Thank you Kevin, but it didn't work now my entire
users file is:
sebas Crypt-Password := "(!lGOOlHaBWoQ"
Service-Type = Administrative-User,
Cisco-AVPair = "shell:priv-lvl=15"
and then the debug was:
rad_recv: Access-Request packet from host 10.12.4.2:1645, id=103,
length=75
NAS-IP-Address = 10.12.4.2
NAS-Port = 1
NAS-Port-Type = Virtual
User-Name = "sebas"
Calling-Station-Id = "10.11.1.25"
User-Password = "hello"
Processing the authorize section of radiusd.conf
modcall: entering group authorize for request 0
modcall[authorize]: module "preprocess" returns ok for request 0
users: Matched entry sebas at line 1
modcall[authorize]: module "files" returns ok for request 0
modcall: leaving group authorize (returns ok) for request 0
auth: type Crypt
auth: Failed to validate the user.
Delaying request 0 for 1 seconds
Finished request 0
Going to the next request
--- Walking the entire request list ---
Waking up in 1 seconds...
--- Walking the entire request list ---
Waking up in 1 seconds...
--- Walking the entire request list ---
Sending Access-Reject of id 103 to 10.12.4.2 port 1645
Waking up in 4 seconds...
--- Walking the entire request list ---
Cleaning up request 0 ID 103 with timestamp 4626942f
Nothing to do. Sleeping until we see a request.
Another idea??
Thanks a lot, any way.
Kevin Bonner wrote:
On Wednesday 18 April 2007 16:39:27 Sebastian Firpo wrote:
Hi, I migrated a freeradius server from version 0.6 to 1.5. I'm using a
users file for authorize.
Wow, that's quite a leap. I assume from 0.6 to 1.1.5?
The server don't authorize and when a do a debug (radiusd -X) I saw the
User-password in clear text. If I modify the User-password in the users
file by the clear text one it works.
Here are the debug and an entry of the users file:
Listening on authentication *:1812
Listening on accounting *:1813
Ready to process requests.
rad_recv: Access-Request packet from host 10.12.4.2:1645, id=91, length=75
NAS-IP-Address = 10.12.4.2
NAS-Port = 1
NAS-Port-Type = Virtual
User-Name = "sebas"
Calling-Station-Id = "10.11.1.25"
User-Password = "hello"
Processing the authorize section of radiusd.conf
modcall: entering group authorize for request 0
modcall[authorize]: module "preprocess" returns ok for request 0
users: Matched entry sebas at line 50
modcall[authorize]: module "files" returns ok for request 0
modcall: leaving group authorize (returns ok) for request 0
rad_check_password: Found Auth-Type Local
auth: type Local
auth: user supplied User-Password does NOT match local User-Password
auth: Failed to validate the user.
Delaying request 0 for 1 seconds
users file
sebas Auth-Type := Local, Crypt-Password == "(!lGOOlHaBWoQ"
Service-Type = Administrative-User,
Cisco-AVPair = "shell:priv-lvl=15"
Thanks very much!!
Don't set Auth-Type, the server will figure it out. The operator for
Crypt-Password should be changed to := as well.
Kevin Bonner
-
List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
|
-
List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
