Q.931 and Q.921 are protocols for Euro ISDN. So this is the right protocol. See here: http://www.voip-info.org/wiki/view/EuroISDN
Best regards Peter Niall Crosby schrieb: > Sorry, my mistake. > > I was asked by telco to specifically use Euro dialect, will using Q931 > cause any issues? > > tnks > > 2009/7/31 Peter P GMX <[email protected]>: > >>> I was asked by telco to specifically use telco, will using Q931 cause >>> any issues for me? >>> >> Sorry, I do not not understand that question. >> >> Best regards >> Peter >> >> Niall Crosby schrieb: >> >>> Thanks for help. >>> >>> Got my alarms sorted - telco had problem there. >>> >>> As for my Freeswitch problem, chaning to Q931 clears the error message. >>> >>> I was asked by telco to specifically use telco, will using Q931 cause >>> any issues for me? >>> >>> Thanks again, >>> Niall. >>> >>> 2009/7/31 Peter P GMX <[email protected]>: >>> >>> >>>> Firstly I would try get get rid of the sangoma errors. There are 2 errors: >>>> >>>> Short Circuit: ON >>>> Loss of Signal: ON >>>> >>>> So either the card is not configured correctly or there is a cabling >>>> problem. What is your wanpipe1.conf? >>>> >>>> Second, if euro doesn't work, try Q931. >>>> I had success with that some time ago. >>>> >>>> Best regards >>>> Peter >>>> >>>> Niall Crosby schrieb: >>>> >>>> >>>>> Hi, >>>>> >>>>> This might be Sangoma config issue, so apologies in advance for >>>>> posting it here if it is. I am waiting for Sangoma helpdesk to get >>>>> back to me! >>>>> >>>>> But I have a Sangoma a101 and trying to get it working with >>>>> Freeswitch. Have E1 line coming from telco and everything set up >>>>> correctly (to my best efforts), however when Freeswitch starts, it >>>>> says: >>>>> >>>>> 2009-07-30 15:17:15.446569 [ERR] mod_openzap.c:1953 Error starting >>>>> OpenZAP span 1 mode: user dialect: euro error: >>>>> >>>>> Also I'm getting the following Sangoma alarms: >>>>> >>>>> ***** w1g1: E1 Alarms (Framer) ***** >>>>> >>>>> ALOS: OFF | LOS: ON >>>>> RED: ON | AIS: OFF >>>>> OOF: ON | RAI: OFF >>>>> >>>>> ***** w1g1: E1 Alarms (LIU) ***** >>>>> >>>>> Short Circuit: ON >>>>> Open Circuit: OFF >>>>> Loss of Signal: ON >>>>> >>>>> >>>>> Can someone tell me where I should be focusing my attention - on the >>>>> Sangoma config or the Freeswitch config? >>>>> >>>>> Also what state should the Sangoma alarms be in when Freeswitch is NOT >>>>> running? Should they all clear? >>>>> >>>>> Thanks in advance, >>>>> Niall. >>>>> >>>>> >>>>> >>>>> >>>>> >>>> _______________________________________________ >>>> FreeSWITCH-users mailing list >>>> [email protected] >>>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users >>>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users >>>> http://www.freeswitch.org >>>> >>>> >>>> >>> >>> >>> >> _______________________________________________ >> FreeSWITCH-users mailing list >> [email protected] >> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users >> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users >> http://www.freeswitch.org >> >> > > > > _______________________________________________ FreeSWITCH-users mailing list [email protected] http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
