Hello all,
I am trying to get a basic freeradius 1.0.4 server configured to
authenticate users from the local unix password/group databases on a
FreeBSD 6.1 box. The end result is to get ipsec-tools to do user
authentication for some development and testing. I have pared down my
radius.conf file ( probably too much ) to get rid of the modules I
didn't think I needed.
The error I am getting is as follows ...
rad_recv: Access-Request packet from host 127.0.0.1:51330, id=102, length=71
User-Name = "vpntest"
User-Password = "xxxxxxxxx"
NAS-IP-Address = 10.22.200.1
NAS-Port = 0
NAS-Port-Type = Virtual
Service-Type = Framed-User
Processing the authorize section of radiusd.conf
modcall: entering group authorize for request 0
radius_xlat: '/var/log/radacct//detail'
rlm_detail: %A/%{Client-IP-Address}/detail expands to
/var/log/radacct//detail
modcall[authorize]: module "auth_log" returns ok for request 0
modcall: group authorize returns ok for request 0
auth: No authenticate method (Auth-Type) configuration found for the
request: Rejecting the user
auth: Failed to validate the user.
Delaying request 0 for 1 seconds
Finished request 0
Going to the next request
--- Walking the entire request list ---
Waking up in 1 seconds...
--- Walking the entire request list ---
Waking up in 1 seconds...
--- Walking the entire request list ---
Sending Access-Reject of id 102 to 127.0.0.1:51330
Waking up in 4 seconds...
... I guess I just don't understand how the Auth-Type is selected which
I assume needs to be set to 'unix'? I'm sure its quite obvious by now
that I am not that familiar with configuring radius servers for
authentication. I have attached my radius.conf file in the hope that
some kind sole is willing to educate me in this regard.
