Hello Tevfik, Run radius in debug mode (radius -X) and then try to authenticate the user. You should have enough information in the debug to figure out the problem.
If you still can't figure it out paste your debug output here. You may also want to mention what version of freeradius you're using. Adrian -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Tevfik Ceydeliler Sent: Tuesday, January 12, 2010 2:15 AM To: [email protected] Subject: My Static IP Client conf. not work Hi Adrian, I change the operator for Framed IP Address and Netmask. But nothing changed. Client get Access-Accept but no IP address assigned. I check it with "ipconfig" Regards... Tevfik Ceydeliler -----Original Message----- From: freeradius-users-bounces+tevfik.ceydeliler=astron.yasar.com...@lists.freeradius.org [mailto:freeradius-users-bounces+tevfik.ceydeliler=astron.yasar.com...@lists.freeradius.org] On Behalf Of [email protected] Sent: Monday, January 11, 2010 6:59 PM To: [email protected] Subject: Freeradius-Users Digest, Vol 57, Issue 31 Send Freeradius-Users mailing list submissions to [email protected] To subscribe or unsubscribe via the World Wide Web, visit http://lists.freeradius.org/mailman/listinfo/freeradius-users or, via email, send a message with subject or body 'help' to [email protected] You can reach the person managing the list at [email protected] When replying, please edit your Subject line so it is more specific than "Re: Contents of Freeradius-Users digest..." Today's Topics: 1. RE: My Static IP Client conf. not work (Adrian Boros) 2. Re: rlm_sqlippool required? (John Dennis) 3. NT/LM password from LDAP (PAP works, MSCHAP doesn't). (Lech Karol Paw?aszek) ---------------------------------------------------------------------- Message: 1 Date: Mon, 11 Jan 2010 09:38:18 -0500 From: "Adrian Boros" <[email protected]> Subject: RE: My Static IP Client conf. not work To: "'FreeRadius users mailing list'" <[email protected]> Message-ID: <0fc901ca92cb$b789fad0$269df0...@ca> Content-Type: text/plain; charset="us-ascii" Hello Tevfik, Try changing the operator from == to := when assigning the Framed IP and Framed Netmask. I would also recommend it for others but you're better off reading the following link which should give you an understanding of the operators in use: http://wiki.freeradius.org/Operators Best regards, Adrian Boros -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Tevfik Ceydeliler Sent: Monday, January 11, 2010 4:55 AM To: [email protected] Subject: My Static IP Client conf. not work Hi, I have a client, when I put this client into an IP pool everything is ok. But when I move him for framed-Ip (static IP),he can't get that IP address. Note: I use a secovid as realm and NAS is Telecom Operator (For APN) I dont know what i should check. Can you help me to start? ################################################################# Here is the user configuration: FOR POOL --> tevfikceydeliler Service-Type == Framed-User,Packet-Type==Access-Request, Proxy-To-Realm := 10.1.1.51, Pool-Name := BirmasGPRS For Static IP --> tevfikceydeliler Packet-Type==Access-Request, Proxy-To-Realm := 10.1.1.51, Framed-IP-Address == 172.30.65.90, Framed-IP-Netmask == 255.255.255, Framed-MTU = 1500, Framed-Routing = None, Framed-Protocol = PPP, Service-Type = Framed, Fall-Through = Yes AND DEFAULTS --> DEFAULT Framed-Protocol == PPP Framed-Protocol = PPP, Framed-Compression = Van-Jacobson-TCP-IP DEFAULT Hint == "CSLIP" Framed-Protocol = SLIP, Framed-Compression = Van-Jacobson-TCP-IP DEFAULT Hint == "SLIP" Framed-Protocol = SLIP DEFAULT Auth-Type := Accept ################################################### Bu elektronik postada bulunan tum fikir ve gorusler ve ekindeki dosyalar sadece adres sahip/sahiplerine ait olup, Yasar Toplulugu Sirketleri bu mesajin icerigi ile ilgili olarak hic bir hukuksal sorumlulugu kabul etmez. Eger gonderilmesi dusunulen kisi veya kurulus degilseniz, lutfen gonderen kisiyi derhal haberdar ediniz ve mesaji sisteminizden siliniz.The information contained in this e-mail and any files transmitted with it are intended solely for the use of the individual or entity to whom they are addressed and Yasar Group Companies do not accept legal responsibility for the contents. If you are not the intended recipient, please immediately notify the sender and delete it from your system. - List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html - List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
