Hi Alan, > Read doc/Simultaneous-Use. It's a how-to, and most questions are > answered there.
Thank you.. I will re-read the Simultaneous-Use Doc again.. I may have to start from a simple configuration, before trying to integrate that with e-Directory. > Ugh. Upgrade to 2.1.10. I'll upgrade to 2.1.10 prior to trying again. > Those look like MAC addresses, perhaps. And that doesn't matter, if > you're trying to do Simultaneous-Use for use "ziggy". Those are not MAC addresses.. They are randomly generated numbers? Why? don't know.. But it doesn't matter I guess. Just makes it hard for me to understand the debug log, since I'm new at it. > > Do you get Accounting-Request packets for user "ziggy"? If not, then > Simultaneous-Use will be hard to do. I looked at the debug log again using the http://networkradius.com/freeradius.html debugging output URL (wish I found it sooner). I see Access-Request packets with "Ziggy" from Packets 3-12 for the authentication portion. The next time I see anything with Username = "Ziggy" is the Accounting-Request packet when I disconnect from the SSID as indicated in the Acct-Status-Type = Stop. In this packet, the calling-station-ID becomes 0.0.0.0. though.. Is that how it is suppose to look? Since it should be "00-22-fa-a1-ba-e8" ? rad_recv: Accounting-Request packet from host 10.32.156.5 port 32768, id=111, length=188 User-Name = "ziggy" NAS-Port = 29 NAS-IP-Address = 10.32.156.5 NAS-Identifier = "CW32CE0A" Airespace-Wlan-Id = 3 Acct-Session-Id = "4defbab6/00:22:fa:a1:ba:e8/12404" Acct-Authentic = RADIUS Tunnel-Type:0 = VLAN Tunnel-Medium-Type:0 = IEEE-802 Tunnel-Private-Group-Id:0 = "342" Acct-Status-Type = Stop Acct-Input-Octets = 68833 Acct-Output-Octets = 9551 Acct-Input-Packets = 559 Acct-Output-Packets = 47 Acct-Terminate-Cause = User-Request Acct-Session-Time = 117 Acct-Delay-Time = 0 Calling-Station-Id = "0.0.0.0" Called-Station-Id = "10.32.156.5" On Thu, Jun 9, 2011 at 8:19 PM, Alan DeKok <[email protected]> wrote: > Ziggy Bopster wrote: >> I am want to enable Simultaneous-Use for our users. I have been stuck >> for many many days trying to figure this out, any help is greatly >> appreciated. This is my first time posting, so sorry if my netiquette >> is not correct > > Read doc/Simultaneous-Use. It's a how-to, and most questions are > answered there. > >> I. Configuration of System: >> FreeRADIUS Version 2.1.1, built on May 9 2010 at 12:09:29 > > Ugh. Upgrade to 2.1.10. > >> III. Problem: >> In looking at the debug logs, randomly generated UserName >> Accounting-Request packets are being sent from the NAS to the >> FreeRADIUS, before and after the successful authentication of the >> UserName (ziggy) using the EAP-PEAP-MSCHAPV2 protocol (during which >> time the correct UserName is sent by NAS). > > Those look like MAC addresses, perhaps. And that doesn't matter, if > you're trying to do Simultaneous-Use for use "ziggy". > > Do you get Accounting-Request packets for user "ziggy"? If not, then > Simultaneous-Use will be hard to do. > > Alan DeKok. > - > List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html > - List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