Thanks in advance,
-Matthew
##
## radiusd.conf -- FreeRADIUS server configuration file.
##
## http://www.freeradius.org/
## $Id: radiusd.conf.in,v 1.188.2.4 2005/06/11 22:20:40 nbk Exp $
##
# The location of other config files and
# logfiles are declared in this file
#
# Also general configuration for modules can be done
# in this file, it is exported through the API to
# modules that ask for it.
#
# The configuration variables defined here are of the form ${foo}
# They are local to this file, and do not change from request to
# request.
#
# The per-request variables are of the form %{Attribute-Name}, and
# are taken from the values of the attribute in the incoming
# request. See 'doc/variables.txt' for more information.
prefix = /usr/local
exec_prefix = ${prefix}
sysconfdir = ${prefix}/etc
localstatedir = /var
sbindir = ${exec_prefix}/sbin
logdir = /var/log
raddbdir = ${sysconfdir}/raddb
radacctdir = ${logdir}/radacct
# Location of config and logfiles.
confdir = ${raddbdir}
run_dir = ${localstatedir}/run/radiusd
#
# The logging messages for the server are appended to the
# tail of this file.
#
log_file = ${logdir}/radius.log
#
# libdir: Where to find the rlm_* modules.
#
# This should be automatically set at configuration time.
#
# If the server builds and installs, but fails at execution time
# with an 'undefined symbol' error, then you can use the libdir
# directive to work around the problem.
#
# The cause is usually that a library has been installed on your
# system in a place where the dynamic linker CANNOT find it. When
# executing as root (or another user), your personal environment MAY
# be set up to allow the dynamic linker to find the library. When
# executing as a daemon, FreeRADIUS MAY NOT have the same
# personalized configuration.
#
# To work around the problem, find out which library contains that symbol,
# and add the directory containing that library to the end of 'libdir',
# with a colon separating the directory names. NO spaces are allowed.
#
# e.g. libdir = /usr/local/lib:/opt/package/lib
#
# You can also try setting the LD_LIBRARY_PATH environment variable
# in a script which starts the server.
#
# If that does not work, then you can re-configure and re-build the
# server to NOT use shared libraries, via:
#
# ./configure --disable-shared
# make
# make install
#
libdir = ${exec_prefix}/lib
# pidfile: Where to place the PID of the RADIUS server.
#
# The server may be signalled while it's running by using this
# file.
#
# This file is written when ONLY running in daemon mode.
#
# e.g.: kill -HUP `cat /var/run/radiusd/radiusd.pid`
#
pidfile = ${run_dir}/radiusd.pid
# user/group: The name (or #number) of the user/group to run radiusd as.
#
# If these are commented out, the server will run as the user/group
# that started it. In order to change to a different user/group, you
# MUST be root ( or have root privleges ) to start the server.
#
# We STRONGLY recommend that you run the server with as few permissions
# as possible. That is, if you're not using shadow passwords, the
# user and group items below should be set to 'nobody'.
#
# On SCO (ODT 3) use "user = nouser" and "group = nogroup".
#
# NOTE that some kernels refuse to setgid(group) when the value of
# (unsigned)group is above 60000; don't use group nobody on these systems!
#
# On systems with shadow passwords, you might have to set 'group = shadow'
# for the server to be able to read the shadow password file. If you can
# authenticate users while in debug mode, but not in daemon mode, it may be
# that the debugging mode server is running as a user that can read the
# shadow info, and the user listed below can not.
#
#user = nobody
#group = nobody
# max_request_time: The maximum time (in seconds) to handle a request.
#
# Requests which take more time than this to process may be killed, and
# a REJECT message is returned.
#
# WARNING: If you notice that requests take a long time to be handled,
# then this MAY INDICATE a bug in the server, in one of the modules
# used to handle a request, OR in your local configuration.
#
# This problem is most often seen when using an SQL database. If it takes
# more than a second or two to receive an answer from the SQL database,
# then it probably means that you haven't indexed the database. See your
# SQL server documentation for more information.
#
# Useful range of values: 5 to 120
#
max_request_time = 30
# delete_blocked_requests: If the request takes MORE THAN 'max_request_time'
# to be handled, then maybe the server should delete it.
#
# If you're running in threaded, or thread pool mode, this setting
# should probably be 'no'. Setting it to 'yes' when using a threaded
# server MAY cause the server to crash!
#
delete_blocked_requests = no
