Hi, The stdout is not enough I am afraid to understand what went wrong. Could you provide the content of the m5out/system.workload.dmesg file ?
Kind Regards Giacomo > -----Original Message----- > From: Csq via gem5-dev <[email protected]> > Sent: 25 March 2021 03:40 > To: [email protected] > Cc: [email protected] > Subject: [gem5-dev] gem5:stopping fetching and kernel panic > > **************************************************** > The contents of the dts file are as follows: > **************************************************** > /dts-v1/; > > /memreserve/ 0x80000000 0x00010000; > > /include/ CONF_PLATFORM > > /* Assign a unique ID for pre-defined configurations. The selected > * configuration is picked up from CONF_CPUS */ // 2 big and 2 little cpus > #define _2_2 1 // 2 big and 4 little cpus #define _2_4 2 > > #define CPU(n,id) \ > CPU ## n: cpu@ ## id { \ > device_type = "cpu"; \ > compatible = "gem5,armv8", "arm,armv8"; \ > reg = < ## id >; \ > enable-method = "spin-table"; \ > cpu-release-addr = <0 0x8000fff8>; \ > }; > > > / { > model = "V2P-AARCH64"; > compatible = "arm,vexpress,v2p-aarch64", "arm,vexpress"; > > memory@80000000 { > device_type = "memory"; > reg = <0 0x80000000 0x4 0x00000000>; > }; > > > > cpus { > #address-cells = <1>; > #size-cells = <0>; > > #if CONF_CPUS == _2_2 > CPU(0,0x0) > CPU(1,0x1) > CPU(2,0x102) > CPU(3,0x103) > cpu-map { > cluster0 { > core0 { cpu = <&CPU0>; }; > core1 { cpu = <&CPU1>; }; > }; > cluster1 { > core0 { cpu = <&CPU2>; }; > core1 { cpu = <&CPU3>; }; > }; > }; > #elif CONF_CPUS == _2_4 > CPU(0,0x0) > CPU(1,0x1) > CPU(2,0x102) > CPU(3,0x103) > CPU(4,0x104) > CPU(5,0x105) > cpu-map { > cluster0 { > core0 { cpu = <&CPU0>; }; > core1 { cpu = <&CPU1>; }; > }; > cluster1 { > core0 { cpu = <&CPU2>; }; > core1 { cpu = <&CPU3>; }; > core2 { cpu = <&CPU4>; }; > core3 { cpu = <&CPU5>; }; > }; > }; > #else > #error Missing configuration section > #endif > }; > > virt-encoder { > compatible = "drm,virtual-encoder"; > port { > dp0_virt_input: endpoint@0 { > remote-endpoint = <&dp0_output>; > }; > }; > > display-timings { > native-mode = <&timing0>; > > timing0: timing_1080p60 { > /* 1920x1080-60 */ > clock-frequency = <148500000>; > hactive = <1920>; > vactive = <1080>; > hfront-porch = <148>; > hback-porch = <88>; > hsync-len = <44>; > vfront-porch = <36>; > vback-porch = <4>; > vsync-len = <5>; > }; > }; > }; > }; > > &dp0 { > status = "ok"; > > port { > dp0_output: endpoint@0 { > remote-endpoint = <&dp0_virt_input>; > }; > }; > }; > > **************************************************** > The problem is as follows: > **************************************************** > warn: Existing EnergyCtrl, but no enabled DVFSHandler found. > info: Entering event queue @ 0. Starting simulation. . . > warn: SCReg: Access to unknown device dcc0:site0 :pos0: fn7 :dev0 > warn :instruction' csdb unimplemented > warn: GIC APRn write ignored because not imp Lemented: 0xd0 > warn: GIC APRn write ignored because not implemented: 0xd4 > warn: GIC APRn write ignored because not imp Lemented: 0xd8 > warn: GIC APRn write ignored because not imp Lemented: 0xdc > warn: Address 0xfffff f8008091cc0 is outside of physical memory, stopping > fetch > warn: Address 0xffffff8008091cc0 is outside of phys ical memory, stopping > fetch > warn: Address 0xffffff8008091cc0 is outside of physical memory, stopping > fetch > warn: Address 0xffffff8008091cc0 is outside of physical memory, stopping > fetch > warn: Address oxfffff f8008091cc0 is outside of physical memory, stopping > fetch > warn: Tried to read RealView I/0 at offset 0x60 that doesn't exist > warn: Tried to read RealView I/0 at offset 0x48 that doesn't exist > warn: Tried to write RVIO at offset 0xa8 (data 0) that doesn't exist > warn: Tried to write RVIO at offset 0xa8 (data 0) that doesn't ex ist > warn: Tried to write RVIO at offset 0xa8 (data 0) that doesn't ex ist > warn: Tried to write RVIO at offset 0xa8 (data 0) that doesn't ex ist > warn: Tried to write RVIO at offset 0xa8 ( data 0) that doesn't exist > warn: Tried to write RVIO at offset 0xa8 (data 0) that doesn't exist > warn: Tried to write RVIO at offset 0xa8 (data 0) that doesn't ex ist > warn: Tried to write RVIO at offset 0xa8 (data 0) that doesn't ex ist > warn: Tried to write RVIO at offset 0xa8 (data 0) that doesn't ex ist > warn: Tried to write RVIO at offset 0xa8 (data 0) that doesn't exist > warn: Tried to read RealView I/0 at offset 0x8 that doesn't exist > warn: Tried to read RealView I/0 at offset 0x48 that doesn't exist > info: Dumping kernel dmesg buffer to sys tem. workload. dmesg. . . > warn: Kernel panic in s imulated kernel > > **************************************************** > I look forward to hearing your answers > **************************************************** > _______________________________________________ > gem5-dev mailing list -- [email protected] To unsubscribe send an email > to gem5-dev- > [email protected] %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s IMPORTANT NOTICE: The contents of this email and any attachments are confidential and may also be privileged. If you are not the intended recipient, please notify the sender immediately and do not disclose the contents to any other person, use it for any purpose, or store or copy the information in any medium. Thank you. _______________________________________________ gem5-dev mailing list -- [email protected] To unsubscribe send an email to [email protected] %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s
