 7
modcall: leaving group authorize (returns updated) for request 7
rad_check_password: Found Auth-Type EAP
auth: type "EAP"
Processing the authenticate section of radiusd.conf
modcall: entering group authenticate for request 7
rlm_eap: Request found, released from the list
rlm_eap: EAP/peap
rlm_eap: processing type peap
rlm_eap_peap: Authenticate
rlm_eap_tls: processing TLS
eaptls_verify returned 7
rlm_eap_tls: Done initial handshake
eaptls_process returned 7
rlm_eap_peap: EAPTLS_OK
rlm_eap_peap: Session established. Decoding tunneled attributes.
rlm_eap_peap: Received EAP-TLV response.
rlm_eap_peap: Tunneled data is valid.
rlm_eap_peap: Had sent TLV failure. User was rejcted rejected
earlier in this session.
rlm_eap: Handler failed in EAP/peap
rlm_eap: Failed in EAP select
modcall[authenticate]: module "eap" returns invalid for request 7
modcall: leaving group authenticate (returns invalid) for request 7
auth: Failed to validate the user.
Login incorrect: [vlan3/<no User-Password attribute>] (from client
ap-test port 263 cli 000c.f135.f1ba)
Delaying request 7 for 1 seconds
Finished request 7
Going to the next request
It is possibile that my problem is this?
rlm_eap_peap: Had sent TLV failure. User was rejcted rejected earlier
in this session.
I tried a lot of thing but I can't find a solution for my problem...
Thanks, bye Antonio
on 15/04/2006 20.03 Alan DeKok said the following:
Bertrand Poulet <[EMAIL PROTECTED]> wrote:
at line 66 of users files , i've got :
bertrand Cisco-AVPair == "ssid=my_ssid", User-Password == "bertrand"
Use := for User-Password.
Alan DeKok.
-
List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