# cleanup_delay: The time to wait (in seconds) before cleaning up
# a reply which was sent to the NAS.
#
# The RADIUS request is normally cached internally for a short period
# of time, after the reply is sent to the NAS. The reply packet may be
# lost in the network, and the NAS will not see it. The NAS will then
# re-send the request, and the server will respond quickly with the
# cached reply.
#
# If this value is set too low, then duplicate requests from the NAS
# MAY NOT be detected, and will instead be handled as seperate requests.
#
# If this value is set too high, then the server will cache too many
# requests, and some new requests may get blocked. (See 'max_requests'.)
#
# Useful range of values: 2 to 10
#
cleanup_delay = 5
# max_requests: The maximum number of requests which the server keeps
# track of. This should be 256 multiplied by the number of clients.
# e.g. With 4 clients, this number should be 1024.
#
# If this number is too low, then when the server becomes busy,
# it will not respond to any new requests, until the 'cleanup_delay'
# time has passed, and it has removed the old requests.
#
# If this number is set too high, then the server will use a bit more
# memory for no real benefit.
#
# If you aren't sure what it should be set to, it's better to set it
# too high than too low. Setting it to 1000 per client is probably
# the highest it should be.
#
# Useful range of values: 256 to infinity
#
max_requests = 1024
# bind_address: Make the server listen on a particular IP address, and
# send replies out from that address. This directive is most useful
# for machines with multiple IP addresses on one interface.
#
# It can either contain "*", or an IP address, or a fully qualified
# Internet domain name. The default is "*"
#
# As of 1.0, you can also use the "listen" directive. See below for
# more information.
#
bind_address = *
# port: Allows you to bind FreeRADIUS to a specific port.
#
# The default port that most NAS boxes use is 1645, which is historical.
# RFC 2138 defines 1812 to be the new port. Many new servers and
# NAS boxes use 1812, which can create interoperability problems.
#
# The port is defined here to be 0 so that the server will pick up
# the machine's local configuration for the radius port, as defined
# in /etc/services.
#
# If you want to use the default RADIUS port as defined on your server,
# (usually through 'grep radius /etc/services') set this to 0 (zero).
#
# A port given on the command-line via '-p' over-rides this one.
#
# As of 1.0, you can also use the "listen" directive. See below for
# more information.
#
port = 0
#
# By default, the server uses "bind_address" to listen to all IP's
# on a machine, or just one IP. The "port" configuration is used
# to select the authentication port used when listening on those
# addresses.
#
# If you want the server to listen on additional addresses, you can
# use the "listen" section. A sample section (commented out) is included
# below. This "listen" section duplicates the functionality of the
# "bind_address" and "port" configuration entries, but it only listens
# for authentication packets.
#
# If you comment out the "bind_address" and "port" configuration entries,
# then it becomes possible to make the server accept only accounting,
# or authentication packets. Previously, it always listened for both
# types of packets, and it was impossible to make it listen for only
# one type of packet.
#
#listen {
# IP address on which to listen.
# Allowed values are:
# dotted quad (1.2.3.4)
# hostname (radius.example.com)
# wildcard (*)
# ipaddr = *
# Port on which to listen.
# Allowed values are:
# integer port number (1812)
# 0 means "use /etc/services for the proper port"
# port = 0
# Type of packets to listen for.
# Allowed values are:
# auth listen for authentication packets
# acct listen for accounting packets
#
# type = auth
#}
# hostname_lookups: Log the names of clients or just their IP addresses
# e.g., www.freeradius.org (on) or 206.47.27.232 (off).
#
# The default is 'off' because it would be overall better for the net
# if people had to knowingly turn this feature on, since enabling it
# means that each client request will result in AT LEAST one lookup
# request to the nameserver. Enabling hostname_lookups will also
# mean that your server may stop randomly for 30 seconds from time
# to time, if the DNS requests take too long.
#
# Turning hostname lookups off also means that the server won't block
# for 30 seconds, if it sees an IP address which has no name associated
# with it.
#
# allowed values: {no, yes}
#
hostname_lookups = no
# Core dumps are a bad thing. This should only be set to 'yes'
# if you're debugging a problem with the server.
#
# allowed values: {no, yes}
#
allow_core_dumps = no
