Upon the advice of Carlo, I updated the machine to Ganglia 3.0.7-1 with RRDtool rrdtool-1.2.30-1.rh9.rf (the furthest I could take FC5 without horrible dependency chasing). No dice. The CGI page renders correctly for about 1 minute after gmetad stop+start. Then blank page plus "Root epilog" error again.
Regards, Jeff Orr Attributor Corporation Jeff Orr wrote: > Carlo Marcelo Arenas Belon wrote: > >> On Wed, May 06, 2009 at 03:38:34PM -0700, Jeff Orr wrote: >> >> >>> We were using 3.0.4.fc5, so I tried updating to 3.1.2 to see if it fixes >>> the problem. >>> >>> >> this was reported before as a bug in 3.0 which magically went away >> somewhere in the last versions of 3.0 (it might had been because of using >> newer versions of rrdtool as well). >> >> http://bugzilla.ganglia.info/cgi-bin/bugzilla/show_bug.cgi?id=42 >> >> I'd suggest you upgrade to 3.0.7 compiled against a newer version of >> rrdtool to see if the problem goes away as well for you and if not we >> might need to reopen that bug and do more investigation on the source of it >> >> in any case you want to upgrade your gmetad, since it has a vulnerability >> as explained in : >> >> http://bugzilla.ganglia.info/cgi-bin/bugzilla/show_bug.cgi?id=223 >> >> so don't forget to also apply the following patch on top of it : >> >> http://bugzilla.ganglia.info/cgi-bin/bugzilla/attachment.cgi?id=189 >> >> > So, should I patch 3.0.7 and upgrade, or is the upgrade to 3.0.7 sufficient? > > I'll have to compile from source, I think. FC5's end-of-life as far as > updates go. O why can't we move to CentOS? :-( > >>> Now in addition, we are getting these messages on gmond startup >>> >>> >> 3.0 and 3.1 are not compatible at the network/configuration layer and so >> you can't upgrade gmond to 3.1 if you are still using 3.0 in the same cluster >> and if you update all the gmond in a cluster to 3.1 you have to use a new >> configuration as described in the release notes. >> >> since gmond wasn't your problem here, I'd suggest you better rollback this >> update for now, and focus in the gmetad problem. >> >> Carlo >> >> > It was my understanding that 3.1.x and 3.0.x could communicate, i.e. a > 3.0.x cluster could talk to a master running 3.1.x. I distinctly > remember it on the main page for configuring 3.1. Oh well... > > I'll try 3.0.7 with new RRDtool and see how it goes. > > Regards, > Jeff Orr > Attributor Corporation > > > ------------------------------------------------------------------------------ > The NEW KODAK i700 Series Scanners deliver under ANY circumstances! Your > production scanning environment may not be a perfect world - but thanks to > Kodak, there's a perfect scanner to get the job done! With the NEW KODAK i700 > Series Scanner you'll get full speed at 300 dpi even with all image > processing features enabled. http://p.sf.net/sfu/kodak-com > _______________________________________________ > Ganglia-general mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/ganglia-general > ------------------------------------------------------------------------------ The NEW KODAK i700 Series Scanners deliver under ANY circumstances! Your production scanning environment may not be a perfect world - but thanks to Kodak, there's a perfect scanner to get the job done! With the NEW KODAK i700 Series Scanner you'll get full speed at 300 dpi even with all image processing features enabled. http://p.sf.net/sfu/kodak-com _______________________________________________ Ganglia-general mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/ganglia-general