# Regular expressions
#
# These items are set at configure time. If they're set to "yes",
# then setting them to "no" turns off regular expression support.
#
# If they're set to "no" at configure time, then setting them to "yes"
# WILL NOT WORK. It will give you an error.
#
regular_expressions = yes
extended_expressions = yes
# Log the full User-Name attribute, as it was found in the request.
#
# allowed values: {no, yes}
#
log_stripped_names = no
# Log authentication requests to the log file.
#
# allowed values: {no, yes}
#
log_auth = no
# Log passwords with the authentication requests.
# log_auth_badpass - logs password if it's rejected
# log_auth_goodpass - logs password if it's correct
#
# allowed values: {no, yes}
#
log_auth_badpass = no
log_auth_goodpass = no
# usercollide: Turn "username collision" code on and off. See the
# "doc/duplicate-users" file
#
# WARNING
# !!!!!!! Setting this to "yes" may result in the server behaving
# !!!!!!! strangely. The "username collision" code will ONLY work
# !!!!!!! with clear-text passwords. Even then, it may not do what
# !!!!!!! you want, or what you expect.
# !!!!!!!
# !!!!!!! We STRONGLY RECOMMEND that you do not use this feature,
# !!!!!!! and that you find another way of acheiving the same goal.
# !!!!!!!
# !!!!!!! e,g. module fail-over. See 'doc/configurable_failover'
# WARNING
#
usercollide = no
# lower_user / lower_pass:
# Lower case the username/password "before" or "after"
# attempting to authenticate.
#
# If "before", the server will first modify the request and then try
# to auth the user. If "after", the server will first auth using the
# values provided by the user. If that fails it will reprocess the
# request after modifying it as you specify below.
#
# This is as close as we can get to case insensitivity. It is the
# admin's job to ensure that the username on the auth db side is
# *also* lowercase to make this work
#
# Default is 'no' (don't lowercase values)
# Valid values = "before" / "after" / "no"
#
lower_user = no
lower_pass = no
# nospace_user / nospace_pass:
#
# Some users like to enter spaces in their username or password
# incorrectly. To save yourself the tech support call, you can
# eliminate those spaces here:
#
# Default is 'no' (don't remove spaces)
# Valid values = "before" / "after" / "no" (explanation above)
#
nospace_user = no
nospace_pass = no
# The program to execute to do concurrency checks.
checkrad = ${sbindir}/checkrad
# SECURITY CONFIGURATION
#
# There may be multiple methods of attacking on the server. This
# section holds the configuration items which minimize the impact
# of those attacks
#
security {
#
# max_attributes: The maximum number of attributes
# permitted in a RADIUS packet. Packets which have MORE
# than this number of attributes in them will be dropped.
#
# If this number is set too low, then no RADIUS packets
# will be accepted.
#
# If this number is set too high, then an attacker may be
# able to send a small number of packets which will cause
# the server to use all available memory on the machine.
#
# Setting this number to 0 means "allow any number of attributes"
max_attributes = 200
#
# delayed_reject: When sending an Access-Reject, it can be
# delayed for a few seconds. This may help slow down a DoS
# attack. It also helps to slow down people trying to brute-force
# crack a users password.
#
# Setting this number to 0 means "send rejects immediately"
#
# If this number is set higher than 'cleanup_delay', then the
# rejects will be sent at 'cleanup_delay' time, when the request
# is deleted from the internal cache of requests.
#
# Useful ranges: 1 to 5
reject_delay = 1
#
# status_server: Whether or not the server will respond
# to Status-Server requests.
#
# Normally this should be set to "no", because they're useless.
# See: http://www.freeradius.org/rfc/rfc2865.html#Keep-Alives
#
# However, certain NAS boxes may require them.
#
# When sent a Status-Server message, the server responds with
# an Access-Accept packet, containing a Reply-Message attribute,
# which is a string describing how long the server has been
# running.
#
status_server = no
}
# PROXY CONFIGURATION
#
# proxy_requests: Turns proxying of RADIUS requests on or off.
#
# The server has proxying turned on by default. If your system is NOT
# set up to proxy requests to another server, then you can turn proxying
# off here. This will save a small amount of resources on the server.
#
# If you have proxying turned off, and your configuration files say
# to proxy a request, then an error message will be logged.
#
# To disable proxying, change the "yes" to "no", and comment the
# $INCLUDE line.
#
# allowed values: {no, yes}
#
proxy_requests = no
# CLIENTS CONFIGURATION
#
# Client configuration is defined in "clients.conf".
#
# The 'clients.conf' file contains all of the information from the old
# 'clients' and 'naslist' configuration files. We recommend that you
# do NOT use 'client's or 'naslist', although they are still
# supported.
#
# Anything listed in 'clients.conf' will take precedence over the
# information from the old-style configuration files.
#
$INCLUDE ${confdir}/clients.conf
# SNMP CONFIGURATION
#
# Snmp configuration is only valid if SNMP support was enabled
# at compile time.
#
# To enable SNMP querying of the server, set the value of the
# 'snmp' attribute to 'yes'
#
snmp = no
$INCLUDE ${confdir}/snmp.conf
# THREAD POOL CONFIGURATION
#
# The thread pool is a long-lived group of threads which
# take turns (round-robin) handling any incoming requests.
#
# You probably want to have a few spare threads around,
# so that high-load situations can be handled immediately. If you
# don't have any spare threads, then the request handling will
# be delayed while a new thread is created, and added to the pool.
#
# You probably don't want too many spare threads around,
# otherwise they'll be sitting there taking up resources, and
# not doing anything productive.
#
# The numbers given below should be adequate for most situations.
#
thread pool {
# Number of servers to start initially --- should be a reasonable
# ballpark figure.
start_servers = 5
# Limit on the total number of servers running.
#
# If this limit is ever reached, clients will be LOCKED OUT, so it
# should NOT BE SET TOO LOW. It is intended mainly as a brake to
# keep a runaway server from taking the system with it as it spirals
# down...
#
# You may find that the server is regularly reaching the
# 'max_servers' number of threads, and that increasing
# 'max_servers' doesn't seem to make much difference.
#
# If this is the case, then the problem is MOST LIKELY that
# your back-end databases are taking too long to respond, and
# are preventing the server from responding in a timely manner.
#
# The solution is NOT do keep increasing the 'max_servers'
# value, but instead to fix the underlying cause of the
# problem: slow database, or 'hostname_lookups=yes'.
#
# For more information, see 'max_request_time', above.
#
max_servers = 32
# Server-pool size regulation. Rather than making you guess
# how many servers you need, FreeRADIUS dynamically adapts to
# the load it sees, that is, it tries to maintain enough
# servers to handle the current load, plus a few spare
# servers to handle transient load spikes.
#
# It does this by periodically checking how many servers are
# waiting for a request. If there are fewer than
# min_spare_servers, it creates a new spare. If there are
# more than max_spare_servers, some of the spares die off.
# The default values are probably OK for most sites.
#
min_spare_servers = 3
max_spare_servers = 10
# There may be memory leaks or resource allocation problems with
# the server. If so, set this value to 300 or so, so that the
# resources will be cleaned up periodically.
#
# This should only be necessary if there are serious bugs in the
# server which have not yet been fixed.
#
# '0' is a special value meaning 'infinity', or 'the servers never
# exit'
max_requests_per_server = 0
}
# MODULE CONFIGURATION
#
# The names and configuration of each module is located in this section.
#
# After the modules are defined here, they may be referred to by name,
# in other sections of this configuration file.
#
modules {
#
# Each module has a configuration as follows:
#
# name [ instance ] {
# config_item = value
# ...
# }
#
# The 'name' is used to load the 'rlm_name' library
# which implements the functionality of the module.
#
# The 'instance' is optional. To have two different instances
# of a module, it first must be referred to by 'name'.
# The different copies of the module are then created by
# inventing two 'instance' names, e.g. 'instance1' and 'instance2'
#
# The instance names can then be used in later configuration
# INSTEAD of the original 'name'. See the 'radutmp' configuration
# below for an example.
#
# Unix /etc/passwd style authentication
#
unix {
#
# Cache /etc/passwd, /etc/shadow, and /etc/group
#
# The default is to NOT cache them.
#
# For FreeBSD and NetBSD, you do NOT want to enable
# the cache, as it's password lookups are done via a
# database, so set this value to 'no'.
#
# Some systems (e.g. RedHat Linux with pam_pwbd) can
# take *seconds* to check a password, when th passwd
# file containing 1000's of entries. For those systems,
# you should set the cache value to 'yes', and set
# the locations of the 'passwd', 'shadow', and 'group'
# files, below.
#
# allowed values: {no, yes}
cache = no
# Reload the cache every 600 seconds (10mins). 0 to disable.
cache_reload = 600
}
# Write a detailed log of all accounting records received.
#
detail {
# Note that we do NOT use NAS-IP-Address here, as
# that attribute MAY BE from the originating NAS, and
# NOT from the proxy which actually sent us the
# request. The Client-IP-Address attribute is ALWAYS
# the address of the client which sent us the
# request.
#
# The following line creates a new detail file for
# every radius client (by IP address or hostname).
# In addition, a new detail file is created every
# day, so that the detail file doesn't have to go
# through a 'log rotation'
#
# If your detail files are large, you may also want
# to add a ':%H' (see doc/variables.txt) to the end
# of it, to create a new detail file every hour, e.g.:
#
# ..../detail-%Y%m%d:%H
#
# This will create a new detail file for every hour.
#
detailfile = ${radacctdir}/%{Client-IP-Address}/detail-%Y%m%d
#
# The Unix-style permissions on the 'detail' file.
#
# The detail file often contains secret or private
# information about users. So by keeping the file
# permissions restrictive, we can prevent unwanted
# people from seeing that information.
detailperm = 0600
}
#
# Many people want to log authentication requests.
# Rather than modifying the server core to print out more
# messages, we can use a different instance of the 'detail'
# module, to log the authentication requests to a file.
#
# You will also need to un-comment the 'auth_log' line
# in the 'authorize' section, below.
#
detail auth_log {
detailfile =
${radacctdir}/%{Client-IP-Address}/auth-detail-%Y%m%d
#
# This MUST be 0600, otherwise anyone can read
# the users passwords!
detailperm = 0600
}
#
# This module logs authentication reply packets sent
# to a NAS. Both Access-Accept and Access-Reject packets
# are logged.
#
# You will also need to un-comment the 'reply_log' line
# in the 'post-auth' section, below.
#
detail reply_log {
detailfile =
${radacctdir}/%{Client-IP-Address}/reply-detail-%Y%m%d
#
# This MUST be 0600, otherwise anyone can read
# the users passwords!
detailperm = 0600
}
#
# This module logs packets proxied to a home server.
#
# You will also need to un-comment the 'pre_proxy_log' line
# in the 'pre-proxy' section, below.
#
# detail pre_proxy_log {
# detailfile =
${radacctdir}/%{Client-IP-Address}/pre-proxy-detail-%Y%m%d
#
# This MUST be 0600, otherwise anyone can read
# the users passwords!
# detailperm = 0600
# }
#
# This module logs response packets from a home server.
#
# You will also need to un-comment the 'post_proxy_log' line
# in the 'post-proxy' section, below.
#
# detail post_proxy_log {
# detailfile =
${radacctdir}/%{Client-IP-Address}/post-proxy-detail-%Y%m%d
#
# This MUST be 0600, otherwise anyone can read
# the users passwords!
# detailperm = 0600
# }
# Create a unique accounting session Id. Many NASes re-use or
# repeat values for Acct-Session-Id, causing no end of
# confusion.
#
# This module will add a (probably) unique session id
# to an accounting packet based on the attributes listed
# below found in the packet. See doc/rlm_acct_unique for
# more information.
#
acct_unique {
key = "User-Name, Acct-Session-Id, NAS-IP-Address,
Client-IP-Address, NAS-Port"
}
# Write a 'utmp' style file, of which users are currently
# logged in, and where they've logged in from.
#
# This file is used mainly for Simultaneous-Use checking,
# and also 'radwho', to see who's currently logged in.
#
radutmp {
# Where the file is stored. It's not a log file,
# so it doesn't need rotating.
#
filename = ${logdir}/radutmp
# The field in the packet to key on for the
# 'user' name, If you have other fields which you want
# to use to key on to control Simultaneous-Use,
# then you can use them here.
#
# Note, however, that the size of the field in the
# 'utmp' data structure is small, around 32
# characters, so that will limit the possible choices
# of keys.
#
# You may want instead: %{Stripped-User-Name:-%{User-Name}}
username = %{User-Name}
# Whether or not we want to treat "user" the same
# as "USER", or "User". Some systems have problems
# with case sensitivity, so this should be set to
# 'no' to enable the comparisons of the key attribute
# to be case insensitive.
#
case_sensitive = yes
# Accounting information may be lost, so the user MAY
# have logged off of the NAS, but we haven't noticed.
# If so, we can verify this information with the NAS,
#
# If we want to believe the 'utmp' file, then this
# configuration entry can be set to 'no'.
#
check_with_nas = yes
# Set the file permissions, as the contents of this file
# are usually private.
perm = 0600
callerid = "yes"
}
# "Safe" radutmp - does not contain caller ID, so it can be
# world-readable, and radwho can work for normal users, without
# exposing any information that isn't already exposed by who(1).
#
# This is another 'instance' of the radutmp module, but it is given
# then name "sradutmp" to identify it later in the "accounting"
# section.
radutmp sradutmp {
filename = ${logdir}/sradutmp
perm = 0644
callerid = "no"
}
# attr_filter - filters the attributes received in replies from
# proxied servers, to make sure we send back to our RADIUS client
# only allowed attributes.
attr_filter {
attrsfile = ${confdir}/attrs
}
# counter module:
# This module takes an attribute (count-attribute).
# It also takes a key, and creates a counter for each unique
# key. The count is incremented when accounting packets are
# received by the server. The value of the increment depends
# on the attribute type.
# If the attribute is Acct-Session-Time or of an integer type we add
the
# value of the attribute. If it is anything else we increase the
# counter by one.
#
# The 'reset' parameter defines when the counters are all reset to
# zero. It can be hourly, daily, weekly, monthly or never.
#
# hourly: Reset on 00:00 of every hour
# daily: Reset on 00:00:00 every day
# weekly: Reset on 00:00:00 on sunday
# monthly: Reset on 00:00:00 of the first day of each month
#
# It can also be user defined. It should be of the form:
# num[hdwm] where:
# h: hours, d: days, w: weeks, m: months
# If the letter is ommited days will be assumed. In example:
# reset = 10h (reset every 10 hours)
# reset = 12 (reset every 12 days)
#
#
# The check-name attribute defines an attribute which will be
# registered by the counter module and can be used to set the
# maximum allowed value for the counter after which the user
# is rejected.
# Something like:
#
# DEFAULT Max-Daily-Session := 36000
# Fall-Through = 1
#
# You should add the counter module in the instantiate
# section so that it registers check-name before the files
# module reads the users file.
#
# If check-name is set and the user is to be rejected then we
# send back a Reply-Message and we log a Failure-Message in
# the radius.log
# If the count attribute is Acct-Session-Time then on each login
# we send back the remaining online time as a Session-Timeout attribute
#
# The counter-name can also be used instead of using the check-name
# like below:
#
# DEFAULT Daily-Session-Time > 3600, Auth-Type = Reject
# Reply-Message = "You've used up more than one hour today"
#
# The allowed-servicetype attribute can be used to only take
# into account specific sessions. For example if a user first
# logs in through a login menu and then selects ppp there will
# be two sessions. One for Login-User and one for Framed-User
# service type. We only need to take into account the second one.
#
# The module should be added in the instantiate, authorize and
# accounting sections. Make sure that in the authorize
# section it comes after any module which sets the
# 'check-name' attribute.
#
counter daily {
filename = ${raddbdir}/db.daily
key = User-Name
count-attribute = Acct-Session-Time
reset = daily
counter-name = Daily-Session-Time
check-name = Max-Daily-Session
allowed-servicetype = Framed-User
cache-size = 5000
}
# The "always" module is here for debugging purposes. Each
# instance simply returns the same result, always, without
# doing anything.
always fail {
rcode = fail
}
always reject {
rcode = reject
}
always ok {
rcode = ok
simulcount = 0
mpp = no
}
#
# The 'expression' module currently has no configuration.
#
# This module is useful only for 'xlat'. To use it,
# put 'exec' into the 'instantiate' section. You can then
# do dynamic translation of attributes like:
#
# Attribute-Name = `%{expr:2 + 3 + %{exec: uid -u}}`
#
# The value of the attribute will be replaced with the output
# of the program which is executed. Due to RADIUS protocol
# limitations, any output over 253 bytes will be ignored.
expr {
}
#
# The 'digest' module currently has no configuration.
#
# "Digest" authentication against a Cisco SIP server.
# See 'doc/rfc/draft-sterman-aaa-sip-00.txt' for details
# on performing digest authentication for Cisco SIP servers.
#
digest {
}
# Do server side ip pool management. Should be added in post-auth and
# accounting sections.
#
# The module also requires the existance of the Pool-Name
# attribute. That way the administrator can add the Pool-Name
# attribute in the user profiles and use different pools
# for different users. The Pool-Name attribute is a *check* item not
# a reply item.
#
# Example:
# radiusd.conf: ippool students { [...] }
# users file : DEFAULT Group == students, Pool-Name := "students"
#
# ********* IF YOU CHANGE THE RANGE PARAMETERS YOU MUST *********
# ********* THEN ERASE THE DB FILES *********
#
ippool main_pool {
# range-start,range-stop: The start and end ip
# addresses for the ip pool
range-start = 192.168.1.1
range-stop = 192.168.3.254
# netmask: The network mask used for the ip's
netmask = 255.255.255.0
# cache-size: The gdbm cache size for the db
# files. Should be equal to the number of ip's
# available in the ip pool
cache-size = 800
# session-db: The main db file used to allocate ip's to clients
session-db = ${raddbdir}/db.ippool
# ip-index: Helper db index file used in multilink
ip-index = ${raddbdir}/db.ipindex
# override: Will this ippool override a Framed-IP-Address
already set
override = no
# maximum-timeout: If not zero specifies the maximum time in
seconds an
# entry may be active. Default: 0
maximum-timeout = 0
}
# ANSI X9.9 token support. Not included by default.
# $INCLUDE ${confdir}/x99.conf
}
# Instantiation
#
# This section orders the loading of the modules. Modules
# listed here will get loaded BEFORE the later sections like
# authorize, authenticate, etc. get examined.
#
# This section is not strictly needed. When a section like
# authorize refers to a module, it's automatically loaded and
# initialized. However, some modules may not be listed in any
# of the following sections, so they can be listed here.
#
# Also, listing modules here ensures that you have control over
# the order in which they are initalized. If one module needs
# something defined by another module, you can list them in order
# here, and ensure that the configuration will be OK.
#
instantiate {
#
# The expression module doesn't do authorization,
# authentication, or accounting. It only does dynamic
# translation, of the form:
#
# Session-Timeout = `%{expr:2 + 3}`
#
# So the module needs to be instantiated, but CANNOT be
# listed in any other section. See 'doc/rlm_expr' for
# more information.
#
expr
}
# Authorization. First preprocess (hints and huntgroups files),
# then realms, and finally look in the "users" file.
#
# The order of the realm modules will determine the order that
# we try to find a matching realm.
#
# Make *sure* that 'preprocess' comes before any realm if you
# need to setup hints for the remote radius server
authorize {
#
# If you want to have a log of authentication requests,
# un-comment the following line, and the 'detail auth_log'
# section, above.
auth_log
}
# Authentication.
#
#
# This section lists which modules are available for authentication.
# Note that it does NOT mean 'try each module in order'. It means
# that a module from the 'authorize' section adds a configuration
# attribute 'Auth-Type := FOO'. That authentication type is then
# used to pick the apropriate module from the list below.
#
# In general, you SHOULD NOT set the Auth-Type attribute. The server
# will figure it out on its own, and will do the right thing. The
# most common side effect of erroneously setting the Auth-Type
# attribute is that one authentication method will work, but the
# others will not.
#
# The common reasons to set the Auth-Type attribute by hand
# is to either forcibly reject the user, or forcibly accept him.
#
authenticate {
#
# See 'man getpwent' for information on how the 'unix'
# module checks the users password. Note that packets
# containing CHAP-Password attributes CANNOT be authenticated
# against /etc/passwd! See the FAQ for details.
#
unix
}
#
# Pre-accounting. Decide which accounting type to use.
#
preacct {
#
# Ensure that we have a semi-unique identifier for every
# request, and many NAS boxes are broken.
acct_unique
}
#
# Accounting. Log the accounting data.
#
accounting {
#
# Create a 'detail'ed log of the packets.
# Note that accounting requests which are proxied
# are also logged in the detail file.
detail
#
# For Simultaneous-Use tracking.
#
# Due to packet losses in the network, the data here
# may be incorrect. There is little we can do about it.
radutmp
}
# Session database, used for checking Simultaneous-Use. Either the radutmp
# or rlm_sql module can handle this.
# The rlm_sql module is *much* faster
session {
radutmp
}
-
List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
